EcoFlow 100 W Flexible Solar Panel Bedienungsanleitung
100 W Rigid Solar Panel
Contact Us:
ecoflow.com
NA/LA/APAC/MEA: support@ecoflow.com
EU: support.eu@ecoflow.com
AU: support.au@ecoflow.com
Contents
1Purpose
2 Disclaimer
3 General Safety Information
4 Safety Precautions
5 Installation Procedure and Precautions
5.1 Unpacking and Precautions
5.2 Pre-Installation Requirements
5.3 Installation Precautions
5.4 Bolt Installation
6 Commissioning and Troubleshooting
7 Product Specifications
8 FAQs
9 Maintenance
1
1
1
2
2
3
4
6
9
9
10
11
1
1. Purpose
2. Disclaimer
3. General Safety Information
This manual contains information about the solar energy components and their installation. Please make sure you read
and fully understand this manual before purchasing and installing the panels to ensure that you use them correctly.
Any incorrect usage may result in severe injury to the user or others, damage to the product or loss of property.
If you have any questions, please do not hesitate to contact us for further clarification and explanation.
When installing modules, installers should follow all safety precautions specified in this manual and any local
regulations. Before installing solar photovoltaic systems, installers should be familiar with the mechanical and
electrical requirements of such systems.
After reading this manual, keep it in a safe place for future reference on service and maintenance information.
This document applies to the following solar module series: EF-SG-M100
As the use of this manual as well as the conditions or methods for the installation, operation, use and maintenance
of photovoltaic (PV) products may exceed the control of EcoFlow, EcoFlow assumes no responsibility for such non-
standard installations and operations, and expressly disclaims any loss, damage, and maintenance requirements
arising therefrom or in any way related thereto.
EcoFlow shall not be liable for any infringement of third-party patents or other rights that may result from the adoption
of the installation methods, accessories, etc. that are not provided by our company during installation and use.
The product information and installation examples in this manual are provided based on EcoFlow's and our partners'
relevant knowledge and experience and are considered to be reliable; however, the restrictions and recommendations
in such information, including product specifications, do not constitute any express or implied warranty.
Before using the product, please read the User Manual and the disclaimer of liability for this product carefully.
Once you use this product, it will be deemed that you have understood, acknowledged and accepted all the
terms and contents of this document, and the user shall be responsible for their actions and all consequences
arising therefrom. EcoFlow hereby disclaims any liability for any losses due to the user's failure to use the product
according to the User Manual.
In compliance with laws and regulations, the company shall have the final right to interpret this document and all
related documents for this product. Any update, revision or termination of the contents thereof, if necessary, shall
be made without prior notice, and users may visit the ocial website of EcoFlow for the latest information on the
product.
Solar photovoltaic systems must only be installed by qualified personnel with relevant professional skills and
knowledge. All solar modules are equipped with a permanently connected junction box and 2.5 mm2(0.004 in2)
wires. Installers shall bear all risk of injury that may occur during installation, including, but not limited to, the risk of
electric shock.
When exposed to direct sunlight, a single module may generate DC voltages greater than 24 V. Exposure to DC
voltages of 24 V or higher is potentially dangerous. Arcing may occur when disconnecting wires that are connected
to the PV components exposed to sunlight. Such arcing may cause burns or a fire. Please operate with special care,
otherwise it may give rise to further issues. It is therefore important to protect yourself from electricity!
The solar modules convert solar energy into DC electricity, and they are designed for outdoor use. Modules can
be mounted on top of a fixed outdoor object, and the system designer and installer shall be responsible for the
compliance of the design of their supporting structure.
Do not attempt to disassemble the module, or remove any attached nameplates or components.
Do not apply paint, adhesives or substances that block the battery cell from light to the light-receiving surface of
the module.
Do not expose the surface of the module to amplified sunlight that is artificially centralized.
When installing systems, please observe all local, regional and national laws and statutory regulations. When
installing them on a vehicle or vessel, please observe relevant local and national laws and regulations.
2
5. Installation Procedure and Precautions
5.1 Unpacking and Precautions
Solar Panel User Manual and
Warranty Card
4. Safety Precautions
When light shines on the light-receiving surface of the solar module, the solar module will generate DC electricity
with a voltage of over 24 V. If modules are connected in series, the total voltage is equal to the sum of the voltage
of each module. If modules are connected in parallel, the total current is equal to the sum of the current of each
module.
When transporting and installing any mechanical and electrical components, please take care to keep children away
from the system and installation site.
It is recommended that the light-receiving surface of the module be completely covered with opaque material
during installation and that the positive and negative terminals be disconnected in order to prevent issues arising
from power generation.
When installing or troubleshooting for a PV system, do not wear metal rings, straps, earrings, nose rings, lip rings or
other metal devices, and only use insulated tools approved for electrical installation.
Please comply with safety instructions for all other components utilized in the system, including cables, connectors,
controllers, charge regulators, inverters, batteries and other rechargeable batteries, etc.
Use only the relevant equipment, connectors, wiring and brackets applicable to the installation of this solar module
system. Always use modules of the same type in a particular PV system. Bypass diodes have been integrated into
the junction box for all modules.
For any single module or combination of more than one module connected in series or parallel, the cross-sectional
area of the cable and the capacity of the connector must suit the maximum system short-circuit current, otherwise
the cable and connector will overheat at high currents.
DC fuses must be appropriate for the module's overcurrent protection rating.
