Ecosoft CROSS 90 Benutzerhandbuch
Installer and user guide for CROSS 90 direct ow
reverse osmosis lter
Інструкція з підключення та експлуатації
прямоточного фільтру зворотного осмосу CROSS 90
2
INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER
This manual is the intellectual property of Ecoso. Copying and reprinng is prohibited. © 2023
CONTENTS
1. Purpose of the product 3
2. Specicaons and components 4
2.1 Specicaons and requirements 4
2.2 Water quality 5
2.2.1 Supply water quality requirements 5
2.2.2 Water quality aer lter 5
2.3 Reverse osmosis lter components 6
2.4 Reverse osmosis lter indicators 7
3. Filter installaon 7
3.1 Before commencing installaon 7
3.2 Connecon diagram 8
3.3 Installaon procedure 8
3.4 First me use 13
4. Steps aer installaon 13
5. Usage 14
5.1 Parts of the lter and their recommended change out rates 14
5.2 The procedure for cartridges replacing 14
5.3 Filter lifeme display 15
5.4 Water quality display 16
5.5 System operaon modes 16
5.6 SMART features 17
6. Sanizaon of reverse osmosis lter 18
7. Troubleshoong 20
8. Service record 21
9. Environmental and health safety 22
10. Purchasing 22
11. Transportaon and storage 23
12. Warranty 23
3
EN
INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER
This manual is the intellectual property of Ecoso. Copying and reprinng is prohibited. © 2023
DEAR CUSTOMER!
1. PURPOSE OF THE PRODUCT
Thank you for choosing our products.
We want you and your family to enjoy clean drinking water. With Ecoso lter you will forget
the trouble of using large boles. Pure spring water for drinking, cooking and making drinks will
always be at hand. Please read this instrucon manual and check validity of the warranty card
before using the system.
Reverse osmosis is by far the most advanced technology of water puricaon in use today. Special
semipermeable membrane structure similar in its properes to the membrane of a living cell
is capable of purifying drinking water from virtually all harmful impuries (see Figure 1). The
membrane can be conceived of as having ny pores, 200 mes smaller than viruses and 4000
mes smaller than bacteria. Domesc water lters with reverse osmosis membranes harness the
principle of body’s metabolism on a cellular level. Only molecules of certain size can penetrate
cellular membrane.
Direct ow reverse osmosis lter CROSS 90 is a four-stage in three steps ltraon unit with
three cartridges funconing as follows (see secon (2.3) for reference numbers). Filter rack is
connected to cold water supply with feed water adapter (4). White tube (3/8”) carries water from
feed valve through low pressure switch and inlet solenoid valve to the CF lter cartridge. Incoming
water then passes through pre-lter cartridge (7). Pre-lter cartridge is a complex cartridge with
(2) stages inside. It is designed to remove solids (such as rust, sand, silt, etc), residual chlorine,
and organochlorines from water. Aer undergoing pre-treatment steps in the pre-lter, water
enters into the third (and the most important) stage: reverse osmosis membrane (7) contained in
a cartridge RO. One of the two outlets supplies puried water (permeate), and the other carries
away water with rejected impuries (concentrate). The membrane puries water at the molecular
level by passing through its pores only the water molecules and the molecules of dissolved oxygen.
Tap water under
pressure
Figure 1
Molecules of smaller
size, pure water
Larger molecules
Concentrate
for disposal
Membrane
Water
molecules
4
INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER
This manual is the intellectual property of Ecoso. Copying and reprinng is prohibited. © 2023
1. PURPOSE OF THE PRODUCT
№ Parameter Value
1Main pressure, bar 1-4 *
2Feed water temperature, °C +5…+30**
3Flow capacity, l/min 1,5
4Electrical rang 230 V, 50 Hz
5Weight of the system, kg 11
6Ambient temperature, °C +5…+40
7Water supply connecon ½″ thread
8Filter dimensions, H × W × D, mm 458 x 140 x 435
2. SPECIFICATIONS AND COMPONENTS
2.1 SPECIFICATIONS AND REQUIREMENTS
Inside the membrane, water is separated into two streams: concentrate, which is discharged into
drain, and permeate, which enters next step – post-lter (7).
Aer opening the puried water valve (3), the pressure in the system drops and the high pressure
switch is acvated, opening the inlet valve and starng the pump, automacally resuming the
ow of water through the pretreatment cartridge to the membrane. Aer opening the puried
water valve (3), the pressure in the system drops and the high pressure switch is acvated,
opening the inlet valve and starng the pump, automacally resuming the ow of water through
the pretreatment cartridge to the membrane. The puried water aer the membrane enters
the fourth stage of puricaon — the CB carbon post-lter, designed for nal water puricaon.
The puried water aer the membrane enters the fourth stage of puricaon — the CB carbon
post-lter, designed for nal water puricaon. It contains extruded acvated carbon. This lter
improves the taste and smell of the puried water. This lter is direct-ow, so no water storage
tank is required. With a capacity of 600 GPD (90 l/h), it takes only 8 seconds to ll a 200 ml glass.
