Eaton EBMAFDD24 Bedienungsanleitung

EBMAFDD14-36 - ARC FAULT DETECTION DEVICE (AFDD) DISTRIBUTION BOARD

Instruction leaflet LT1230 (01/21)

IMPORTANT NOTES

1. This product should be installed, commissioned and maintained by or under the supervision of a competent electrician in

accordance withcurrent electricalengineeringCodesof Practice, Requirements forthe Electrical Installations(IET Wiring Regulations

BS7671), Construction (Design and Management)Regulations, HSG150- Health and Safety in Construction, Statutoryrequirements and

any specific instruction issued bythe Company.

2. After completingthe installationandtestingofthisproduct it is essentialthat thisleaflet is drawn tothe attentionof the person

responsibleforits future operationandmaintenance, andis at all timesavailable forreadyreference.

3. Thesenotesassume throughout that the product isdisconnected fromthe supply. It is essential that this isdone beforeanyworkis

carried out.

4. TheseDistribution Boardsa re designed for use with Eaton AFDDs only. Failure to comply willresult in i nvalid warranty and certification.

2.4Nm

300957 –EBMAFDD14 - 14 Way DB

300958 –EBMAFDD24 - 24 Way DB

300959 –EBMAFDD36 - 36 Way DB

Clip fit

This board is intended to be used

with Eaton AFDD devices

up to 40A

All unused ways must

Be covered with a

blanking module,

assembled and

fitted in gangs of 3.

EMPB

Important:

Orientate clip next

to busbar stack

Optional

SPD

position

Incoming

Switch position

Before fitting the AFDD to the busbar ensure the terminals are

fully open. Locate the AFDD square to the

busbar and tighten the terminals.

General note: Tightening torque for

M5 thread forming screws is 3.8Nm

Insert Lock into hole tighten back nut Remove plastic knob

Fitting Optional Door

Lock EMDL & EMPL

SP MCB / RCBO

Fit SP device on live stab,

ASLTT1001 direct

connection on neutral

stab and EMBP blank in

the spare module space.

ASLTT1001

SP Device

EMBP

Earth bolt

15Nm

2.5Nm

Fitting Incoming Switch

EMS1253 & EMS1253N

Before fitting the switch ensure the terminals arefully open. Locate

the switch onto the stabs ensuring the din rail clip is hooked over the

mounting bracket.

Mounting bracket

Din rail mounting clip

Fitting Neutral Link assy- 300960

Inner Cover Cutaway for 4P Incomer

When a 4 pole incomer is fitted the cutaway on

the inner cover needs to be removed .

Mounting

bracket hook

4.5Nm Single Phasing Kit - 300969

Position the two comb busbars back to back

and fit in the L1/L2/L3 fork terminals of the

switch on the incoming side.

2.4Nm

Connecting Boards Together

Connect downstream of the

Incoming switch so secondary

board switches with primary board.

Connect upstream of the incoming

switch so secondary board switches

independently of the primary board.

Neutrallink connection

Remove knock out

for N cable to exit

When the neutral link kit is fitted

then the cable is made up with a M6

lug and connected to the link

terminal as shown. The other end is

connected to the incoming neutral

terminal on the secondary board.

Make up 16mm² tri rated cable with Cembre ANE 3-U 5

fork connectors and connectto the incoming switch

fork terminals of the primary board. The other end of

the cables are connected to the main incoming

terminals on the Secondary board.

Secondary board 80A max.

Connecting boards with Neutrallink kit

Slide the neutral assembly into position with the mounting brackethook

engaged in the incomer mount. Bolt the neutral copper connection to the

busbar with the M5 x 12 bolt and spring washer provided to 4.5Nm.

6.8Nm

6Nm <=10mm²

9Nm >10mm²

2.4Nm

Surge SupressionDevice -300961 type 1 and 300962 type1&2

Before Installation: Verify that the system is wired in aThree Phase Star configuration and that the voltage rating of the system matches the

voltage rating ofthe SPD as shown on the label. If the Neutral to Earth voltage is greater than 5 VAC, then a problem may ex ist in the electrical

system. The SPD may be installed; however, a qualified person should be consulted to correctthe problem.

Installation Instructions:

• Disconnect the neutral cable from the SPD and remove the SPD and MCB from the

mount. Fit the mounting bracket assembly to the back plate in theposition shown.

• Fit 63A 4P MCB onto the stabs with the back end hooked on the din rail whilst

fitting the SPD device on the din rail next to it. Tighten the MCB terminals to 2.4Nm.

• Reconnect the Neutral cable to the SPD. Tighten to 2.4Nm.

• Connect the EARTH wire to the nearest common earth bolt. Tighten to 15Nm.

Energise the System. The Indicator should remain green.If the indicator turns RED,

de-energise and contactthe Technical Servicesdepartment.

