EcoBurner EcoServe Bedienungsanleitung
GLASS LID FOR ECOSERVE GN
INSTRUCTIONS FOR INSTALLATION & USE
FITTING THE STANCHION RODS AND DRAIN TUBE:
1. Glass Lid
2. Stanchion Rods X 2
3. Drain Tube
4. Drain Tube Spigot
5. Screws X 3
6. Allen Keys
7. Hinge Bracket
Thank you for purchasing this Glass Lid for the
EcoServe GN. It is an accessory used to cover dishes
of food placed on the EcoServe GN and can be
adjusted according to the height of the dish being
used. Please follow the use and care instructions to
ensure it retains its high quality finish.
FITTING THE LID TO ECOSERVE GN:
The glass lid is now ready to be fitted to the
EcoServe GN which is sold separately.
Some of the images below refer to parts of
the EcoServe GN.
CONTENTS:
8. Knurled Nuts
9. Hot Air Cover
10. Blanking Plate
8 9 10
1
3
4
5
6
2
7
1. Place the Glass Lid (1) upside down on a so surface.
2. Screw the Stanchion Rods (2) into place.
3. Use the supplied 6mm allen key (6) to tighten.
4. Push the silicone Drain Tube (3) into place on the
spigot (4) . The angled cut end should face up.
Scan here
for video
instructions
1
2
2
6
3
4
1. Remove the Blanking Plate:
Place the EcoServe GN upside down on a so
surface. Undo the two Knurled Nuts (8) and remove
the Hot Air Cover (9). Unscrew the Blanking Plate
screws using the smaller allen key supplied.
Remove the Blanking Plate (10). Save the screws in
case the blanking plate is to be refitted.
3. Fit the Lid to the Hinge Bracket:
Stand the EcoServe GN upright. Ensure both
Locking Knobs are unlocked. Slide both the
Stanchion Rods (2) into the holes in the Hinge
Bracket. Ensure the Drain Tube (3) is positioned
correctly to drain into the EcoServe GN.
Please retain this leaflet for future reference.
EcoBurner Ltd., Unit 5, Gulfstream Ave., Airside Business Park, Waterford X91RF20 Ireland
+353 51353806 www.ecoburner.com info@ecoburner.com
2b. Fit the Hinge Bracket:
Attach the Hinge Bracket (7) in place of the
Blanking Plate. Use the screws provided with the
lid (5) [note these are dierent from the Blanking
Plate screws]. Do not over-tighten the screws.
Replace the Hot Air
Cover (9) and Knurled
Nuts (8).
4. Adjust the height according to dish in use:
Open Lid. Turn both Locking Knobs anti-clockwise
to unlock the Lid. The Lid is now free to move up
and down. Place the dish to be used on the
EcoServe GN Hot Plate. Gently lower the Lid until it
is seated on or slightly above the rim of the dish.
Turn the Locking Knobs clockwise to lock the Lid
in place.
2. Fitting the Hinge Bracket:
During fitting of the Hinge Bracket, it is essential
that the EcoServe GN is raised o the table by at
least 10mm to ensure the Hinge Bracket can be
fitted correctly.
Needs to be a
small gap here
10mm
minimum
Book or similar so object
placed on the table beneath
the EcoServe GN hot plate.
2b.
Locking Knob
Drain Tube
positioned correctly
3. 4.
2.
1.
Inhaltsverzeichnis
Andere EcoBurner Küchengerät Handbücher
