ECR International UTICA BOILERS TRIFIRE II Series Gebrauchsanweisung

P/N# 240009350, Rev. E [12/2014]

TRIFIRE SERIES II

High E󱐰ciency

Oil Fired Hot Water Boiler

INSTALLATION, OPERATION &

MAINTENANCE MANUAL

An ISO 9001-2008 Certified Company

Manufactured by:

ECR International, Inc.

2201 Dwyer Avenue, Utica NY 13501

web site: www.ecrinternational.com

Models

TRB4075

TRB4095

TRB4110

TRB5100

TRB5115

TRB5135

TRB6130

TRB6145

TRB6165

TRB7165

TRB7180

TRB7190

TRIFIRE OIL-FIRED CAST IRON HOT WATER BOILER

Per Energy Star specications, AFUE

is rounded to the nearest whole

percentage point. As such, these

products qualify for Energy Star.

Check our website frequently for updates: www.ecrinternational.com

Information and specications outlined in this manual in effect at the

time of printing of this manual. ECR International reserves the right to

discontinue, change specications or system design at any time without

notice and without incurring any obligation, whatsoever.

Models

TRB5100

TRB6130

DIMENSIONS

Sections

Flue Size

Inches

(cm)

Dimension

Inches

(cm)

4 5 (13) 18 3/8 (46)

5 5 (13) 21 5/8 (56)

6 5 (13) 24 7/8 (64)

7 6 (15) 28 1/8 (72)

1 - Introduction.............................................................................................................. 5

2 - Safety Information..................................................................................................... 6

3 - Before You Start ........................................................................................................ 7

4 - Ratings & Capacities .................................................................................................. 8

5 - Locating The Boiler .................................................................................................... 9

6 - Installation Requirements ......................................................................................... 10

7 - Fresh Air For Combustion.......................................................................................... 11

8 - Boiler Assembly....................................................................................................... 13

9 - Boiler System Piping ................................................................................................ 18

10 - Hydronic Piping ..................................................................................................... 19

11 - Fuel Supply Piping ................................................................................................. 32

12 - Antifreeze In The System ....................................................................................... 33

13 - Electrical Connections............................................................................................. 34

14 - Chimney And Venting Connections ........................................................................... 35

15 - Filling Boiler .......................................................................................................... 38

16 - Operating The Boiler - System Start-Up ................................................................... 39

17 - Oil Burner, Nozzle, & Air Settings ............................................................................. 46

18 - Maintenance ......................................................................................................... 52

19 - Oil Boiler /Burner Cleaning Instructions .................................................................... 54

20 - Troubleshooting ..................................................................................................... 56

21 - Equipment And Accessories .... ................................................................................58

Parts List..................................... ................................................................................62

Warranty ..................................... ................................................................................68

Check Out Certicate..................... ...............................................................................70

TABLE OF CONTENTS

1.1 OIL FIRED BOILERS

Boiler is low pressure, sectional cast iron constructed

and tested for maximum working pressure of 65 psi in

accordance with A.S.M.E. (American Society of Mechanical

Engineers) Section IV Standards for cast iron heating

boilers. Capacity rated in accordance with AHRI (Hydronics

Institute).

Boiler is pressure red natural draft (chimney vented)

oil red hot water boiler comprised of cast iron sections,

available with 4, 5, 6 or 7 sections. Sections are held

together by push nipples and threaded rods.

4,5 and some 6 section boilers may be factory equipped for

direct vent installations. Direct vent instructions are cov-

ered in a separate supplemental instructions document.

Boiler models are capable of ring #2 fuel oil from 0.75

gph up to 1.90 gph.

Boilers include -

• Limit, 220° F maximum, operating control with integral

low water cut off.

• Temperature and pressure gauge

• 30 psi relief valve

• Drain valve

1 - INTRODUCTION

WARNING

Installations of boilers and venting shall be done

only by a qualied expert and in accordance with

this manual. Installing or venting a boiler or any

other oil appliance with improper methods or

materials may result in serious injury or death due

to re or to asphyxiation from poisonous gases

such as carbon monoxide which is odorless and

invisible.

NOTICE

Surface rust on cast iron sections may be attributed

to manufacturing process as well as condensation

during storage. Surface rust is normal and does not

affect performance or life of boiler.

2 - SAFETY INFORMATION

2.1 General

Boiler installation shall be completed by qualied agency.

WARNING

Fire, explosion, asphyxiation and electrical shock

hazard. Improper installation could result in death

or serious injury. Read this manual and understand

all requirements before beginning installation.

WARNING

Modication, substitution or elimination of factory

equipped, supplied or specied components could

result in death or serious injury.

WARNING

Improper installation, adjustment, alteration, service

or maintenance could result in death or serious

injury.

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

DANGER

Indicates a hazardous situation which, if not avoided,

WILL result in death or serious injury

This is the safety alert symbol. Symbol alerts you to

potential personal injury hazards. Obey all safety messages

following this symbol to avoid possible injury or death.

2.2 Become Familiar With Symbols Identifying

Potential Hazards.

IMPORTANT: Read the following instructions

COMPLETELY before installing!!

2.3 Installation shall conform to requirements of

authority having jurisdiction or in absence of such

requirements to ANSI/NFPA 31, “Installation of Oil

Burning Equipment”. In Canada, Current Edition

of Canadian Standards Association CSA B139,

Installation Code for Oil Burning Equipment” for

recommended installation practices.

Such applicable

requirements take precedence over general

instructions of this manual.

2.4 Current Edition of American National Standard

ANSI/NFPA 211 “Chimneys, Fireplaces, Vents and

Solid Fuel Burning Appliances” for venting.

2.5 Where required by authority having jurisdiction,

installation shall conform to Standard for Controls

and Safety Devices for Automatically Fired Boilers,

ANSI/ASME CSD-1.

Additional manual reset low water cutoff and manual reset

high limit may be required.

2.6 Requirements for Commonwealth of

Massachusetts:

Boiler installation must conform to Commonwealth of

Massachusetts code 248 CMR which includes but is not

limited to:

• Installation by licensed plumber or gas tter.

WARNING

Construction materials of appliance and products

of combustion and fuel contain alumina, silica,

heavy metals, carbon monoxide, nitrogen

oxides, aldehydes and /or other toxic or harmful

substances which can cause death or serious injury

and which are known to the State of California to

cause cancer, birth defects and other reproductive

harm. Always use proper safety clothing,

respirators and equipment when servicing or

working nearby the appliance.

WARNING

Product contains berglass wool and refractory

ceramic bers. Possible cancer hazard. May cause

irritation to skin, eyes and respiratory tract. To

avoid this hazard, wear a dust mask and gloves

when handling berglass and ceramic bers.

NOTICE

Used to address practices not related to personal

injury.

3.1 Installation and Operation

Do not operate unit if any control, switch, components

or devices have been underwater or subject to water

damage.

Before servicing, allow boiler to cool. Always shut off any

electricity and oil supply to boiler when working on it.

Inspect oil line and connections for leaks.

Verify oil burner nozzle is proper size. Over-ring will

result in early failure of boiler sections, and result in a

potentially dangerous situation.

Never vent boiler into enclosed space. Always vent to

the outside. Never vent to another room or inside a

building.

Verify adequate air supply for complete combustion.

Relief valve automatically lifts open when system

pressure exceeds 30 psi. Before installing relief valve

read manufacturer’s instructions. Pipe relief valve to a

safe location. Check with authorities having jurisdiction.

Consider system total water volume, temperature,

initial ll pressure and arrangement when sizing and

installing expansion tank. Improperly installed and

sized expansion tank may result in frequent lifting of

relief valve or other heating system problems. Follow

expansion tank manufacturer guidelines for installation,

and sizing.

Boiler manufacturer recommends initial ll pressure of

10-12 psi. For higher ll pressures increase expansion

tank’s air charge to match ll pressure.

10.

Purge heating system of air and gases is critical for

proper circulation and quiet performance. Once the air

is purged, for boiler installations using oat type vents,

air vents should be closed for normal operation. If air

is heard or noticed by loss of heat, purge system and

open vents for short period of time.

3.2 Prior To Installing The Boiler

• Verify you have selected right size boiler with proper

capacity. AHRI rating of boiler selected should be greater

than or equal to calculated peak heating load (heat loss)

for building or area(s) served by boiler and associated

hot water heating systems. Use heat loss calculations

based on approved methods. See Figure 1, Page 8

• Boiler must be supplied with proper oil supply and oil

piping, sufcient fresh combustion air, and suitable

electrical supply.

• Connect boiler to suitable venting and piping systems

adequate to distribute heating load.

• Installation is not complete unless pressure relief valve

is installed 3/4” tapping located in supply piping.

• Thermostat must be properly located and installed

• Failure to pipe boiler correctly may result in excessive

noise or other related problems.

Existing Water System Evaluation

A good system will prevent oxygen contamination of boiler

water.

Causes of oxygen contamination may be:

A. Addition of excessive make up water as a result of

leaks.

B. Absorption through open tanks and ttings.

C. Oxygen permeable materials in the distribution

system.

To insure long product life, oxygen sources must be

eliminated.

Take the following measures:

A. Repair system leaks.

B. Eliminate open tanks from the system.

C. Eliminate and/or repair ttings which allow oxygen

absorption.

D. Use non-permeable materials in the heating system.

3 - BEFORE YOU START

GPH = U.S. Gallons per Hour

Mbh = 1000 Btu (British thermal units) per hour.

psi = Pounds per square inch

*MAWP = Maximum allowable working pressure. This low pressure oil red hot water boiler is constructed and

hydrostatically tested for maximum working pressure of 65 psi in accordance with the latest revision of the A.S.M.E.

(American Society of Mechanical Engineers) Boiler and Pressure Vessel Code Section IV Standards for heating boilers.

AFUE= Annual Fuel Utilization Efciency

Heating Capacity and AFUE based on 13.1% CO2(13.5% CO2 at 0.95 GPH and 1.10 GPH), -0.02” w.c. draft in breech, and

# 1 smoke or less. Testing is done in accordance with U.S. DOE (Department of Energy) test procedure.

Heating Capacity indicates amount of heat available after subtracting losses up the stack. Remaining heat is available

to heat water. Small portion is heat from jacket and surfaces of boiler and this heat stays in structure. Net AHRI rating

represents portion of remaining heat applied to heat radiation or terminal units (i.e. nned tube baseboard, cast iron

radiators, radiant oor, etc.). Difference between Heating Capacity and Net AHRI Rating, called piping and pickup

allowance, establishes reserve for heating volume of water in system and offsetting heat losses from system piping. Net

AHRI ratings shown are based on piping and pickup factor of 15% in accordance with AHRI Standard as published by

Hydronics Institute.

Net AHRI rating of boiler selected should be greater than or equal to calculated peak heating load (heat loss) for building

or area(s) served by boiler and associated hot water heating systems. Consult manufacturer before selecting boiler for

installations having unusual piping and pickup requirements.

4 - RATINGS & CAPACITIES

Table 1 RATINGS & CAPACITIES

OIL-FIRED HOT WATER BOILERS

Number

Sections

Firing

Rate

[GPH]

Input

[Mbh]

Heating

Capacity

[Mbh]

Net

AHRI

Rating

[Mbh]

*MAWP

Water

[psi]

AFUE

[%]

Min. relief

Valve

Capacity

[Mbh]

Max.

Water

Temp

[°F]

Chimney

Liner Size

Round

[Inches]

Chimney

Liner

Size

[Square

Inches]

Flue

Size

[Inches]

4 0.75 105 91 79 65 86.0 91 250 6 6 3/4 5

4 0.95 133 114 99 65 85.0 115 250 6 6 3/4 5

4 1.10 154 132 115 65 84.0 132 250 6 6 3/4 5

5 1.00 140 122 106 65 86.5 122 250 6 6 3/4 5

5 1.15 161 139 121 65 85.0 139 250 6 6 3/4 5

5 1.35 189 161 140 65 84.0 161 250 7 6 3/4 5

6 1.30 182 159 138 65 86.5 159 250 6 6 3/4 5

6 1.45 203 176 153 65 85.0 176 250 7 6 3/4 5

6 1.65 231 198 172 65 84.0 198 250 7 6 3/4 5

7 1.65 231 201 175 65 86.0 201 250 7 6 3/4 6

7 1.80 252 217 189 65 85.0 217 250 7 6 3/4 6

7 1.90 266 228 198 65 84.0 227 250 8 6 3/4 6

Boiler is suitable for installation on combustible

ooring. Do not install boiler on carpeting.

Locate boiler in front of nal position before removing

crate.

Locate unit so vent pipe connection to chimney will be

short and direct.

For basement installation, provide solid elevated base,

such as concrete, if oor is not level, or if water may be

encountered on oor around boiler.

Provide recommended service clearance, if applicable,

as follows:

• Clearance from Jacket Front Panel

24” for servicing burner

• Clearance from Jacket Side Panels

24” for burner swing door, if opened fully with burner

mounted, otherwise 2” with burner removed.

• Clearance From Jacket Rear Panel

12” minimum for rear smoke box cleaning. (Note:

this dimension will also be controlled by horizontal to

vertical to horizontal smoke pipe arrangement. See

Figure 1

Minimum clearances to combustible material see

Figure 1 and Table 2.

Table 2 - BOILER CLEARANCES

Unit Combustible

Clearance

Accessibility,

Cleaning,

and Servicing

Top 12” (32 cm) 24” (61 cm)

Right Side 2” (5 cm) 24” (61 cm)

Left Side 2” (5 cm) 24” (61 cm)

Floor Combustible No Requirement

Front 17” (43 cm) 24” (61 cm)

Back See Flue 18” (46 cm)

Flue 9” (23 cm) 9” (23 cm)

All distances measured from the boiler jacket or ue.

Fresh air for combustion and ventilation must be avail-

able at boiler. Ventilating and combustion air must

enter boiler room without restrictions.

Installation shall conform to requirements of authority

having jurisdiction or in absence of such requirements

in United States, follow NFPA 31 Installation of Oil

Burning Equipment. In Canada, use CSA B 139, latest

revision.

Clearance to venting is for single wall ue pipe. If Type

L vent is used, clearance may be reduced to minimum

required by vent pipe manufacturer.

15”

Figure 1 - Clearances to Combustible Construction

5 - LOCATING THE BOILER

WARNING

Fire hazard. Do not be install on carpeting. Failure

to follow these instructions could result in death or

serious injury.

6 - INSTALLATION REQUIREMENTS

NOTICE

Shut off manual fuel supply valve if burner is shut

down for extended period of time.

Figure 2 - General Requirements For A Typical Installation

LIMIT

RELIEF

VALVE

CHECK LOCAL CODES FOR

MAXIMUM DISTANCE FROM

FLOOR, OR OTHER ALLOWABLE

SAFE POINT OF DISCHARGE.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ECR International Kessel Handbücher

ECR International

ECR International Green Mountain GMHB125 Gebrauchsanweisung

ECR International

ECR International Dunkirk DCC-150F Leitfaden

ECR International

ECR International Dunkirk DMG-240 Gebrauchsanweisung

ECR International

ECR International UTICA BOILERS MAC-150 Gebrauchsanweisung

ECR International

ECR International CCB-150 Gebrauchsanweisung

ECR International

ECR International Utica Boilers UCS-380 Gebrauchsanweisung

ECR International

ECR International GreenMountain GMGS075E Gebrauchsanweisung

ECR International

ECR International B Series Bedienungsanleitung

ECR International

ECR International Dunkirk WPSB II Series Gebrauchsanweisung

ECR International

ECR International 95M-200 Bedienungsanleitung

ECR International

ECR International UTICA HEATING UH15C Gebrauchsanweisung

ECR International

ECR International Olsen OQ95M-200 Gebrauchsanweisung

ECR International

ECR International 95M-200 Bedienungsanleitung

ECR International

ECR International Dunkirk PLYMOUTH STEAM 2 Series Gebrauchsanweisung

ECR International

ECR International Dunkirk DXL-060K Gebrauchsanweisung

ECR International

ECR International UTICA BOILERS SSV-050 Gebrauchsanweisung

ECR International

ECR International Dunkirk HELIX VX Gebrauchsanweisung

ECR International

ECR International PENNCO FSB 3 Series Gebrauchsanweisung

ECR International

ECR International Green Mountain GMGW Series Bedienungsanleitung

ECR International

ECR International Dunkirk DCB-75 Gebrauchsanweisung

ECR International

ECR International Green Mountain GMPVB 3 Series Gebrauchsanweisung

ECR International

ECR International Dunkirk Helix DKVLT-050 Gebrauchsanweisung

ECR International

ECR International GreenMountain GMGW Gebrauchsanweisung

ECR International

ECR International Green Mountain GM90-50 Bedienungsanleitung

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung

Radiant

Radiant R2K 55 Handbuch