ECS P4S5A Bedienungsanleitung

Preface

This publication, including all photographs, illustrations and software, is protected un-

of the material contained herein, may be reproduced without writtenconsent ofthe au-

thor.

Version 5.1a

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any par-

ticular purpose. The manufacturer reserves the right to revise this publication and to

make changes from time to time in the content hereof without obligation of the manu-

facturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digi-

tal device, pursuant to Part 15 of the FCC Rules. These limitsare designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not oc-

cur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

−Reorient or relocate the receiving antenna.

−Increase the separation between the equipment and the receiver.

−Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected.

−Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system's manu-

facturer could void the user's authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

−This device may not cause harmful interference, and

−This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Mainboard Describes features of the mainboard,

and provides a shipping checklist.

Go to ⇒page 1

Chapter 2

Installing the Mainboard Describes installation of mainboard

components.

Go to ⇒page 6

Chapter 3

Using BIOS Provides information on using the BIOS

Setup Utility.

Go to ⇒page 24

Chapter 4

Using the Mainboard Software Describes the mainboard software.

Go to ⇒page 36

iii

Preface i

Features and Packing List Translations 錯誤! 尚未定義書籤。

CHAPTER 1 1

Introducing the Mainboard 1

Introduction............................................................................................................1

Checklist.................................................................................................................1

Standard Items ...................................................................................................1

Features..................................................................................................................2

Choosing a Computer Case................................................................................4

Mainboard Components.......................................................................................5

CHAPTER 2 6

Installing the Mainboard 6

Safety Precautions................................................................................................6

Quick Guide...........................................................................................................6

Installing the Mainboard in a Case.....................................................................7

Checking Jumper Settings...................................................................................7

Setting Jumpers .................................................................................................7

Checking Jumper Settings.................................................................................8

Jumper Settings.................................................................................................8

Connecting Case Components...........................................................................9

The FPI Connector............................................................................................9

Installing Hardware.............................................................................................10

Installing the Processor...................................................................................10

InstallingMemoryModules............................................................................13

Installing a Hard Disk Drive/CD-ROM ..........................................................14

Installing a Floppy Diskette Drive ..................................................................16

InstallingAdd-on Cards..................................................................................17

Connecting Optional Devices..........................................................................19

ConnectingI/ODevices.....................................................................................22

CHAPTER 3 24

Using BIOS 24

About the Setup Utility........................................................................................24

The Standard Configuration............................................................................24

Running the Setup Utility................................................................................25

Using BIOS..........................................................................................................25

Standard CMOS Features................................................................................26

Advanced BIOS Setup Option........................................................................27

Power Management Setup Page......................................................................29

PCI / Plug and Play Setup...............................................................................30

Load Optimal Settings.....................................................................................31

Load Best Performance Settings.....................................................................31

Features Setup Page.........................................................................................31

CPU PnP Setup Page.......................................................................................33

HardwareMonitorPage..................................................................................34

ChangePassword ............................................................................................35

Change or Remove the Password....................................................................35

Exit ..................................................................................................................35

CHAPTER 4 36

Using the Mainboard Software 36

About the Software CD-ROM............................................................................36

Auto-installing under Windows 98....................................................................36

Running Setup.................................................................................................37

Manual Installation..............................................................................................39

Utility Software Reference.................................................................................39

Award Flash Memory Utility...........................................................................39

PC-CILLIN......................................................................................................39

MediaRing Talk – Telephony Software...........................................................40

Super Voice –Fax/Modem Software...............................................................40

WinFlash Utility..............................................................................................40

CD Ghost.........................................................................................................40

Recovery Genius.............................................................................................40

Language Genius.............................................................................................40

PageABC.........................................................................................................40

Introducing the Mainboard

Congratulations on purchasing the P4S5A mainboard. This mainboard has a

Socket-478 processor socket for Intel Pentium 4 type of processorssupport-

ing front side bus (FSB) speeds up to400/533 MHz.

This mainboard integrates the SiS 645/SiS 645DX Northbridge along with

961A/961B/962 Southbridge chipsets that supports built-in AC97 Codec sup-

port 4-channel speak-out, 2DDR + 2 SDR modules up to 2GB system

memory. These chipsets’ function is detailed as the Chipset description in next

section. This mainboard has one4X AGP slot for highly graphics display, one

AMR (Audio Modem Riser) slot to support Audio and Modem application, and

built-in 10BaseT/100BaseTX Network Interface. There is a full set of I/O

ports including two PS/2 ports for mouse and keyboard, two serial ports, one

parallel port, one MIDI/game port and four USB ports -- two backpanel ports

and onboard USB header USB1 providing two extra ports (they will support

USB 2.0 if SiS 962 SB installed on the mainboard). By means of the Extended

USB Module connected to the mainboard, you can make two extra USB ports.

This mainboard is an ATX mainboard that uses a 4-layer printed circuit board

and measures 305 x 244mm.

Compare the mainboard’s package contents with the following checklist:

Standard Items

•One mainboard

•One diskette drive ribbon cable

•One IDE drive ribbon cable

•Software support CD

•One Retention Module

•The User’s Manual

Processor •The PGA Socket 478

•Supports Intel Pentium 4 series CPUs

•Supports up to 400/533 MHz Frontside Bus

Note: SiS 645DX Northbridge supports up to 533MHz

Frontside bus.

The SiS 645/SiS 645DX and SiS961 chipsets are based on an

innovative and scalable architecture with proven reliability and

performance. A few of the chipset’s advanced features are:

•A low 2.5-volt DDR SDRAM power consumption which

makes it an excellent solution for notebooks and desktops

with a small footprint

•Support for a 4xAGP interface providing vivid 3D graphics

and video performance

•An ATA 100 interface on the chipset, which helps boost

system performance by providing a high-speed connec-

tion to ATA 100 Hard Disk Drives, delivering maximum

sustained data transfer rates of 100 MB/sec

•Built-in multithreaded I/O link used to enhance perform-

ance, providing enough I/O bandwidth for throughput up

to 1.2 GB/s

Additional key features include support for six USB ports, an

AC 97 link for audio and modem, hardware monitoring, and

ACPI/OnNow power management.

Chipset

This mainboard may support either one of the three

Southbridge chipset. Refer below for details:

•SiS961A Southbridge –supports up to 400/533MHz and

Ultra DMA ATA 100 interface.

•SiS961B Southbridge –supports up to 400/533MHz and

Ultra DMA ATA 133 interface.

•SiS962 Southbridge –supports up to 533MHz, Ultra

DMA ATA133 interface and IEEE 1394 controller.

Memory •Two 168-pin DIMM slots for SDRAM memory modules

•Two 184-pin DIMM slots for DDR memory modules

•Support SDRAM up to 133 MHz /DDR up to 333 MHz

memory bus

•Maximum installed memory is 2GB

Note: You cannot use SDRAM and DDR simultane-

ously.

Expansion Slots •One AMR slot for a special audio/modem riser card

•One 4xAGP slot for AGP 2.0-compliant interface

•Five 32-bit PCI slots for PCI 2.2-compliant bus interface

Onboard IDE

channels •Primary and Secondary PCI IDE channels

•Support for PIO (programmable input/output) modes

•Support for Multiword DMA modes

•Support for Bus Mastering and Ultra DMA ATA 100/133

modes

Power

Supply and

Power

•ATX power supply connector

•Meets ACPI 1.0b and APM 1.2 requirements, keyboard

power on/off

Power

Management •Supports RTC Alarm, Wake On Modem, AC97 Wake-Up

and USB Wake-Up

VGA This mainboard includes a 4xAGP slot that provides four times

the bandwidth of the original AGP specification. AGP technol-

ogy provides a direct connection between the graphics sub-

system and memory so that the graphics do not have to com-

pete for processor time with other devices on the PCI bus.

USB (optional) The USB 2.0 Controller is compliant with Universal Serial Bus

Specification Revision 2.0.

The USB 2.0 supports data transfer rates up to 480MB/sec for

high-speed devices and specifies a microframe that will be

1/8th of a 1msec frame. This allows the USB 2.0 devices to

have small buffers even at high data rates.

The USB 1.1 connectors and other full speed cables can sup-

port the higher speed of USB 2.0 without any changes.

The chipset has the following advanced USB features:

•Compliant with Enhanced Host Controller Interface

(EHCI) Specification Revision 0.95 and Universal Host

Controller Interface (UHCI) Specification Revision 1.1

•PCI multi-function device consists of two UHCI Host Control-

lers for full/low-speed signaling and one EHCI Host

Controller core for high-speed signaling

•Supports PCI-Bus Power Management Interface Specifi-

cation release 1.1

•Legacy support for all downstream facing ports

IEEE 1394 Con-

troller Interface

(optional)

•Fully supports provisions of IEEE 1394-1995 and P1394A

for high performance serial bus

•Provides two fully compliant cable ports at 100/200/400

Mbits and operates in one, two or three port mode

•Single 24.576 MHZ crystal provide transmit/receive data

at 100/200/400 Mbits/s and LLC clock at 49.152 M

•Separate cable bias (TPBIAS) and driver termination

voltage supply for each port

•Support power-down feature to conserve energy in bat-

tery powered applications

AC’97 Audio

Codec •Compliant with AC’97 2.2 specification

•Full-duplex Codec with independent and variable sam-

pling rate

•Earphone Buffer Built-In, SNR up to 90db

•4Ch DAC, support 4-channel speak-out

•Advanced power management support

Built-in Ethernet

LAN (optional) •Built-in 10BaseT/100BaseTX Ethernet LAN

•SiS961 Embedded Fast Ethernet MAC and onboard

Realtek RTL8201 LAN PHY compliant with IEEE802.3u

100BASE-TX, 10BASE-T and ANSI X3.263 TP-PMD

standards

•Compliant with ACPI 1.0 and the Network Device Class

Power Management 1.0

•High Performance provided by 100Mbps clock generator

and data recovery circuit for 100Mbps receiver

Onboard I/O

Ports The mainboard has a full set of I/O ports and connectors:

•Two PS/2 ports for mouse and keyboard

•Two serial ports

•One parallel port

•One MIDI/game port

•Four USB ports (two backpanel ports, onboard USB

headers providing two extra ports)

•Audio jacks for microphone, line-in and line-out

Hardware Moni-

toring Built-in hardware monitoring for CPU & System temperatures,

fan speeds and mainboard voltages.

Onboard Flash

ROM Supports Plug and Play configuration of peripheral devices

and expansion cards

Dimensions ATX form factor 305 x 244 mm

There are many types of computer cases on the market. The mainboard com-

plies with the specifications for the ATX system case. Some features on the

mainboard are implemented by cabling connectors on the mainboard to indi-

cators and switches on the system case. Ensure that your case supports all

the features required. The mainboard can support one floppy diskette drive

and four enhanced IDE drives. Ensure that your case has sufficient power and

space for all the drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that

the I/O template in the case matches the I/O ports installed on the rear edge

of the mainboard.

This mainboard has an ATX form factor of305 x 244 mm. Choose a case that

accommodates this form factor.

This concludes Chapter 1. The next chapter explains how to install the main-

board.

Installing the Mainboard

Follow these safety precautions when installing the mainboard:

•Wear a grounding strap attached to a grounded device to avoid

damage from static electricity.

•Discharge static electricity by touching the metal case of a safely

grounded object before working on the mainboard.

•Leave components in the static-proof bags they came in.

•Hold all circuit boards by the edges. Do not bend circuit boards.

This Quick Guide suggests the steps you can take to assemble your system

with the mainboards.

The following table provides a reference for installing specific components:

Locating Mainboard Components Go to page 5

Installing the Mainboard in a Case Go to page 7

Setting Jumpers Go to page 7

Installing Case Components Go to page 9

Installing the CPU Go to page 10

Installing Memory Go to page 13

Installing an HDD and CD-ROM Drive Go to page 14

Installing an FDD Go to page 16

Installing Add-on Cards Go to page 17

Connecting Options Go to page 19

Connecting Peripheral (I/O) Devices Go to page 22

Inhaltsverzeichnis

Andere ECS Hauptplatine Handbücher

ECS

ECS P6LX2-A Bedienungsanleitung

ECS

ECS 945PT-A2/1333 Bedienungsanleitung

ECS

ECS P6VPA2T Bedienungsanleitung

ECS

ECS Motherboard Bedienungsanleitung

ECS

ECS Motherboard Bedienungsanleitung

ECS

ECS L4IBMGL Bedienungsanleitung

ECS

ECS P4M890T-M2 Bedienungsanleitung

ECS

ECS H61H2-M17 Bedienungsanleitung

ECS

ECS G41T-M5 Bedienungsanleitung

ECS

ECS 760GX-M Bedienungsanleitung

ECS

ECS 662/1066T-M2 Bedienungsanleitung

ECS

ECS IC780M-A2 Bedienungsanleitung

ECS

ECS Z170IU-C43 Bedienungsanleitung

ECS

ECS 915GV-M10 Bedienungsanleitung

ECS

ECS 945GCT-M3 Bedienungsanleitung

ECS

ECS H97I-DRONE Bedienungsanleitung

ECS

ECS Mainboard Bedienungsanleitung

ECS

ECS L7VTA3 Bedienungsanleitung

ECS

ECS G45T-M2 Bedienungsanleitung

ECS

ECS L4IBME 1.0 Bedienungsanleitung

ECS

ECS NFORCE6M-A Bedienungsanleitung

ECS

ECS H55H-CM Bedienungsanleitung

ECS

ECS GeForce 7050M-M Bedienungsanleitung

ECS

ECS K7VZA Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung