Ecovolt JTB Series Kurzanleitung
JTB Electric Radiators Installation
and Operational Manual
JT4B and JT6B versions
JT4B Radiator
JT6B Radiator
www.ecovolt.ie
2
-Read the instruction manual carefully
before commencing the installation
-Installation should be completed
by a competent person
-All electrical work to be completed
-Please dispose the package properly.
Towel Rail Installation
1. Drill
2. Screwdriver(s)
3. Spirit level
4. Cable cutters
5. Measuring tape
+ penc
JTB Electric Radiators
Installation and Operational Manual
Tools Required
to complete the installation
3
Installing the female wall brackets
Using a measuring tape, spirit level and pencil, mark the wall where the
4 female brackets are to be positioned. It is important to line the male
spigot bracket attached to the heater to your markings. Using the drill, drill
4 holes in the wall and insert wall plugs. Tighten the female brackets to the
wall using the screws provided as illustrated below.
4
Inserting the electrical element into the heater
Remove the element from the packaging and insert it into the bottom
right corner threaded end. Tighten with a tool. If you are using the digital
programmer, attach the programmer and secure using the small
screw supplied ensuring the spade connections are secured and tight.
Fixing the heater to the female brackets
Line up the male spigot brackets on the back of the heater and insert them
into the female brackets. Using the screwdriver and the security bolts,
secure the heater and ensure the bolt is tight. The heater is now secure to
the wall.
5
Connecting the heater to the 230V electricity supply
WARNING: DO NOT TURN POWER ON IF THE HEATER IS EMPTY!
Note: This should only be done by a qualied electrician.
With the electricity supply turned off and isolated, connect the live
wire (brown) to the live terminal (L) of the isolating switch. Connect
the neutral wire (blue) to the neutral terminal (N) of the isolating
switch. Connect the earth wire (green/yellow) into the earth terminal
(E) of the isolating switch. When all 3 wires have been terminated
to the 230V supply switch is it then safe to turn on the heater.
The heater will now begin to heat up and will take approx. 30 minutes
to reach uniform surface temperature.
Filling the heater with water
- JT4B – Pour 330ml of water into the heater
- JT6B – Pour 450ml of water into the heater
Fit and tighten the 4 valve locks into the sides of the heater. Fill the heater
valve to the top of the heater as shown below
6
LCD Digital
Thermostat Manual
The following information is intended only for the digital thermostat
oC
oC
g) Programming mode
comfort-1, comfort-2
1. General information:
LCD Digital Thermostat Description
2. Panel display:
3.1 Comfort mode: Setting the temperature in the daytime,
o30oC
3. Functions and heating modes:
3.2 Economy mode: Setting the temperature in the night,
o30oC. The Max temperature
shall not exceed the comfort temperature
3.3 Defrost mode: oC,
3.5 Timing setting:
Icon
3.4 Timing mode: Timing function, Icon
3.6 Programming modes (Class II only): Six modes available,
1. Comfort mode
2. Comfort-1 mode
3. Comfort-2 mode
4. Economy mode
5. Defrost mode
6. Power off mode, Icon
3.7 Child lock function: This will disable all buttons. Icon
3.8 Heating function: Working status, Icon the heater is on
3.9 Button function:
ff button
Function button
Plus button
Minus button
8
4.1 Start up: Press to turn on the heater. All buttons are invalid the
heater is on
4. Mode operation instructions:
4.2 Change heating modes: The factory default setting when the heater
is turned on is comfort mode, press to switch the mode to the following,
comfort mode →economy mode →defrost mode →timing mode →
programming mode
4.2.1 Comfort mode : The default temperature is 19oC
As
Press or to set the temperature, press to increase the
temperature, press to reduce the temperature in 0.5oC steps, hold
or down to speed the temperature adjustment process.
4.2.2 Economy mode : The default temperature is 15.5oC
As
Press or to set the temperature, press to increase the
temperature, press to reduce the temperature in 0.5oC steps,
Press or 1s to speed the temperature adjustment scope.
4.2.3 Defrost mode : oC
As
9
4.2.4 Timing mode : Setting the timing mode for the heater.
4.2.4.1. Time setting:
When enter the timin
Press , to adjust the time.
Press
the adjustment speed.
Note: If there is no activity in 30 seconds, the timing setting will exit and
return to the previous screen
4.2.4.2. Week setting:
Once the time setting is completed ,press to adjust the week setting as
Press or to adjust.
01=Monday, 02=Tuesday, 03=Wednesday, 04=Thursday, 05=Friday,
06=SaturdaySunday
It will exit the week settings if there is no activity within 30 seconds.
10
4.2.4.3. Daily programming setting:
After completing the week setting, press to enter the daily
programming setting.
Press or to set the daily programming setting.
(P1-P5), comfort mode is indicated by( )in the time axis.
Economy mode is indicated by in the time axis.
these times).
times outside these times)
mode all other times outside these times)
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Ecovolt Heizung Handbücher
Beliebte Heizung Handbücher anderer Marken
Empire Heating Systems
Empire Heating Systems WCC65 Bedienungsanleitung
Wetekom
Wetekom 92 86 43 Bedienungsanleitung
Desa
Desa SPC170-F Bedienungsanleitung
Watlow
Watlow Watrod Electric Tubular Heaters Bedienungsanleitung
Haverland
Haverland ECO-DRY GPS Series Stücklistenhandbuch
Stelpro
Stelpro ASILVC2060 Series Bedienungsanleitung