2.4Nm

Separation Shield -300965

In some arrangements, when the distribution board is used in a cluster, a 20mm

spacer is required to allow thebottom and top of the boards to be flush

A separation shieldis required when boards aremounted on

top of each other and a barrieris required between them.

Position the separation shield

inside the board and fix with

M5 screws provided.

Alignment Spacer-300966

Fit the spacer to the top or bottom of the board and

fix with M5 screws. The removed Distribution board

gland plate can be refitted to the spacer if required.

20mm

spacer

SPD mounting

bracket assembly

Remove shield from stabs

before fitting the SPD

feeder MCB

H630 x W440

x D130 mm

H1260 x W440

x D130 mm

H900 x W440

x D130 mm

2.4Nm

Neutral

connection

2.4Nm

Warning -

Intellectual Property Rights

Eaton wishes to make it clear that it owns intellectual property rights in the

product which it manufactures (whether or not listed in this leaflet) and that it

will take legal action against any party found to be manufacturing, using, or

selling any article which infringes the company’s intellectual property. All

marks in this document identified with an R symbol or a TM symbol adjacent

to the mark are trademarks of Eaton.

The use to which this product is put and its place of installation is outside our

control. Particular care should therefore be taken to follow the instructions

given here and to ensure their continued availability in conjunction with the

use of the product.

No responsibility can be accepted by us if these instructions are disregarded.

Further copies of these instructions and information concerning the

installation and proper use of this product can be obtained by contacting the:

Technical Services Department

Eaton Electric Limited, Middleton,Manchester, M24 1GQ.

Tel: +44(0)8700 545 333,

email: techsupportemea@eaton.com

Maximum Thermal Ratings

Maximum Incomer

125ASwitch = 125 InA

FED FROM

______________________________________________________

CONTRACTOR

______________________________________________________

INSTALLATIONDATE

_______________________________

INCOMINGCABLESIZE

_______________________________

Maximum Outgoer InC RDF

AFDD 40A (6kA) = 40A 0.75

AFDD 25A (10kA) = 25A 0.75

MAIN BUSBARCIRCUITS

Dieses Handbuch passt für folgende Modelle

Andere Eaton Überspannungsschutz Handbücher

Eaton

Eaton DSFi Bedienungsanleitung

Eaton

Eaton Crouse-Hinds SD Series Benutzerhandbuch

Eaton

Eaton SPC Series Bedienungsanleitung

Eaton

Eaton BRSURGECSA Series Installationsanleitung

Eaton

Eaton SPD3200-TN-E Bedienungsanleitung

Eaton

Eaton Protection Box 5 Bedienungsanleitung

Eaton

Eaton Innovative Technology XT50 Bedienungsanleitung

Eaton

Eaton SPD Series Bedienungsanleitung

Eaton

Eaton SPI-35/440 Handbuch

Eaton

Eaton **CF***10 series Bedienungsanleitung

Eaton

Eaton PVD40 Series Bedienungsanleitung

Eaton

Eaton TRIPP LITE Series Bedienungsanleitung

Eaton

Eaton Powerware SPDT60-255 Bedienungsanleitung

Eaton

Eaton MEMSHIELD 3 EPBN1SPD123 Service-Handbuch

Eaton

Eaton IM01005012E Bedienungsanleitung

Eaton

Eaton PH Series Bedienungsanleitung

Eaton

Eaton EM3SSK3T2 Bedienungsanleitung

Eaton

Eaton RSPF Series Bedienungsanleitung

Eaton

Eaton SPC Series Bedienungsanleitung

Eaton

Eaton SP2 Leitfaden

Eaton

Eaton SPD Series Bedienungsanleitung

Eaton

Eaton SPD Series Bedienungsanleitung

Eaton

Eaton AFDD+ Handbuch

Eaton

Eaton Crouse-hinds series Bedienungsanleitung

Beliebte Überspannungsschutz Handbücher anderer Marken

ELAC

ELAC ProteK PR91-W Bedienungsanleitung

Tsubaki

Tsubaki TSM4000M1 Bedienungsanleitung

QVS

QVS PP134C Bedienungsanleitung

CyberPower

CyberPower CSP604T Bedienungsanleitung

Davis Instruments

Davis Instruments Radio Surge Protector Bedienungsanleitung

M-system

M-system MGA-100 Bedienungsanleitung

CyberPower

CyberPower CSP706T Bedienungsanleitung

CyberPower

CyberPower B300WRC1 Bedienungsanleitung

M-system

M-system MGD-24 Bedienungsanleitung

Leviton

Leviton 51120-3R Bedienungsanleitung

Panamax

Panamax MAX 5400-EX Bedienungsanleitung

CyberPower

CyberPower B1006T Bedienungsanleitung

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 Bedienungsanleitung

Minuteman

Minuteman MMS7120RCT Bedienungsanleitung

Leviton

Leviton 52412-DS3 Bedienungsanleitung

Savio

Savio LZ-07 Bedienungsanleitung

Siemens

Siemens HNM3M120 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF Bedienungsanleitung