ECRM Mako 4 CTP Handbuch

Mako 4 CTP

Operator Guide

Mako 4 CTP Operator Guide

This guide reﬂects the Mako CTP system as of October 2004.

Additional copies of this guide may be obtained by writing or calling:

ECRM Order Processing

554 Clark Road

Tewksbury, MA 01876

Phone No. (US) - (+1) 978-851-0207 — Fax (US) - (+1) 978-851-7016

Phone No. (UK) - (+44) 1923-218255 — Fax (UK) (+44) 1923-218256

Phone No. (Hong Kong) - (+852) 2-564-8989

Fax (Hong Kong) (+852) 2-564-8821

Visit our Web site: www.ecrm.com

Proprietary Notice

The information contained in this publication is the sole property of

ECRM. It cannot be reproduced, in whole or in part, without the express

written consent of ECRM. The information is believed to be accurate as of

the publication date, but it is subject to change without notice due to

continuing product development.

ECRM® and Mako® are trademarks of ECRM Imaging Systems. Other

brand and product names are trademarks or registered trademarks of their

respective owners.

AG45134 Rev. 3 iii

Table of Contents

Chapter Page Number

Chapter 1: Requirements and Safety.........................................................1-1

Introduction to the System ................................................................1-1

System Requirements .......................................................................1-1

Laser Safety ......................................................................................1-2

Regulatory Information .....................................................................1-3

Chapter 2: System Operation.....................................................................2-1

Introduction .......................................................................................2-1

Main Parts of the Platesetter ............................................................2-2

Starting Up the System .....................................................................2-5

Shutting Down the System ...............................................................2-5

Using the Control Panel ....................................................................2-6

Operator Menus ................................................................................2-8

Menu Selection ................................................................................2-8

User Preferences Menu .....................................................................2-9

User Maintenance Menu ...................................................................2-12

Test Patterns Menu ...........................................................................2-14

Running a Step Wedge Test Pattern .................................................2-19

Status Messages ................................................................................2-21

Error Messages .................................................................................2-22

System Configuration Display ..........................................................2-23

Chapter 3: Media Handling........................................................................3-1

Introduction .......................................................................................3-1

Installing and Removing the Pin Bar ................................................3-3

Loading Media ..................................................................................3-7

Chapter 4: Maintenance and Troubleshooting.........................................4-1

Introduction .......................................................................................4-1

General Maintenance ........................................................................4-1

Clearing Misfeeds .............................................................................4-6

Moving the System ...........................................................................4-9

iv AG45134 Rev. 3

AG45134 Rev. 3 v

Preface

Scope of this Guide

This guide provides instructions for the operating and maintaining a

Mako 4 CTP platesetter. This guide describes all aspects of the

operation of the system, from the loading of media, to the delivery

of exposed media to an on-line processor.

The Mako 4 CTP employs a Class 3B laser. This guide contains

important safety information and regulatory information about the

laser.You should read this information thoroughly before operating

the system or performing the procedures described in this guide.

This guide assumes that the system is already properly installed and

plugged into the AC mains. Further, this manual assumes that the

system has been calibrated and tested for proper operation and

acceptable output. Only procedures necessary for safe and efﬁcient

operation are provided in this manual.

Organization of this Guide

Chapter 1: Requirements and Safety

Chapter 1 includes system operating requirements and information

about laser safety.

Chapter 2: System Operation

Chapter 2 discusses all operational features and provides complete

listings of system operational messages. All of the system menus

are described in detail. All of the menu items are mapped in ﬂow

diagrams.

vi AG45134 Rev. 3

Chapter 3: Media Handling

Chapter 3 provides instructional information on how to load media.

Guidelines for handling media are also provided.

Chapter 4: General Maintenance andTroubleshooting

Chapter 5 covers general maintenance items that can be performed

by the operator. This chapter includes troubleshooting tips and a

procedure for re-locating or moving the system.

Not Covered in this Guide

Engineering Speciﬁcations

Alignment and Calibration

Detailed Field Service Information

Terms and Conventions Used in this Guide

Type This term is an instruction to type data at the

keyboard.

Italic

typeface Used to indicate the ﬁrst mention of an

important concept.

Bold

typeface Used to highlight important details in text or

illustrations and to indicate user actions.