Under normal outdoor conditions, the currents and voltages generated by the module will be dierent from those
listed in the data sheet, depending on the weather and ambient temperature. Data specified on the nameplate are
expected values under standard test conditions (STC).
Obtain information on any requirements and pre-approvals for the site, installation and inspection from the relevant
authorities prior to installation.
When installing the product on the roof of a vehicle, ensure that the roof is protected against fire: The installation
site should be free of flammable materials. The solar panel's positive and negative terminals should be fully
disconnected before installation. Only use approved insulated tools for electrical installation.
Carefully unpack the solar panel and ensure that all instructions on the package are followed. The contents are
listed as follows:
3
5.2 Pre-Installation Requirements
Ensure that modules comply with general system technical requirements and that other system components will
not damage the modules mechanically or electrically.
Modules can be connected in series to increase voltage or in parallel to increase current. In a series connection, the
positive terminal of one module is transferred to the negative terminal of the second module. In a parallel connec-
tion, the positive terminals of one module and the second module are connected, so are their negative terminals.
A series connection is shown in the diagram:
Note:
1. Do not step, walk, stand or jump on any module, as uneven stresses may impact the micro cracks on
battery cell, and ultimately the module's reliability and user experience.
2. Do not use a sharp tool to score, cut, slice, or slash the module, especially the back plate.
3. Keep all electrical contacts and connectors clean and dry.
4
5.3 Installation Precautions
All the following installation methods are for reference only, and related installation accessories need to be
purchased separately. Any system installer should ensure that the installation adheres to all specifications while
working.
The module must be mounted using the mounting holes reserved in the frame of the solar module [12 holes,
L*W:11× 7 mm (0.4 × 0.3 in)]. The most common installation method is to install the module using the four
symmetrical holes close to the center of the frame.
It is recommended that modules with the same electrical output be connected in the same series to prevent
mismatching from creating a 1+1<2 eect;
Do not block the drain hole at the bottom of the module (refer to the diagram below).
Avoid shade, as even a small amount of shade will reduce power output; ensure that the sun will be able to shine on
the module even on the shortest day of the year;
To generate the most electricity, the module should face directly south if it is in the Northern Hemisphere and face
directly north if it is in the Southern Hemisphere. For details on the best elevation angle for the installation, refer
to the standard PV installation guide of your locality or the installation angle requirements of a well-known solar
installer or system integrator.
A parallel connection is shown in the diagram:
5
As shown below:
Note:
1. The holes at the center of each long edge are used for grounding.
2. Modules should be securely mounted to withstand all expected loads, including wind and snow loads.
3. The gap between modules should be 12.7 mm (0.5 in) or larger.
Drain Hole
Mounting Hole
Grounding Hole
Nameplate Sticker
(SN Code Sticker)
Ventilation Hole
Each module has two labels that provide the following information:
NameplateSticker: Provides information on the product type, and the electrical parameters, weight, dimensions,
etc., measured under standard test conditions.
SN Code Sticker: Each module has a unique serial number.
Note: Do not remove any labels from the solar panel; removal of any labels voids the product warranty policy
from EcoFlow.
6
5.4 Bolt Installation
a. You must use the M6 stainless steel bolt, nut and washer, as well as the mounting hole on the rear side of the
module's frame.
b. Use suitable corrosion-resistant material for fastening, which should be made from stainless steel.
c. Do not drill holes in or modify the module's frame as this will void the warranty.
d. Each module must be securely mounted at four or more points in opposite directions.
e. When installing on the roof or body of a vehicle, be sure to leave a gap between the solar panel and the roof
or body to facilitate airflow and heat dissipation.
The steps are as follows:
1. Use a manual glue gun to apply the structural adhesive to the corresponding area (the surface contacting with
the frame) of the z-shaped bracket.
Gluing Area
Z-shaped
bracket x4
Installation requires the use of a special bolt kit (purchased separately), which includes the following items:
Four z-shaped brackets, four M6 hex bolts (with nuts), four M6 large washers, four M6 flat washers, four M6
spring washers, and eight hex self-drilling screws [5.5*38 mm (0.2*1.5 in)]
Hex Bolt (with Nut) x4
M6 Flat
Washer x4
M6 Large
Washer x4
M6 Spring
Washer x4 Hex Self-Drilling
Screw x8
7
3. Then place the large washer, and tighten the nut.
Sectional
View
2. Place the z-shaped bracket in the corresponding position and install the M6 hex bolt, M6 flat washer and M6
spring washer.
Andere Handbücher für 100 W Flexible Solar Panel
1
Inhaltsverzeichnis
Andere EcoFlow Solarpanel Handbücher
EcoFlow
EcoFlow 110W Bedienungsanleitung
EcoFlow
EcoFlow 110W Bedienungsanleitung
EcoFlow
EcoFlow EF-Fold-P60-04 Bedienungsanleitung
EcoFlow
EcoFlow 110W Bedienungsanleitung
EcoFlow
EcoFlow 400W Bedienungsanleitung
EcoFlow
EcoFlow 160W Bedienungsanleitung
EcoFlow
EcoFlow 400W Bedienungsanleitung
EcoFlow
EcoFlow River 600 Bedienungsanleitung
EcoFlow
EcoFlow RIVER Series Bedienungsanleitung
EcoFlow
EcoFlow 100 W Flexible Solar Panel Bedienungsanleitung
