Eclipse RCS-BELTROL ESC Bedienungsanleitung

- 2 -

INSTALLING RCS-BELTROL ESC’s.

SPEKTRUM IS A GROUP “A” R/C & THIS ESC MUST USE THE BTLvA1 OPERATING PROGRAM.

RCS-BELTROL ESC’s can use a DX5e 5 channel 2.4 GHz digital proportional R/C AR500 RX with servo outputs.

Other Spektrum RX’s can be used but we have not tested all of them.

We have conducted development & testing with both Mode # 1 & Mode # 2 systems. See page # 4.

These have sprung Elevator & non sprung Throttle controls which are used to control the locomotive.

The RCS-BELTROL program uses the L to R Aileron & Rudder sticks to trigger 4 x sound effects or control accessories.

Channel # 5 (the Landing Gear control switch) is used for initial speed calibration, making system program changes such

as Start/Max voltage, default direction start, system reset & sound trigger outputs from momentary to latch ON - OFF

See page # 7 for information as to how the TX sticks are used.

LOCOMOTIVE SEPARATION.

It is not necessary to separate 2.4 GHz R/C R/C systems with crystals. They are all legal for air & ground use. Every TX

has a unique identifier code and any AR500 receiver (RX) can be “BOUND” to any DX5e TX.

“BINDING” must be done before the system can be used. Ideally it should be done before the RX is plugged into the #

DEC-U pcb. However, if this is not possible, we have supplied a 3 way cable to temporarily join the RX to the # DEC-U

before final installation. This will allow access to the “BINDING” socket on the RX for the “BINDING” plug supplied with

the DX5e AR-500 RX. See page # 4 for the “BINDING” procedure.

Insert “BINDING” plug. Then place # EX-LD into any RX &

# DEC-U sockets. Orange to centre of pcb. Follow page # 5. Remove the # EX-LD & binding plug before installing the RX

into the # DEC-U. # DEC-U & AR-500 RX shown.

The BATTERY – BIND terminals must NOT be connected.

You can mount the # DEC-U PCB with double stick tape or non conductive silicone. Do not allow metal objects to touch

the rear of the PCB. Damage to the PCB may result.

INSERTING THE DX5e RX.

The DX5e 2.4 GHz AR-500 RX simply plugs into the # DEC-U upside down & eliminates all servo leads. Be careful

locating the pins into the pcb sockets. You must accurately align the RX pins to the numbers shown. 1 – 6.

It will be a stiff push fit, but do not force the RX home.

The # DEC-U provides a 5 volt BEC supply for the 5 channel DX5e 2.4 GHz RX. You do not need batteries for the RX.

Hold one part in each hand.

Carefully line up pins # 1 – 6.

Then gently press onto socket.

The fit will be tight. Do not force.

We understand other Spektrum RX’s may have different servo lead spacings and will not plug into the # DEC-U pcb. In

this case it will be necessary to separately purchase the # DEC-ADPT kit with individual servo leads.

- 3 -

Alternately, the separately sold # DEC-ADAPT” kit permits the RX to be mounted anywhere you wish.

With the addition of the # BINDER, this kit will also enable you to have an “at will” BINDING capability to hand over locos

to a different TX. EG. Adding & removing speed matched locos to a train. See page # 6 3.1 & 3.2. Speed matching.

The # DEC-ADPT kit.

(Prototype kit shown). Insert the 1 x 3 way servo cable & four

single wire cables into the DX5e RX. The

3 x wire cable goes to # 1 servo output.

Carefully line up the # DEC-ADAPT”

pcb with pin #’s 1 - 6 on the # DEC-

Adapt & gently press it onto the pins.

PLACING RX ANTENNA.

Other than with brass locos, it does not matter where you place the antenna(s).

We have 200’ + range with the system in plastic locos. There is NO “glitching” or “Rusty Bolt Effect”.

N.B. With metal locos the antenna may need to be vented externally to maximise range. Although there is evidence that

2.4 GHz RX’s have been successfully used with the RX & antenna inside a dummy water tank of a live steam loco,.

Turn the DX5e 2.4 GHz TX OFF to save the batteries & the loco will “Cruise” along until the TX is turned ON again &

manual control resumed. The RCS-BELTROL program ignores the SPEKTRUM DX5e Fail safe.

INSTALLING THE RCS-BELTROL ESC.

Wiring diagrams for your specific ESC must be downloaded in pdf format from the BELTROL website.

http://www.beltrol-rc.com/p1332-Instructions.html

POWER SOURCES.

You can use battery power. OR: Constant track voltage. See below.

Maximum voltages for a particular ESC are shown on page # 1.

BATTERY POWER.

Connect the traction battery, which MUST BE FUSED, as per the wiring diagram.

RCS-BELTROL R/C offers a variety of installation kits for on board use such as the # BIK-U3/6 which has screw

terminals to simplify installations. For trail car installations we also have the # BIK-TC5.

When used with the Bachmann®K-27, we have a special kit, # BIK-K27 to simplify installation.

PnP TRACK POWER.

The # PnP-ADAPT is a Plug’n’Play pcb designed to be used with AristoCraft®and Bachmann®locos equipped with the

standard PnP socket. It will collect constant track voltage which is then polarised, filtered, fused & connects to any

ECLIPSE ESC w/screw terminals. Filtered DC is recommended. You may be able to use a non DC supply such as DCC.

Battery back up of the track power is available via screw terminals on the # PnP-ADAPT.

Make sure the battery pack is fully charged before using the system.

NON PnP TRACK POWER.

Contact RCS-BELTROL for advice on how to set up a bridge rectifier and filtering capacitors circuit.

MOTOR CONNECTION.

Connect the motor(s) as per the wiring diagrams. The M + motor output is positive (+) in a forward direction.

In most installations the system will function perfectly well without any extra motor “Noise” suppression.

The # ECL-PnP is a simple plug in installation. No wiring to the motors or lights.

AristoCraft®locos. We supply the # ECL-PnP programmed with the default pre-set to suit AristoCraft®locos.

Bachmann®Spectrum®Fn3 locos. You can easily reset the # ECL-PnP default direction to suit the Bachmann®

Spectrum®Fn3 locos that have a PnP socket. See page # 6, 3.4 Default Direction.

SHORT CIRCUIT & OVERLOAD PROTECTION.

All RCS-BELTROL ESC’s are self protecting.

Although there is output overload and short circuit protection built into them, it is essential the track power and battery

supply be fused for overall system protection. See the wiring diagram pages.

RCS-BELTROL ESC’s have transistor controlled directional lighting. Maximum current is 100 ma per terminal.

IT IS MOST IMPORTANT THAT THE LIGHT BULBS BE COMPLETELY ISOLATED FROM ANY OTHER WIRING.

Instead of rewiring some locos, sometimes it is much simpler to control the regular loco wiring by simply reversing the

traction battery voltage. You can use the # RELAY-1a to do this as it can save a lot of wiring in many locos. It is

especially useful in USA Trains®locos to control incandescent bulbs or LED’s up to 1 amp & smoke features.

Please note: If the # RELAY-1a has been used, the lights will flash alternately, not together as with transistor outputs.

When the system is in neutral only one set of lights will be lit.

The instructions assume the operator has used the available front & rear transistor lighting outputs or # RELAY-v5.

If you do not have any lighting outputs connected you MUST be able to observe the LED on the ESC.

- 4 -

SETTING UP THE RCS-BELTROL ESC’s.

THESE INSTRUCTIONS REFER TO THE SPEKTRUM DX5e 2.4 GHz 5 CHANNEL R/C.

LAYOUT OF THE DX5e TRANSMITTER.

Shown above is a Mode # 1 TX.

The Elevator & Rudder stick is on the left.

The Throttle & Aileron stick is on the right

Shown above is a Mode # 2 TX.

The Elevator & Rudder stick is on the right.

The Throttle & Aileron stick is on the left

Prior to using this system there are two procedures that must be carried out by the operator.

1. “BINDING”.

The 1st procedure is to “BIND” the DX5e receiver (RX) to the Transmitter (TX).

“BINDING” is accomplished by following a few simple steps that are outlined in the R/C system instructions.

Although the RCS-BELTROL program ignores the RX Fail Safe commands, before “BINDING” the operator should

nevertheless set up the failsafe as SPEKTRUM intended. Set the servo reversing switches to normal.

The operator must have the spring loaded TX stick positions in neutral & the throttle stick to zero. Stick down.

Firstly set up the TX trim tabs on all four control sticks. These MUST be in the middle.

The SPEKTRUM DX5e has spring loaded digital trim switches. These have 40 positions from one extreme to the other &

beep every time they are moved. To accurately determine the neutral position of the trim switches, hold each switch in

one direction until it stops beeping. Then press and hold it again to make sure it has reached the extreme. To get back

to the middle of the range (neutral) press & hold the switch the opposite way until the fast but quiet beeps stop & the

beeps once again are loud. Let the switch go. This is neutral.

Once the digital trim switches are in neutral you can proceed with the “BINDING” process.

There is no trim switch on Ch # 5 which must be set to the “0” position. Set the Rate switch to HI.

The TRIM switches are easy to accidentally move. Re-center them occasionally. No need to rebind.

HOW TO “BIND”.

1.1 Firstly insert the “BINDING” plug supplied with the R/C system into the “BINDING” socket on the DX5e AR-500 RX.

See pages # 2 & # 3 for information about gaining access to the “BINDING” socket.

1.2 Turn the loco power ON. The RX LED will start blinking very rapidly to indicate it is ready to be bound.

Please note the green LED on the ESC pcb & the front and rear lights (if fitted) will stay OFF.

The loco will always give a very slight jerk at switch ON. See Page # 9.

1.3 Pull the long spring loaded TRAINER switch towards you and hold it in position.

1.4 Turn the TX power switch to ON. Almost immediately the four LED’s on the TX will start blinking.

1.5 Release TRAINER stick. The RX LED will blink more slowly indicating the binding process has started.

When “BINDING” is complete the RX LED will change to solid ON & the ESC LED & both loco lights will immediately blink

three times & then go to solid ON.

N.B. The “BINDING” plug MUST be removed (or pushbutton released) BEFORE the RX is turned OFF.

1.6 The “BINDING” plug is removed & stored safely. Then remove the 3 x wire extension lead. Then replace the DX5e

AR-500 RX in the sockets provided on the # DEC-U. Only Pin #’s 1 – 6 are used & must be lined up accurately. There is

no connection to the Battery/Bind terminals.

The R/C system is now ready for speed calibration.

- 5 -

2. CALIBRATION.

The 2nd step in system preparation is to calibrate the direction & throttle sticks. Even though this step is only needed

once when first setting up a new ESC, from time to time it is advisable to run through the procedure.

2.1 Turn ON the loco power. The RX LED, ESC LED & the loco lights stay OFF.

2.2 Set the DX5e Mode # 2 channel # 5 switch

on the TX to # 1 ON, i.e. pull switch towards you.

2.3 Turn the TX ON. RH LED will illuminate.

Make sure Throttle stick is down. Zero output.

After a few seconds (between 2 - 8 seconds) RX & TX will recognise each other & the RX LED will come ON. The ESC

LED & both front & rear lights will flash rapidly.

2.4 From zero (down position), gently stroke the Throttle stick backwards & forwards full travel a couple of times.

Pause briefly at end of each stroke. Then return stick to zero (down position).

2.5 Gently stroke the Elevator stick backwards & forwards

full travel a couple of times & let stick go.

2.6 Turn the Channel # 5 switch to “0” OFF.

i.e. push switch away from you.

The ESC LED & loco lights will blink three times at a slower rate & both lights will go to solid ON.

The system is in neutral and ready to operate.

2.7 Either turn the loco and TX OFF for later use, or proceed to page # 6.

- 6 -

3. PROGRAMMING.

Operating features of the RCS-BELTROL system can be programmed from the TX by turning on CH # 5.

Programming can only take place when the system is in neutral.

3.1 START VOLTAGE. This feature is designed to equalise the starting voltage of dissimilar locos.

3.2 TOP SPEED VOLTAGE. This can limit the top speed available. Either for speed matching locos or, for limiting the

top speed of one loco, say for when the system is being operated by children.

3.3 MOMENTUM. Toggle momentum control ON or OFF.

3.4 DEFAULT DIRECTION. Re-set the direction of a loco when it is to run back to back with another loco.

3.5 SYSTEM RESET. This takes # 1 & # 2 back to the factory default if incorrectly set.

3.6/7/8/9 SET SOUND TRIGGERS 1, 2, 3 & 4 from MOM (Default) to Latch ON - OFF.

HOW TO USE THE PROGRAMMING FEATURE.

Turn ON the loco power. The loco will give a slight jerk & the RX and loco lights will stay OFF.

After switch ON, the system will be, & must stay, in neutral. If running, return to neutral before programming.

Only turn the Ch # 5 switch ON AFTER the TX has been turned on. Do not turn the Ch # 5 switch on first.

SPEED MATCHING.

If you have two or more locos that have dissimilar starting and top speeds, you can adjust those voltages so the locos will

be fairly accurately speed matched across the speed range. It has been our experience that absolutely accurate

matching is not really needed for smooth performance. The trade off is the top speed of a consist of locos controlled by

one TX will be limited to the top speed of the slowest loco.

3.1 START VOLTAGE. We suggest you test the locos you wish to match one at a time to find out the stick setting at

which the slowest starting locos begin to move. Count the number of clicks on the throttle stick from OFF (down).

Then, with the slowest loco stopped and the direction set to neutral:

Move the throttle stick to the loco start speed desired. i.e. to the stick position where the loco started moving.

Then push the direction (elevator) stick forwards once only. The lights will blink ONCE with the push.

Wait a couple of seconds for the lights to blink ONCE again indicating the new start voltage setting has been stored in the

system memory. Then move the throttle stick back to zero (OFF) position. i.e. stick down.

Then turn channel # 5 OFF. The lights will blink three times and then go to all solid ON. i.e. Neutral.

Repeat the procedure if the setting is incorrect.

3.2 TOP SPEED VOLTAGE. If speed matching, we suggest you test the locos you wish to match one at a time to find

out the stick setting at which the fastest loco matches the top speed of the slowest loco.

Then, with the fastest loco stopped and the direction set to neutral:

Move the throttle stick to the lower top speed desired for the loco. i.e. to the stick position where the fastest loco matched

the top speed of the slowest loco.

Then push the direction (elevator) stick forwards TWICE only. The lights will blink once with each push.

Wait a couple of seconds for the lights to blink TWICE again indicating the new top speed voltage setting has been stored

in the system memory. Then move the throttle stick back to zero (OFF) position. i.e. stick down.

Then turn channel # 5 OFF. The lights will blink three times and then go to all solid ON. i.e. Neutral.

Repeat the procedure if the setting is incorrect.

OR: When children are using the loco, you can follow the same steps to limit the top speed of any loco.

3.3 MOMENTUM. Toggle momentum control ON or OFF.

Press the elevator stick forwards THREE times only. The lights will blink once with each push.

Wait a couple of seconds for the lights to blink THREE times again indicating the default momentum ON – OFF setting

has been stored in the system memory.

Then turn channel # 5 OFF. The lights will blink three times and then go to all solid ON. i.e. Neutral.

3.4 DEFAULT DIRECTION. To re-set the default direction of a loco to run back to back with another loco:

Push the direction (elevator) stick forwards FOUR times only. The lights will blink once with each push.

Wait a couple of seconds for the lights to blink FOUR times again indicating the default direction setting has been stored

in the system memory.

Then turn channel # 5 OFF. The lights will blink three times and then go to all solid ON. i.e. Neutral.

3.5 SYSTEM RESET. To take # 3.1 & # 3.2 back to the factory default if incorrectly set:

Push the direction (elevator) stick forwards FIVE times only. The lights will blink once with each push.

Wait a couple of seconds for the lights to blink FIVE times again indicating the start & top speed voltage settings have

been returned to default in the system memory.

Then turn channel # 5 OFF. The lights will blink three times and then go to all solid ON. i.e. Neutral.

3.6/7/8/9 SET SOUND TRIGGERS 1, 2, 3 & 4 from MOM (Default) to Latch ON - OFF.

For trigger # 1 Push the direction (elevator) stick forwards SIX times only. The lights will blink once with each push.

Wait a couple of seconds for the lights to blink SIX times again, indicating the trigger has toggled to latch ON-OFF.

Then turn channel # 5 OFF. The lights will blink three times and then go to all solid ON. i.e. Neutral.

Repeat procedure for trigger #2(SEVEN pushes) trigger # 3 (EIGHT pushes) & trigger # 4 (NINE pushes).

Repeat procedure to change any of the 4 x triggers back to MOMENTARY from Latch ON – OFF.

- 7 -

OPERATING THE RCS-BELTROL ESC’s.

4. HOW TO OPERATE.

N.B. The TX Ch # 5 switch must be OFF and the TX RATE switch must be set HI.

THE THROTTLE STICK MUST BE ALL THE WAY DOWN BEFORE TURNING SYSTEM ON.

Always turn ON the loco first. The loco will give a slight jerk (See page # 9) & the ESC & loco the lights will stay OFF.

Then turn the TX ON. After between 2 - 8 seconds the TX & RX will recognise each other. The RX LED will come ON &

not blink. The ESC LED & both front & rear loco lights (if fitted) will blink three times & then all lights will go to solid ON.

N.B. In order to select a direction the throttle stick must be OFF and the system must be in neutral.

4.1 FORWARDS. To select forwards direction push the Elevator stick fully forwards once & then release it.

The rear light will go out. The green LED on the ESC pcb & the front light will stay ON.

If the # ECL ESC default motor & lights direction is incorrect please see TROUBLESHOOTING on page # 9.

4.2 SPEEDING UP. Gently push the Throttle stick forwards. The loco will accelerate away after 3 - 4 clicks.

The speed is proportional to the stick position with a small amount of momentum built in to prevent sudden jerky

movements. Let the stick go once the desired speed has been reached. The speed will stay the same until the Throttle

stick is moved either up or down. Zero - Max speed takes 2 x seconds.

Turn the DX5e 2.4 GHz TX OFF to save the batteries & the loco will “Cruise” along until the TX is turned ON again &

manual control resumed. The RCS-BELTROL program ignores the SPEKTRUM DX5e Fail safe.

4.3 SLOWING DOWN. Pull the Throttle stick back to the desired speed. Max - Zero speed takes 2 x seconds.

4.4 STOPPING. Pull the Throttle stick back all the way back to stop. The ESC LED & front light will be ON.

4.5 REVERSE.You must completely stop the loco first. The Throttle stick must be all the way down.

Then pull the Elevator stick fully back once & release it to return the system to neutral from forwards.

The ESC LED plus both front and rear lights will be ON.

Then pull the stick back again & release it. The ESC LED & front light will go out. The rear light will stay ON.

To speed up, slow down & stop in reverse see SPEEDING UP, SLOWING DOWN & STOPPING above.

CONTROLLING MOMENTUM & SOUND TRIGGERS.

The RCS-BELTROL ESC’s feature controllable momentum. An operator can control precisely how much or how little

momentum effect is applied whilst accelerating and braking. The default is Momentum enabled.

Momentum can either be ignored or switched off. See page # 6 - # 3.3 for how to switch momentum OFF.

BRAKE RELEASE.

Once direction has been set (see 4.1 above) pull the direction stick back (down) fully & HOLD stick in place.

Then use the Throttle stick to set the speed you wish to attain.

If you hold the direction stick down the loco will start to accelerate up to the set speed at the slowest rate of acceleration

(30 seconds from zero to top speed).

The acceleration rate is proportional to the stick position. Fully down = 30 seconds, half down = 15 seconds.

Let the direction stick go & the loco will accelerate at the fastest rate (2 secs from zero to full speed) up to the set speed.

BRAKE APPLY.

Whilst the loco is running pull the direction stick all the way back (down) fully and HOLD stick in place.

Then use the Throttle stick to set the speed to zero.

If you hold the direction stick down the loco will start to decelerate to the set speed at the slowest rate of braking (30

seconds from top speed to zero).

The braking rate is proportional to the stick position. Fully down = 30 seconds, half down = 15 seconds.

If you let the stick go the loco will decelerate at the fastest rate (2 x seconds from full speed to zero).

SOUND SYSTEM TRIGGERS.

RCS-BELTROL ESC’s have 4 x four manual sound triggers controlled by the sprung left to right Aileron & Rudder stick

controls. Outlets are marked 1 – 4 on the row of 8 x screw terminals on the # DEC-U pcb. Max current is 100 ma.

You can activate any sound with any trigger depending on which TX stick you want to operate the sound with.

Mode # 1 & Mode # 2 sound triggers are both the same.

RH stick to the left is F 1. RH stick to the right is F 2. LH stick to the left is F 3. LH stick to the right is F 4.

The default for each is Momentary. All are programmable for latch ON – OFF instead. See page # 6. 3.6/7/8/9.

If you prefer the trigger outputs the other way around, it is OK to reverse the Aileron & Rudder reversing switches.

Do not reverse the THROTTLE & ELEVATOR switches.

When using with Momentary function, press the stick until the sound is activated. Release stick to turn sound OFF.

When using with a Latch ON – OFF function, press and hold the stick for one second until the sound is activated. Then

release the stick and the sound will stay ON. Press the same stick for one second & release to turn the sound OFF.

They can be used as is with most sound systems such as Sierra®, Phoenix®, Dallee®& MyLocosound®.

Sierra will require the additional purchase of one # SSI-12v5 so that Sierra can function correctly.

- 8 -

RCS-BELTROL ESC MU’ing LOCO CONSISTS.

MULTIPLE LOCOS IN A CONSIST.

The RCS-BELTROL ESC’s are capable of MU’ing multiple locos in one consist of locos.

You can add as many speed matched locos to the loco consist, as you like. Each loco must be bound to the controlling

TX. Follow the “BINDING” procedure described above on page # 4.

If the loco to be added has already been speed calibrated, there is no need to repeat the calibration step.

The RCS-BELTROL program permits reversing default direction & speed matching of locos. Settings for these features

are stored in the ESC so that any loco can be acquired by any TX. See page # 6.

HOW TO ADD LOCOS TO A CONSIST.

Turn the first loco OFF. Turn the second loco ON and drive it into position. Turn the first loco back ON.

The lock in feature of the system ensures the direction is set positively. Just make sure both locos are at zero output

before changing direction. To make sure the direction is set correctly for all locos in a consist, press the direction stick

twice from neutral. Once the direction is set it cannot accidentally change back to neutral.

DELETING LOCOS FROM A CONSIST.

Turn OFF the “to be retained” loco. Leave the “to be deleted” loco ON & drive it away, or, rebind it to a different TX

for use by another operator. See page # 4.

RCS-BELTROL ESC used with the current model QSI®sound.

DO NOT use the PWM ESC’s. Only the ECL-6rF RCS-BELTROL ESC can be used with a QSI®sound system fitted to

a PnP socket inside an AristoCraft®loco. The ECL-6rF controls QSI®sound correctly with outstandingly smooth slow

speed acceleration & braking. The only practical way to use it is in a trail car with the batteries etc. We recommend a

minimum of 18 volts nominal. You can safely use up to 24 volts nominal.

Simply connect the output of the RCS-BELTROL ESC to the pigtails on the back of the AristoCraft®loco.

For other brands of locos refer to the QSI®instructions. The track pick ups MUST be disabled.

You can use the QSI®as delivered with default “REGULATED THROTTLE CONTROL”. We recommend resetting to

“STANDARD THROTTLE CONTROL” with level 2 load BEFORE setting an idle voltage.

The QSI®sound system needs to have an idle voltage applied so that when the loco has stopped the sound system is

kept alive. The RCS-BELTROL system can be programmed to do this. Here is how to do it.

Once the TX & RX have been bound together you need to calibrate the loco speed as described on page # 4.

Once calibrated you now need to set the idle voltage which in effect is the same as setting the start speed.

With the loco switched on gradually apply throttle until the sound system comes ON. Note TX stick position

Continue to carefully apply throttle until the loco just begins to move. Once again note the stick position.

You need to decide at which point it is that best suits your application. We suggest the idle (i.e. start) voltage should be

set midway between the two stick positions you have just determined. Once you have determined what the start voltage

is to be, take the throttle stick back down to zero and set the direction to neutral.

Now go into RCS-BELTROL programming mode (see page # 6 section 3.1.).

After entering programming mode, set the throttle stick position as recommended above.

Then push the direction (elevator) stick forwards once only. The lights will blink ONCE with the push.

Wait a couple of seconds for the lights to blink ONCE again indicating the new start voltage setting has been stored in the

system memory. Then move the throttle stick back to zero (OFF) position. i.e. Stick down.

Then turn channel # 5 OFF. The lights will blink three times and then go to all solid ON. i.e. Neutral.

The QSI®sound system will come on and you are now ready to operate.

CONTROLLING THE SPEED OF A QSI®EQUIPPED LOCO.

To control the loco see page # 7 section 4.1. etc. The loco will NOT jerk when power is switched ON.

If the direction is wrong, simply swap over the two wires coming from MM on the RCS-BELTROL ESC.

When stopped the sound will remain in idle.

CAUTION. DO NOT CONNECT THE OUTPUT OF THE ESC TO ANY NON QSI®EQUIPPED LOCOS.

TRIGGERING THE QSI® SOUND SYSTEM WHISTLE/HORN & BELL.

You will need to fit the RCS-BELTROL # FLIPPER in series in the MM leads and connect the trigger to the appropriate

terminal on the RCS-BELTROL ESC. See the special # FLIPPER wiring diagram.

One or the other of the sideways sticks will trigger the output functions. Only one half of the stick is used.

The stick should be moved one way very briefly to turn the Bell ON & very briefly again to turn the Bell OFF.

Move the same stick the same way & hold it to play the Whistle/Horn. Let the stick go & the play will cease.

- 9 -

RCS-BELTROL ESC TROUBLESHOOTING.

No matter how carefully we think we have explained how to do things we do acknowledge we might have made mistakes

or omissions. Here are some possible problem situations to look out for.

IF NOTHING WORKS AT ALL:

SPEKTRUM IS A GROUP “A” R/C & THIS ESC MUST USE THE BTLvA1 OPERATING PROGRAM.

WHEN THE LOCO IS SWITCHED ON THERE IS A SLIGHT JERK.

This is normal. The slight jerk indicates power is connected to the system and the IC has powered up.

WHEN THE LOCO IS SWITCHED ON ACCESSORY OUTPUT # 1 MAY TRIGGER BRIEFLY.

This is also normal. A sound system function connected to output # 1 may trigger. Our testing shows no sign of this

actually happening with Phoenix and Sierra. But, it is possible.

WHEN THE LOCO IS SWITCHED ON, ALL LIGHTS COME ON WITHOUT BLINKING & NOTHING WORKS.

This can occur when the TX is switched ON after the loco, with the throttle stick not fully OFF (down).

SOLUTION. Ensure the throttle stick is completely OFF. The lights will then blink to indicate linking.

THE LOCO DIRECTION SET STICK & OR SPEED CONTROL IS BACKWARDS.

It is most important to ensure that the servo reversing switches are ALL set to normal.

When the direction is set to forwards the front light must come ON. If it doesn’t, reverse the elevator switch.

If the speed is backwards to the lighting direction you must reverse the wiring to the motor(s).

WEIRD ESC BEHAVIOUR FOR NO APPARENT REASON.

The most likely problems an operator will encounter when operating is when the Ch # 5 switch has been left ON or

accidentally turned ON.

SITUATION # 1. If, when the TX is first turned on & the lights blink rapidly, it is because the Ch # 5 switch is ON & the

system has entered calibration mode. This may happen with the DX6i. The Ch # 5 is backwards.

SOLUTION. Turn the TX OFF. Select the OFF position for the Ch # 5 switch & then turn TX back ON again.

SITUATION # 2. You have been running & for no apparent reason the lights all went out when you selected neutral &

you have no control. This means the Ch # 5 switch was turned ON during running & the system has entered

programming mode. CAUTION do not move any control sticks as you may make a program change.

SOLUTION. Before you do anything else, simply turn Ch # 5 OFF & the system will revert to normal operation.

SITUATION # 3. The system was working and for some reason you had a panic situation. You stopped the loco and

switched TX off. When you switched back on the loco lights were flashing and you moved the sticks to try and move the

loco and now nothing works. You have accidentally turned the Ch # 5 switch ON at some stage and altered the original

speed and direction calibration.

SOLUTION. Recalibrate the system. See page # 4.

Or; when the Rate switch is set to 70% and not the 100% it should be.

SITUATION # 4. The system was working and now you have trouble selecting a direction and cannot get any speed from

the loco. Or; it seems to lose programming when you try and accelerate.

This could be because you have the Rate switch accidentally set to 70% and not 100% as it should be. When set to 70%

the useable stick travel is reduced and can create quite odd effects.

SOLUTION. Set the rate switch to 100%. You may need to re-calibrate the speed & direction as well.

DEFAULT START UP DIRECTION.

When using the # PnP-ADAPT, the # ECL-3r & # ECL-6r ESC’s are programmed to be the same as the AristoCraft®on

board TE. As such, the motor direction & lights for Bachmann®PnP socket equipped locos will need to be reset. See

page # 6 section 3.4.

The PnP socket and lights are also wired backwards on some AristoCraft®locos. In this case the default direction will

also need to be reset. See page # 6 section 3.4. OR:

You can simply swap over the wires at the # PnP-ADAPT screw terminals.

PLEASE ADVISE US OF ANY OTHER PROBLEMS ENCOUNTERED & WE WILL INCLUDE THEM HERE.

SPECIAL NOTE REGARDING THE SPEKTRUM DX6i & DX7 TX.

The SPEKTRUM DX6i & DX7 transmitters are essentially the same as the DX5e. Set up of the system is also the same.

However, the DX6i TX has the channel # 5 switch configured back to front compared to the DX5e TX.

With the DX6i # 0 is ON & # 1 is OFF. It is most important that this switch is set to OFF unless you are programming.

DX6i has a nifty instant Throttle OFF button for emergency stops. Press that button & the loco will stop in 2 – 3 seconds.

CARE & FEEDING OF THE DX5e TX.

The SPEKTRUM DX5e transmitter uses 4 x AA size batteries. Either Alkaline dry cells or rechargeables.

We use Sanyo ENELOOP rechargeable AA cells which are guaranteed to hold 85% of their charge for 12 months if not

being used. Always recharge them after the TX has been used for any length of time.

It is most important to ensure the batteries always have plenty of charge in them when using the TX.

If the LED array only has # 2 ON, the batteries are getting low. This may result in loss of control. If you have chosen to

use Alkalines, we advise you to replace them immediately.

Inhaltsverzeichnis

Andere Eclipse Fernbedienung Handbücher

Eclipse

Eclipse RMC105 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung

Philips

Philips SBCRU130/00U Bedienungsanleitung

Philips

Philips Prestigo SRT9320 Bedienungsanleitung

Vicon

Vicon VNCTRL-1 Bedienungsanleitung