Eazy RC ERC-1 Bedienungsanleitung

ERC-1 Remote Control

EAZYRC

1.Unplug the battery from your plane.

2.Carefully plug the charger into the USB

port on your computer or USB adapter.

3.Connect battery into the charger.

4.The charging process takes about 3.5

hours.For safety reasons, never charge

the battery for longer than 4 hours.

5. While charging, the red LED indicator will

be constant on.When the charging is

finished, the red LED will be off.

1.Install 4AA batteries(not included) in the transmitter.

Transmitter assembly

Charging Instruction

Setup Instruction

Binding Instruction

Binding is the process of programming the receiver to recognize the GUID(Globally Unique

Identiﬁer) code of a single speciﬁc transmitter. When a receiver is bound to a transmitter, the

receiver will only respond to that speciﬁc transmitter.

Binding steps：1.Keep the transmitter switched OFF, throttle joystick at buttom position.

2.Connect the battery to the plane, then turn on the transmitter within 5 seconds.

3.The receiver LED will ﬂash for 3-8 seconds to bind automatically.

4.After the receiver LED stop ﬂashing, it means the binding process is done.

NOTICE：Keep Gyro switch at Middle or Beginner position.

NOTICE：Keep the planes til in a calm environment for calculating the Gyro.

Throttle Unlock(Arming)

To prevent from damages, the throttle channel is locked each time when powering on your

transmitter. Follow below instruction to unlock the throttle.

Turn the throttle stick up to max position until you hear a"beep"sound.

Then turn the throttle stick down to min position until you hear a"beep"sound.

Now the throttle is unlocked.

CAUTION ：Keep the propeller in distance for your safety.

Gyro Switch

Three modes available:

Manual/Gyro OFF (EXPERT)

Soft Gyro Assit(MIDD)

Strong Gyro Assit (BEGINNER)

Soft Gyro Assit(MIDD)Soft Gyro Assit(MIDD)

Strong Gyro Assit

(BEGINNER)

Strong Gyro Assit

(BEGINNER)

Manual/Gyro OFF

(EXPERT)

Transmitter Instruction

Power status LED

One-key Aerobatics

Button

One-key U-turn

Activation

Throttle

Rudder

Rudder trim

One-key U-turn Switch

Gyro Switch

Elevator trim

Elevator

Aileron

Aileron trim

Power switch

One-key Return to Home Instruction

NOTE：1. Every time when you power on the plane, it requires to activate the one-key U-turn function.

2. To use this function during ﬂight, press the one-key return to home switch button，the plane

will turnaround automatically, back to the opposite direction where it takes o฀. No matter you

ﬂies the plane under manual control or gyro assist mode, when you turn on the one-key return to

home function, the plane will enter gyro assist mode automatically to help stable ﬂying back.

3. To quit this function, just press again the switch button, or control any servo stick(rudder/ele -

vator), the plane will back to your control immediately. When you quit this function, the plane will

back to the what the control mode it was.

The one-key return to home function allows the plane to U-turn by the opposite direction that the

plane takes off.

Follow below steps to activate the function.

1.Place your plane heading to the take-off direction.

2.Do NOT unlock the throttle，press the activation button and hold for several seconds until you

hear a"beep"sound, the rudder surface will respond, meaning the one-key return to home

function is now activated.

The one-key Rollover feature allows beginner

pilot to perform aerobatic actions by simply

pressing the button on transmitter.

During ﬂight, under gyro control mode, press

the one- key Rollover button, the transmitter

will beep several times. During the beeping,

simply move the aileron stick to either

direction for auto-roll, or move the elevator

stick to either direction for auto-ﬂip.

One-key Rollover

One-key Rollover Instruction

CAUTION：This function is bound to the

receiver, instead of to the transmitter，which

means the plane will return ONLY to the

opposite direction that the plane takes off. In

other words, this function can only make the

aircraft ﬂy in the opposite direction of the

setting, and cannot be used as a ﬁxed-point

return. It is not based on the position at the

time of setting.

One-key U-turn

Activation

One-key U-turn

Switch

warning

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliancecould void the user's authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected.-- Consult the dealer or an experienced radio/TV technician for help.The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.FCC ID: 2AUBX-ERC-1

Inhaltsverzeichnis

Andere Eazy RC Fernbedienung Handbücher