Eddylight EDD-GL-183 Bedienungsanleitung
Flat LED Par Can Light
EDD-GL-183
USER MANUAL
1. Introduction
Thank you for purchasing our Million Color Flat LED light. Please read
these instructions carefully before operating to avoid any possible damage
and accidents caused by misuse.
The Million Color Flat LED light has a solid steel body. Three colors of
high-brightness LED lights (red, blue, green) are used to create a wide
spectrum of colors. It draws low power, has a low profile, dual mounting
yokes in the handle and is low weight. The DMX controls include dimming,
strobe, sound activation and independent control of RGB. The unit is
compatible with the standard DMX 512 signal for external DMX control.
Practical uses of the product include dance halls, stage backgrounds,
hotels, large-scale performances, drapery uplighting and stage lighting.
Packing List
- Million color flat LED light
- Power cable
- User manual
- Warranty card
2. Safety Information
- Please consult skilled service technicians for any repairs required
- Always disconnect from the power source before setting up, moving and
servicing
- Avoid direct eye contact to the light when in operation
- Make sure the power supply voltage is compatible with this light
- Before installation, please check the light’s fasteners and mechanical
structure is in good condition and not damaged
- The light is designed for indoor use, below 40 degrees celsius
- The fixture may be mounted in any position provided there is adequate
room for ventilation. Make sure there are no flammable and explosive
items within 0.5 meters.
- Please ensure the ground is always connected
4. DMX Channel Assignment
5 Channel Mode
Channel
DMX
Value
Function
Notes
1
0-255
Red dimming
0—100%
Invalid while CH8 is
51-255
2
0-255
Green dimming
0—100%
Invalid while CH8 is
51-255
3
0-255
Blue dimming
0—100%
Invalid while CH8 is
51-255
4
0-255
Amber dimming
0—100%
Invalid while CH8 is
51-255
5
N/A
N/A
9 Channel Mode
Channel
DMX
Value
Function
Notes
1
0-255
Red dimming
0—100%
Invalid while CH8 is
51-255
2
0-255
Green dimming
0—100%
Invalid while CH8 is
51-255
3
0-255
Blue dimming
0—100%
Invalid while CH8 is
51-255
4
0-255
Amber dimming
0—100%
Invalid while CH8 is
51-255
5
N/A
N/A
6
0-255
RGBA dimming
0—100%
Invalid while CH8 is
51-255
7
0-255
Strobe light
Fader controls speed
8
10-255
Color Changing
Fader controls speed
9
128-255
Color fading/
sound activated
Overrides other modes
5. Rear Panel Display and Operation
MENU: Access the menu or return to a previous menu option
UP: Menu selection or parameter increments
DOWN: Menu selection or parameter increments
ENTER: Select the current menu option
6. Instructions for Manual Programming
MENU items:
•!”Addr”: DMX mode (001-512)
•“Slav”: Slave mode
•!“Chnd”: DMX channel mode (5CH/9CH)
•!“SouA”: Sound activated mode
•!”SP”: Built-in program speed change mode (speed = 0-15)
•“Pr”: Built-in preset programs (0-11)
•!”Colo”: Preset colors (0-30)
•“Strb”: Strobe mode (speed = 0-15)
•!”r”: Solid color mode, red setting (0-255)
•!”g”: Solid color mode, green setting (0-255)
•!”b”: Solid color mode, blue setting (0-255)
•!”a”: Solid color mode, blue setting (0-255)
Press MENU to enter the main menu, and use UP/DOWN to cycle through
the different modes. Press ENTER to select the desired mode, and UP/
DOWN buttons to cycle through the different mode values (ie. 0-99, etc).
Press ENTER to select that value and save your selection.
For example, to Enter DMX mode, operate as follows:
5
www.EddylightCo.com 1-800-914-3538
LED Display
Menu Up Down Enter
Selection buttons
DMX OUT DMX IN
DMX input/output Power in/out
120V AC OUT 120V AC IN
•Press MENU repeatedly until “d001”
•Press UP / DOWN to select your desired address (ie. “d017”)
•Press ENTER to choose.
7. Color Selection Guide:
Set the RGBA values using MENU on the back of the unit, or by using the
DMX control board. Experiment with the different values to create different
colors (ie. adding more Green to Red will make the red more orangey).
Color
Name
Red
Green
Blue
Amber
!
Red
255
0
0
0
!
Green
0
255
0
0
!
Blue
0
0
255
0
!
Amber
0
0
0
255
!
White
255
255
255
255
!
Yellow
255
255
0
0
!
Magenta
255
0
255
0
!
Cyan
0
255
255
0
!
Champagne
0
0
0
255
!
Cold White
255
255
255
0
!
Warm White
255
255
255
255
8. Cable Connection
A standard XLR connection is used for the DMX 512 protocol:
Note: DMX512 does not include automatic error checking and correction,
and so is not an appropriate control for hazardous applications, such as
pyrotechnics or movement of theatrical rigging. False triggering may be
caused by electromagnetic interference, static electricity discharges,
improper cable termination, excessively long cables, or poor quality
cables.
Note: In order to avoid failures and
signal interference, it is recommended
to connect a 120Ωresistor (1/4W) at the
end of the DMX connection as shown on
right. If using 5-pin DMX, please use a
5-pin to 3-pin cable adapter. Details on
configuration below:
7
www.EddylightCo.com 1-800-914-3538
Inhaltsverzeichnis
Andere Eddylight Beleuchtungsausrüstung Handbücher
Eddylight
Eddylight DSY-LED252-IP65-RGB Bedienungsanleitung
Eddylight
Eddylight EDD-RP-WBIF1006 Bedienungsanleitung
Eddylight
Eddylight DS-1404A Bedienungsanleitung
Eddylight
Eddylight LED GOBO Bedienungsanleitung
Eddylight
Eddylight LED PAR 64 Bedienungsanleitung
Eddylight
Eddylight Economy Bedienungsanleitung
Eddylight
Eddylight EDD-VP-S120 Bedienungsanleitung
Eddylight
Eddylight 4 in 1 RGBW SlimPar LED Q18 Bedienungsanleitung
Eddylight
Eddylight DSY-LED252-IP65-RGB Bedienungsanleitung
Eddylight
Eddylight DSY-LED252-IP65-RGB Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