* If supply water pressure is below required value, purchase pumped model or t your exisng
lter with booster pump. If the pressure in the water system is above the limit, it is necessary to
install a pressure regulator on the main pipe. If pressure in tank bladder is outside this range, it is
necessary to pump up or release the pressure unl it conforms to the requirement.
** If supply water temperature is up in the range of +20…+30 °C, rejecon of impuries will be
decreased and system capacity increased, bringing about an increase in TDS. Using the product
with supply water temperature in excess of +30 °C is not recommended.
5
EN
INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER
This manual is the intellectual property of Ecoso. Copying and reprinng is prohibited. © 2023
№ Index Value**
1pH 6.5-8.5
2TDS <1500 ppm
3Hardness <500 ppm CaCO3
(<28 °dH)
4Free chlorine <0.5 ppm
5Iron <0.3 ppm
№ Index Value
1pH 5.5-6.5
2TDS 5-15 ppm
3Calcium <2 ppm
4Magnesium <1 ppm
5Sodium + Potassium <5 ppm
№ Index Value**
6Manganese <0.1 ppm
7Chemical oxygen
demand <5 ppm O2
8Total bacterial count
(TBC) <50 CFU/mL
9E. coli ter <3
2. SPECIFICATIONS AND COMPONENTS
2.2 WATER QUALITY
2.2.1 SUPPLY WATER QUALITY REQUIREMENTS*
2.2.2 WATER QUALITY AFTER FILTER*
Do not use with water that is microbiologically unsafe or of unknown quality without adequate
disinfecon before or aer the system.
* If water supply does not meet the requirements, service life of membrane and/or pre-lter
cartridges may be shortened.
** If your home is supplied with raw well water, perform laboratory test of your water before
in- stalling a reverse osmosis lter. If any of your water indices exceed the limit, consider using a
water treatment system to correct supply water quality. Refer to water treatment specialists or
companies for advice and proper equipment selecon.
* Values are determined under the following
condions: temperature of supply water is
25 °C, supply water quality and operaon
condions correspond to manufacturer’s
requirements.
6
INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER
This manual is the intellectual property of Ecoso. Copying and reprinng is prohibited. © 2023
2. SPECIFICATIONS AND COMPONENTS
1) Filter rack
4) Feed water
adapter with valve
7) Set of cartridges
CF - CPVDFRO
RO - CSVRO600DFRO
CB - CHVCBDFRO
2) Power adaptor 3) Drinking
water faucet
6) Drain saddle5) Set of colored tubes
2.3 REVERSE OSMOSIS FILTER COMPONENTS
The manufacturer reserves the right
to modify product design or specic
components if such modicaon does
not entail deterioraon of consumer
properes of the product.
7
EN
INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER
This manual is the intellectual property of Ecoso. Copying and reprinng is prohibited. © 2023
2. SPECIFICATIONS AND COMPONENTS
3. FILTER INSTALLATION
2.4 REVERSE OSMOSIS FILTER INDICATORS
1 – System performance indicator - making water indicaon, water quality indicaon, faults
indicaon, ushing indicaon
2 – RO replacement lter lifeme indicator
3 – CB replacement lter lifeme indicator
4 – CF replacement lter lifeme indicator
5 – Faucet indicator - making water indicaon, faults indicaon, replacement indicaon, ushing
indicaon
5
Before installing a domesc reverse osmosis lter please carefully read this instrucon.
This system must be installed in compliance with local codes.
3.1 BEFORE COMMENCING INSTALLATION
1) Check that all parts are in the package. Do not open the plasc bags with lter parts before you
make sure everything is in place to be able to return faulty/incomplete package.
2) Check conformity of your local variables to requirements specicaons:
Main pressure* Supply water temperature*
Check water pressure at mains before install-
ing the product. Compare to the requirements
in paragraph (2.1).
Check temperature of supply water. Compare
to the requirements in paragraph (2.1).
*Refer to paragraph 2.1 for recommended measures in case any of the above variables
does not meet the requirements.
1
2
3
4
8
INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER
This manual is the intellectual property of Ecoso. Copying and reprinng is prohibited. © 2023
— verify that your product is as specied in paragraph 2.1;
— verify that your supply water quality** meets the requirements in paragraph 2.2.
**If supply water quality does not meet the requirements, it is necessary to consult with a
water treatment specialist.
3) Before installing the system, make sure there is enough space for the lter rack under the sink.
4) Electrical safety noce: This appliance should be connected into a circuit with an RCB installed.
Please note voltage requirements.
5) Install the system per the guidelines of this manual.
6) The unit is to be supplied with single-phase 230 VAC, 50 Hz electrical power.
The unit is supplied with power cord and can be connected to a properly installed IEC 60884-1
compliant socket. Electrical specicaon of the unit can be found on manufacturer’s factory
scker. That system and installaon must comply with state and local laws and regulaons.
3.2 СONNECTION DIAGRAM
3.3 INSTALLATION PROCEDURE
Wash your hands thoroughly with an-bacterial soap before handling tubes, cartridges, and
membrane.
This system should desirably be installed in places protected from direct sunlight and away
from heang appliances.
3. FILTER INSTALLATION
3/8” White pipe
1/4” Red pipe
1/4” White pipe
9
EN
INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER
This manual is the intellectual property of Ecoso. Copying and reprinng is prohibited. © 2023
1. Remove the reverse osmosis system from its packaging and check the equipment.
2. Shut o water supply in your kitchen or whole home and open water tap where you are about
to install the system (on your kitchen sink) for 1 minute to relieve pressure in the system, and
then close it.
3. Screw the feed water adapter with valve (4) into the cold water plumbing.
Connecons size is selected to t most common size ½ inch pipe. If your pipe is of another size,
prepare an appropriate adapter.
4. Unscrew the compression nut from the feed valve (4) and put it on the 3/8” white tube. Push
the white tube on the end of feed valve’s ng and screw on the compression nut. Connect the
free end of the 3/8” white tube with the quick connect ng “Inlet” on the connecon panel of
the rack. Insert the 3/8“ quick coupling lock plate between the quick connect and the claw of the
water inlet pipe.
3/8” PE pipe in
proper length
3/8” quick coupling
lock plate
3. FILTER INSTALLATION
10
INSTALLER AND USER GUIDE FOR CROSS 90 DIRECT FLOW REVERSE OSMOSIS FILTER
This manual is the intellectual property of Ecoso. Copying and reprinng is prohibited. © 2023
5. Connect the drain saddle (6) with drain pipe from
the kitchen sink. The drain saddle is compable
with most standard drain pipes. Drill a hole of 5.0
mm (0.2”) diameter in the kitchen sink drain pipe,
apply rubber gasket with scky base (included in
the package).
Install the drain saddle (6) on the drain pipe over
the hole. Tighten screws on drain saddle with a
screwdriver. Insert red tube into the connecon on
the clamp. Connect the other end of the red tube
with concentrate outlet “Waste” on the connecon
panel of the rack. Insert 1/4” quick coupling lock
plate between quick coupling and jack catch of pipe.
6. Connect one end of 1/4” white tube to
the “Filtered” output on the connecon
panel of the rack. Insert the 1/4”quick
coupling lock plate between the quick
connect and the claw of the water inlet
pipe.
CAUTION! If RO systems do not use air gap faucets, it is required that they be plumbed in with
a physical air gap between the waste water outlet and the drain. This is so if the drain backs
up, sewage will not push up into the RO system.
1/4” quick coupling
lock plate
1/4” wihte PE pipe in proper lenght
Sewage outlet
1/4” quick coupling
lock plate
1/4” wihte PE pipe
in proper lenght
3. FILTER INSTALLATION
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere Ecosoft Wasserfiltersystem Handbücher
Ecosoft
Ecosoft FPV12ECO Bedienungsanleitung
Ecosoft
Ecosoft FK1252CEMIXC Bedienungsanleitung
Ecosoft
Ecosoft Dewberry Bedienungsanleitung
Ecosoft
Ecosoft FK1035CIMIXP Bedienungsanleitung
Ecosoft
Ecosoft MO36000PECO Benutzerhandbuch
Ecosoft
Ecosoft FK Series Bedienungsanleitung
Ecosoft
Ecosoft WS1 DV Bedienungsanleitung
Ecosoft
Ecosoft MO6500BWTSS Bedienungsanleitung
Ecosoft
Ecosoft AquaPoint Bedienungsanleitung
Ecosoft
Ecosoft SENSE Benutzerhandbuch
Ecosoft
Ecosoft WS1 CE Bedienungsanleitung
Ecosoft
Ecosoft 3-STAGE Bedienungsanleitung
Ecosoft
Ecosoft Robust Bedienungsanleitung
Ecosoft
Ecosoft MO-12 Bedienungsanleitung
Ecosoft
Ecosoft FU1054TWIN Bedienungsanleitung
Ecosoft
Ecosoft FPA Series Bedienungsanleitung
Ecosoft
Ecosoft AquaPoint FPV24520ECO Bedienungsanleitung
Ecosoft
Ecosoft LUNA Montageanleitung
Ecosoft
Ecosoft RO 5-36 Benutzerhandbuch
Ecosoft
Ecosoft FK1252CEMIXA Bedienungsanleitung
Beliebte Wasserfiltersystem Handbücher anderer Marken
Gaggenau
Gaggenau BRITA INTENZA 467873 Bedienungsanleitung
Brita
Brita SAFF-100 Bedienungsanleitung
HEISSNER
HEISSNER FPU24000-00 Bedienungsanleitung
BGS technic
BGS technic 1518 Bedienungsanleitung
Reverse Osmosis
Reverse Osmosis RF Series Bedienungsanleitung
ubbink
ubbink Filtramax Series Bedienungsanleitung