Bold sans-serif

typeface Used to represent ﬁle names or menu options

to be selected. Also refers to section names.

Note

: Blocks of text used to advise of related

information.

IMPORTANT

Notices used to emphasize very important

information.

AG45134 Rev. 3 1

Requirements

and Safety

Introduction to the System

The Mako 4 CTP images printing plates. Plates are manually

loaded by positioning the plate in the pin registration system and

closing the pinch rollers. Imaging of the plate starts with the push of

a button. When the imaging is complete, the exposed plate

automatically moves onto the media transport, which feeds the

plate into a customer-supplied plate processor.

All operations must be performed in a safe-light environment.

System Requirements

System Power and Heat Dissipation

Power (maximum)

90 - 264 Volts; 3 Amps; 250 Watt

50/60Hz, single phase.

Heat Dissipation

850 BTU/hour

Environmental Requirements

Temperature

- 70 - 77 degrees F (21 - 25 degrees C)

Humidity

45 - 65%, non-condensing.

Note: Operating the system outside o the ranges speci ied

above may a ect per ormance.

1 - 2 AG45134 Rev. 3

Laser Sa ety

Laser Product Classiﬁcation

The system is classiﬁed as a Class one (I) laser product which

contains a Class 3B (IIIb) laser System. This classiﬁcation means

that the operator is exposed to no hazardous laser light during

operation and maintenance. The laser itself, however, is a Class 3B

(IIIb) laser device, and emits visible laser light which is considered

hazardous by FDA published limits.

IMPORTANTWARNING

Use o controls or adjustments or per ormance o

procedures other than those speci ied in this guide may

result in hazardous laser light exposure.

System LaserWavelength Identiﬁcation Label

The system contains a laser that emits visible laser light. The

identiﬁcation label is located on the output side of the machine,

above the output rollers. The label is shown in Figure 1-1.

Figure 1-1 Media Sensitivity Label

MEDIA SENSITIVITY

405 nm VISIBLE

AG45134 Rev. 3 1

Regulatory In ormation

Electromagnetic Emissions

DOC - Canada

The Canadian Department of Communications requires compliance

with the Radio Interference Regulations, ICES -003.

This digital apparatus does not exceed the ClassA limits for radio

noise emissions from digital apparatus set out in the Radio

Interference Regulations of the Canadian Department of

Communications.

EMC Directive - Europe

Complies with EN 55011: 1998

This is a Class A product. In a domestic environment this product

may cause radio interference in which case the user may be

required to take adequate measures.

FCC - USA

The standards for electromagnetic emissions are Part 15, Subpart J

of the FCC rules. The system was tested to Class A limits. The

following statements are required by the FCC:

Changes or modiﬁcations to this unit not expressly approved by the

party responsible for compliance could void your authority to

operate the equipment.

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in

accordance with the instruction guide, may cause harmful

interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which

1 - 4 AG45134 Rev. 3

case the user will be required to correct the interference at his or her

own expense.

Compliance with applicable regulations depends on the use of

shielded cables. It is the user who is responsible for procuring the

appropriate cables.

Identiﬁcation and Certiﬁcation Label (ratings plate)

The identiﬁcation and certiﬁcation label is attached to the back,

exterior of the unit, above the pinch rollers.

Figure 1-1 Identiﬁcation and Certiﬁcation Label

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received including

This class A digital apparatus complies with Canadian ICES-003.

Cet appareil numerique de la classe A est conforme a la norme NMB-003 du Canada.

This product conforms to all applicable provisions of Federal Regulations 21CF

1040.10 as required by 21CFR 1010.2 in effect as of the date of manufacture.

AT TEWKSBURY, MA. U.S.A.

ECRM Incorporated, 554 CLARK ROAD, TEWKSBURY, MA. 01876

MANUFACTURED

Model No.

Serial No.

CLASS 1 LASER PRODUCT

APPAREIL A LASER DE CLASSE 1

LASER KLASSE 1

interference that may cause undesired operations.

LR67907

CUS

Andere Handbücher für Mako 4 CTP

Inhaltsverzeichnis

Andere ECRM Multifunktionsdrucker Handbücher

ECRM

ECRM Mako 4 CTP Handbuch

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung