ECS P4VMM2 Bedienungsanleitung

Preface

This publication, including all photographs, illustrations and software, is protected un-

of the material contained herein, may be reproduced without written consent of the au-

thor.

Version 7.3

Disclaimer

The information in this document is subject to change without notice. The manufac-

turer makes no representations or warranties with respect to the contents hereof and

specifically disclaims any implied warranties of merchantability or fitness for any par-

ticular purpose. The manufacturer reserves the right to revise this publication and to

make changes from time to time in the content hereof without obligation of the manu-

facturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel

Corporation.

Other product names used in this manual are the properties of their respective owners

and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digi-

tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not oc-

cur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

− Reorient or relocate the receiving antenna.

− Increase the separation between the equipment and the receiver.

− Connect the equipment onto an outlet on a circuit different from that to which

the receiver is connected.

− Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits governing

this device. Changes or modifications not expressly approved by the system's manu-

facturer could void the user's authority to operate the equipment.

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

− This device may not cause harmful interference, and

− This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-

causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement

sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Mainboard

Describes features of the mainboard,

and provides a shipping checklist.

Go to ⇒page 1

Chapter 2

Installing the Mainboard

Describes installation of mainboard

components.

Go to ⇒page 7

Chapter 3

Using BIOS

Provides information on using the BIOS

Setup Utility.

Go to ⇒page 21

Chapter 4

Using the Mainboard Software

Describes the mainboard software.

Go to ⇒page 32

Preface i

CHAPTER 1 1

Introducing the Mainboard 1

Introduction.................................................................................................1

Checklist.....................................................................................................1

Standard Items................................................................................................. 1

Features .....................................................................................................1

Choosing a Computer Case .......................................................................4

Mainboard Components .............................................................................5

CHAPTER 2 7

Installing the Mainboard 7

Mainboard Installation.................................................................................7

Installing the Processor ..............................................................................8

Installing Memory Modules.........................................................................9

Checking Jumper Settings........................................................................11

Connecting Case Components.................................................................13

The Panel Connectors.................................................................................... 14

Floppy Diskette Drive Installation................................................................. 15

IDE Devices .................................................................................................. 15

Installing Add-on Cards................................................................................. 16

Connecting Optional Devices........................................................................ 17

Connecting I/O Devices............................................................................19

External Connector Color Coding ................................................................. 20

CHAPTER 3 21

Using BIOS 21

About the Setup Utility..............................................................................21

The Standard Configuration .......................................................................... 21

Entering the Setup Utility.............................................................................. 22

Using BIOS...............................................................................................22

Standard CMOS Features.............................................................................. 23

Advanced Setup Page.................................................................................... 24

Power Management Setup Page .................................................................... 26

PCI / Plug and Play Setup Page..................................................................... 27

Load Optimal Settings................................................................................... 28

Load Best Performance Settings.................................................................... 28

Features Setup Page....................................................................................... 28

CPU PnP Setup Page..................................................................................... 30

Hardware Monitor Page................................................................................. 30

iii

CHAPTER 4 31

Using the Mainboard Software 32

About the Software CD-ROM ...................................................................32

Auto-installing under Windows 98/ME/2000/XP .......................................32

Running Setup............................................................................................... 33

Manual Installation....................................................................................35

Utility Software Reference ........................................................................35

Introducing the Mainboard

Thank you for choosing the P4VMM2 mainboard. This mainboard has a

Socket 478 for the Intel Pentium 4 type of processors supporting front side

bus (FSB) speeds up to 533/400 MHz.

This mainboard incorporates the VIA P4M266/A Northbridge and VT8235

Southbridge chipsets that support AC 97 audio codec, and provide Ultra DMA

133/100/66/33 function. It supports built-in USB 2.0 providing higher band-

width. It implements Universal Serial Bus Specification Revision 2.0 and is

compliant with UHCI 1.1 and EHCI 0.95. This mainboard has two 32-bit PCI

slots, one 4xAGP slot, one CNR (Communications and Networking Riser) slot,

and an onboard 10BaseT/100BaseTX Network interface (optional). In addition,

this mainboard has a full set of I/O ports including two PS/2 ports for mouse

and keyboard, one serial port, one VGA port, one parallel port and six USB2.0

ports– four back-panel ports and onboard USB header USB2 providing two

extra ports by connecting the Extended USB Module to the mainboard.

This mainboard is a Micro ATX size mainboard and has power connectors for

an ATX power supply.

Compare the mainboard’s package contents with the following checklist:

Standard Items

• One mainboard

• One diskette drive ribbon cable

• One IDE drive ribbon cable

• Retention Module

• Software support CD

• This user’s manual

Processor The P4VMM2 mainboard uses a mPGA478 Socket that has

the following features:

• Accommodates Intel Pentium 4 478-pins CPU

• Supports a front-side bus (FSB) of 400/533 MHz

Chipset The P4M266/A Northbridge and VT8235 Southbridge in this

chipset in accordance with an innovative and scalable archi-

tecture with proven reliability and performance. A few of the

chipset’s advanced features are:

• An advanced V-Link memory controller architecture that

provides the bandwidth up to 533 MB/s and performance

necessary for even the most demanding Internet and 3D

graphics

• Support for an 4xAGP interface providing vivid 3D graph-

ics and video performance

• An ATA 133 interface on the chipset, which helps boost

system performance by providing a high-speed connec-

tion to ATA 133 Hard Disk Drives, delivering maximum

sustained data transfer rates of 133 MB/sec

Additional key features include support for six USB ports, an

AC 97 link for audio and modem, hardware monitoring, and

ACPI/OnNow power management.

Memory • The mainboard accommodates two 184-pin, 2.5V DDR

DIMM sockets with a total capacity of 2 GB system mem-

ory

• Supports DDR up to 200/266MHz memory bus

Built-in Graphics

System

• P4M266/A integrates S3’s Savag4graphics accelera-

tor into a single chip. P4M266/A brings mainstream

graphics performance to the Value PC with leading-edge

2D, 3D and DVD video acceleration into a cost effective

package. Based on its capabilities, P4M266/A is an ideal

solution for the consumer, corporate mobile users and en-

try-level professionals

• Maximum-shared memory size is 32 MB

Graphics This mainboard includes an AGP slot that provides four times

the bandwidth of the original AGP specification. AGP technol-

ogy provides a direct connection between the graphics sub-

system and memory so that the graphics do not have to com-

pete for processor time with other devices on the PCI bus.

AC’97 Audio

Codec

• Compliant with AC’97 2.1 specification

• 16-bit stereo full-duplex CODEC with fixed 48KHz sam-

pling rate

• 3 analog line-level stereo inputs with 5-bit volume control:

LINE-IN, CD-IN, AUX-IN

• 1 analog line-level mono input: PHONE-IN

• Three Audio Jacks – Line-Out, Line-In and Microphone-In

• Sound Blaster, Sound Blaster Pro Compatible

• Digital I/O compatible with consumer mode S/PDIF

• Advanced power management support

Expansion

Options The mainboard comes with the following expansion options:

• Two 32-bit PCI slots ca

able of Ultra DMA bus maste

with transfer rates of 33/66/100/133 MB/sec

• An AGP slot

• One CNR (Communications and Networking Riser) slot

Integrated I/O The mainboard has a full set of I/O ports and connectors:

• Two PS/2 ports for mouse and keyboard

• One serial port

• One VGA port

• One parallel port

• Six USB2.0 ports (four back-panel ports, onboard USB

header providing two extra ports)

• Audio jacks for microphone, line-in and line-out

USB 2.0 • Compliant with Universal Serial Bus Specification Revi-

sion 2.0

• Compliant with Intel’s Enhanced Host Controller

Interface Specification Revision 0.95

• Compliant with Universal Host Controller Interface

Specification Revision 1.1

• PCI multi-function device consists of two UHCI Host

Controller cores for full-/low-speed signaling and one

EHCI Host Controller core for high-speed signaling

• Root hub consists 4 downstream facing ports with

integrated physical layer transceivers shared by UHCI

and EHCI Host Controller

• Support PCI-Bus Power Management Interface

Specification release 1.1

• Legacy support for all downstream facing ports

Built-in Ethernet

LAN (optional)

• 100Base-TX/10Base-T Physical Layer Solution

• Dual Speed – 100/10 Mbps

• MII Interface to Ethernet Controller/Configuration & Status

• Auto Negotiation: 10/100, Full/Half Duplex

• Meet All Applicable IEEE802.3, 10Base-T and 100Base-

TX Standards

BIOS Firmware This mainboard uses AMI BIOS that enables users to config-

ure many system features including the following:

• Power management

• Wake-up alarms

• CPU parameters and memory timing

• CPU and memory timing

The firmware can also be used to set parameters for different

processor clock speeds.

Some hardware specifications and software items are subject to change

without prior notice.

There are many types of computer cases on the market. The mainboard com-

plies with the specifications for the Micro-ATX system case. Some features on

the mainboard are implemented by cabling connectors on the mainboard to

indicators and switches on the system case. Ensure that your case supports

all the features required. The mainboard can support one or two floppy disk-

ette drives and four enhanced IDE drives. Ensure that your case has sufficient

power and space for all the drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that

the I/O template in the case matches the I/O ports installed on the rear edge

of the mainboard.

This mainboard has a Micro-ATX form factor of 244 mm x 200 mm. Choose a

case that accommodates this form factor.

Table of Mainboard Components

Label Component

AGP1 Accelerated Graphics Port

BAT1 Three volt realtime clock battery

CD1 Primary CD-in connector

CD2 Secondary CD-in connector

CN5 Standard power connector

CNR1 Communications Networking Riser slot

CPU SOCKET Micro PGA 478-pin socket for Pentium 4 CPUs

CPU_FAN Cooling fan for CPU

DDR1 ~ DDR2 Two 184-pin DDR memory modules

FDC Floppy disk drive connector

IDE 1 Primary IDE channel

IDE 2 Secondary IDE channel

J1 USB Card Reader Voltage Selector (VCC)

J16 Onboard LAN LED connector

JBAT1 Clear CMOS jumper

JP1A1/JP1B1 CPU Clock jumper

JP2 Keyboard Power On jumper

JUSBC USB Card Reader Connector

PANEL1 Connector for headphone or microphone jack front panel

PANEL2 Connector for case front panel switches and LED indicators

PCI1 ~ PCI2 Two 32-bit add-on card slots

PJ1 Auxiliary power connector for Pentium 4 CPUs

SIR1 Serial Infrared cable header

SPK1 Internal speaker connector

SYSTEM_FAN System fan connector

USB2 Front Panel USB headers

This concludes Chapter 1. The next chapter explains how to install the main-

board.

Andere Handbücher für P4VMM2

Inhaltsverzeichnis

Andere ECS Hauptplatine Handbücher

ECS

ECS H77H2-M Bedienungsanleitung

ECS

ECS H67H2-M Bedienungsanleitung

ECS

ECS A780GM-A Ultra Bedienungsanleitung

ECS

ECS A770M-A Bedienungsanleitung

ECS

ECS Photon Extreme KN3 SLI2 Bedienungsanleitung

ECS

ECS 845PE-A800 Bedienungsanleitung

ECS

ECS BAT-I3 Bedienungsanleitung

ECS

ECS Elitegroup P4M8OOPRO Bedienungsanleitung

ECS

ECS G45T-M2 Bedienungsanleitung

ECS

ECS H61H2-M6 Bedienungsanleitung

ECS

ECS G41T-R3 Bedienungsanleitung

ECS

ECS A880GM-M6 Bedienungsanleitung

ECS

ECS H55H-M2 Bedienungsanleitung

ECS

ECS P45T-A Bedienungsanleitung

ECS

ECS NM70-M Bedienungsanleitung

ECS

ECS H61H2-M9 Bedienungsanleitung

ECS

ECS RS400-A Bedienungsanleitung

ECS

ECS A785GM-M Bedienungsanleitung

ECS

ECS P67H2-A2 Bedienungsanleitung

ECS

ECS IC890GXM-A Bedienungsanleitung

ECS

ECS 965PLT-A Bedienungsanleitung

ECS

ECS H61H2-M8 Bedienungsanleitung

ECS

ECS P6VAP-Me Bedienungsanleitung

ECS

ECS B75H2-M3 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung