Edge-Core ECS4660-28F Programmierhandbuch

Management Guide

www.edge-core.com

ECS4660-28F Layer 3

Gigabit Ethernet Switch

ANAGEMENT

UIDE

ECS4660-28F GIGABIT ETHERNET SWITCH

Layer 3 Switch

with 24 Gigabit Ethernet Ports (SFP),

2 10G Ethernet Ports (XSFP), and

2 Slots for Optional 10G Modules

ECS4660-28F

E102013/ST-R03

149100000140A

– 5 –

ABOUT THIS GUIDE

PURPOSE This guide gives specific information on how to operate and use the

management functions of the switch.

AUDIENCE The guide is intended for use by network administrators who are

responsible for operating and maintaining network equipment;

consequently, it assumes a basic working knowledge of general switch

functions, the Internet Protocol (IP), and Simple Network Management

Protocol (SNMP).

CONVENTIONS The following conventions are used throughout this guide to show

information:

OTE

Emphasizes important information or calls your attention to related

features or instructions.

AUTION

Alerts you to a potential hazard that could cause loss of data, or

damage the system or equipment.

ARNING

Alerts you to a potential hazard that could cause personal injury.

RELATED PUBLICATIONS The following publication details the hardware features of the switch,

including the physical and performance-related characteristics, and how to

install the switch:

The Installation Guide

Also, as part of the switch’s software, there is an online web-based help

that describes all management related features.

BOUT

HIS

UIDE

– 6 –

REVISION HISTORY This section summarizes the changes in each revision of this guide.

OCTOBER 2013 REVISION

This is the third release of this guide. This guide is valid for software

release V1.2.2.0. It includes information on the following changes:

◆Updated information in Parameters section under "Configuring the

Console Port" on page 172.

◆Updated information in Parameters section under "Configuring Telnet

Settings" on page 174.

◆Updated Command Usage and Parameters sections under "Configuring

by Port List" on page 182.

◆Updated descriptive text under "Configuring by Port Range" on

page 184.

◆Added "Configuring History Sampling" on page 196.

◆Temporarily removed “Sampling Traffic Flows.”

◆Updated Parameters section under "Enabling QinQ Tunneling on the

Switch" on page 247.

◆Added "Creating CVLAN to SPVLAN Mapping Entries" on page 248.

◆Added "Mapping Ingress DSCP Values to Internal DSCP Values" on

page 314.

◆Updated Command Usage and Parameters sections under "Attaching a

Policy Map to a Port" on page 339.

◆Updated Parameters section under "Binding a Port to an Access Control

List" on page 408.

◆Updated Parameters section under "Configuring Global Settings for ARP

Inspection" on page 411.

◆Added "DoS Protection" on page 431.

◆Added "IPv6 Source Guard" on page 438.

◆Updated Table 34, "Supported Notification Messages," on page 490.

◆Updated Parameters section under "Configuring IGMP Snooping and

Query Parameters" on page 613.

◆Updated Parameters section under "Configuring MVR Domain Settings"

on page 660.

◆Updated Parameters section under "Configuring MVR6 Domain

Settings" on page 677.

BOUT

HIS

UIDE

– 7 –

◆Updated Parameters section under "Using the Trace Route Function" on

page 746.

◆Added commands "show watchdog" on page 909 and "watchdog

software" on page 909.

◆Updated syntax for command "delete" on page 917.

◆Updated range for command "exec-timeout" on page 925.

◆Added the commands "clock summer-time (date)" on page 951, "clock

summer-time (predefined)" on page 953, and "clock summer-time

(recurring)" on page 954.

◆Updated displayed data for the command "show snmp" on page 999.

◆Updated syntax for "snmp-server enable traps" on page 1000.

◆Added the command "snmp-server enable port-traps mac-notification"

on page 1003 and "show snmp-server enable port-traps" on

page 1004.

◆Updated the command under "Flow Sampling Commands" on

page 1025.

◆Updated syntax for the command "ip source-guard binding" on

page 1134, "ip source-guard max-binding" on page 1137, and "show ip

source-guard binding" on page 1139.

◆Added the commands "ip source-guard mode" on page 1138 and "clear

ip source-guard binding blocked" on page 1138.

◆Updated syntax for the command "ip arp inspection validate" on

page 1149.

◆Updated syntax for the command "traffic-segmentation uplink/

downlink" on page 1159.

◆Updated syntax for the command "ip access-group" on page 1168,

"ipv6 access-group" on page 1174, and "mac access-group" on

page 1179.

◆Added the command "clear access-list hardware counters" on

page 1184.

◆Updated syntax for the command "show access-list" on page 1185.

◆Updated syntax and command usage sections for the command

"capabilities" on page 1189.

◆Added the command "discard" on page 1191 and "show discard" on

page 1197.

◆Updated information for the command "media-type" on page 1193.

BOUT

HIS

UIDE

– 8 –

◆Updated command usage section for the command "negotiation" on

page 1194.

◆Removed the command “speed-duplex.”

◆Moved the switchport packet-rate command from Interface Commands

chapter to Congestion Control Commands on page 1241.

◆Added the commands "transceiver-threshold-auto" on page 1205, and

"transceiver-threshold-monitor" on page 1206.

◆Updated description of all other transceiver threshold command from

page 1206 to page 1212.

◆Added "Loopback Detection Commands" on page 1259.

◆Added the command "spanning-tree tc-prop-stop" on page 1300.

◆Updated introductory text and command usage section for the

command "interface vlan" on page 1345.

◆Updated syntax for the command "show queue mode" on page 1391.

◆Updated syntax for the command "show qos map ip-port-dscp" on

page 1403.

◆Added the command "ip igmp snooping priority" on page 1428.

◆Added the commands "ip igmp authentication" on page 1451 and

"show ip igmp authentication" on page 1456.

◆Added "MLD Filtering and Throttling" on page 1469.

◆Added the command "mvr priority" on page 1482.

◆Added the commands "clear mvr6 groups" on page 1506 and "clear

mvr6 statistics" on page 1507.

◆Updated TTL range for the command "ethernet cfm linktrace" on

page 1592.

◆Added command "clear efm oam event-log" on page 1608.

◆Added information about configuring an address for tunnels in the

command "ipv6 address" on page 1665, and "ipv6 address eui-64" on

page 1667.

◆Updated syntax for the command "traceroute6" on page 1681.

◆Added the commands "ipv6 nd managed-config-flag" on page 1685,

"ipv6 nd other-config-flag" on page 1686, "ipv6 nd prefix" on

page 1690, "ipv6 nd ra interval" on page 1691, "ipv6 nd ra lifetime" on

page 1692, "ipv6 nd ra router-preference" on page 1692, and "ipv6 nd

ra suppress" on page 1693.

BOUT

HIS

UIDE

– 9 –

NOVEMBER 2012 REVISION

This is the second release of this guide. This guide is valid for software

release V1.2.0.0. It includes information on the following changes:

◆Removed information on Option 43 in "Downloading a Configuration File

Referenced by a DHCP Server" on page 115.

◆Updated parameter description in "Displaying Hardware/Software

Versions" on page 151.

◆Updated web page for "Setting the Time Zone" on page 171.

◆Updated parameter description in "Resetting the System" on page 177.

◆Added "Configuring Remote Port Mirroring" on page 188.

◆Added “Timeout Mode” under "Configuring a Dynamic Trunk" on

page 207.

◆Updated parameter list under "Configuring VLAN Groups" on page 228.

◆Added "Configuring VLAN Translation" on page 259.

◆Added parameters under "Configuring Loopback Detection" on

page 274.

◆Added parameters under "Configuring a Class Map" on page 326.

◆Updated parameters under "Configuring AAA Authorization" on

page 360.

◆Added parameters under "DHCP Snooping Configuration" on page 446.

◆Added parameter under "Configuring Ports for DHCP Snooping" on

page 449.

◆Added parameters under "Configuring LLDP Interface Attributes" on

page 461.

◆Added parameters under "Displaying LLDP Remote Device Information"

on page 470.

◆Added sfpThresholdAlarmWarnTrap to Table 34, "Supported Notification

Messages," on page 490.

◆Updated description for ERPS version 2 under "Ethernet Ring Protection

Switching" on page 523.

◆Added "PTP Configuration" on page 594.

◆Added parameters under "Configuring MVR Global Settings" on

page 658.

BOUT

HIS

UIDE

– 10 –

◆Added parameters under "Configuring MVR6 Global Settings" on

page 675.

◆Added RA Mode under "Configuring IPv6 Interface Settings" on

page 697.

◆Updated Command Usage section under "Specifying a DHCP Client

Identifier" on page 720.

◆Added "Configuring the PPPoE Intermediate Agent" on page 735.

◆Added IPv6 information under "Enabling Multicast Routing Globally" on

page 828 and "Displaying the Multicast Routing Table" on page 829.

◆Added information on PIM6-SM under "Configuring PIMv6 for IPv6" on

page 849.

◆Added information on PIM6-SM "Configuring PIMv6 Interface Settings"

on page 850.

◆Added "Configuring Global PIM6-SM Settings" on page 856.

◆Added "Configuring a PIM6 BSR Candidate" on page 858.

◆Added "Configuring a PIM6 Static Rendezvous Point" on page 859.

◆Added "Configuring a PIM6 RP Candidate" on page 861.

◆Added "Displaying the PIM6 BSR Router" on page 863.

◆Added "Displaying RP Mapping" on page 865.

◆Added "ptp e-latency" on page 962.

◆Added "ptp in-latency" on page 963.

◆Added "Synchronous Ethernet" on page 979.

◆Added "DHCPv6 Snooping" on page 1126.

◆Added "IPv6 Source Guard" on page 1140.

◆Added "lacp timeout" on page 1223.

◆Added "RSPAN Mirroring Commands" on page 1231.

◆Updated command set for ERPS under "ERPS Commands" on

page 1305.

◆Added RSPAN parameter to "vlan" on page 1344.

◆Added "Configuring VLAN Translation" on page 1364.

Andere Handbücher für ECS4660-28F

Inhaltsverzeichnis

Andere Edge-Core Schalten Handbücher

Edge-Core

Edge-Core ECS4810-12M-EUK Bedienungsanleitung

Edge-Core

Edge-Core AS6712-32X Bedienungsanleitung

Edge-Core

Edge-Core ECS5610-52S Bedienungsanleitung

Edge-Core

Edge-Core ECS5510-48S Bedienungsanleitung

Edge-Core

Edge-Core ECS4150-54T Bedienungsanleitung

Edge-Core

Edge-Core ECS4110-28P Bedienungsanleitung

Edge-Core

Edge-Core ECS1100-5P Bedienungsanleitung

Edge-Core

Edge-Core Wedge100BF-65X Bedienungsanleitung

Edge-Core

Edge-Core ECS4610-24F Programmierhandbuch

Edge-Core

Edge-Core ECS4100 Series Bedienungsanleitung

Edge-Core

Edge-Core ECS3510-10PD Programmierhandbuch

Edge-Core

Edge-Core AS7535-28XB Bedienungsanleitung

Edge-Core

Edge-Core ECS4620-28T Bedienungsanleitung

Edge-Core

Edge-Core ECS4150-28P Bedienungsanleitung

Edge-Core

Edge-Core ES4528V-38 Programmierhandbuch

Edge-Core

Edge-Core AS4610-30T Bedienungsanleitung

Edge-Core

Edge-Core ES4005V Bedienungsanleitung

Edge-Core

Edge-Core ECS4510-12PD Bedienungsanleitung

Edge-Core

Edge-Core AS7726-32X Bedienungsanleitung

Edge-Core

Edge-Core DCS520 Bedienungsanleitung

Edge-Core

Edge-Core AS4600-54T Bedienungsanleitung

Edge-Core

Edge-Core AS4610-54T Bedienungsanleitung

Edge-Core

Edge-Core ECS3510-26P Bedienungsanleitung

Edge-Core

Edge-Core ECS1100-5P Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung