Edge Products CS Bedienungsanleitung

Supplied Items Suggested Tools

1. CS or CTS Device

2. Arkon Windshield Mount

3. OBDII Cable

4. Mini USB Cable

5. Alcohol Wipe

6. Zip Tie Packet

• Flat head screwdriver

2 3

The OBDII port is a 16-pin connector like the illustration be-

low.

The OBDII port is located un-

der the dash below

the steering wheel.

The OBDII port is

placed in dierent

locations under the

dash for dierent

applications; refer to

the OBDII port loca-

tion drawing (left) to

help you locate your

OBDII port. If you are

unable to locate your

OBDII port, there may

be a sticker underneath

the steering column that may

explain where your OBDII is

located.

Once you’ve removed

the necessary panels,

connect the OBDII

cable to the OBDII

port, and route the

cable under the dash,

out the side panel, up be-

tween the door seal trim

and the edge of the dash.

Tuck the cable back as far

as you can as you route it

up to the dash.

Remove the panel on the

side of the dashboard to

provide access to route

the OBDII cable from the

OBDII port up to the top

of the dash.

*On some vehicles you may also

need to remove the panel directly

under the steering wheel.

*Note: Leave 6-10”

of cable exposed on

top of the dash so you

have room to posi-

tion the device.

OBDII PORT

Position the device

and the mount on

the windshield in the

desired location.

Pay attention to

where the suction

cup will mount on the

windshield.

Once you’ve identied

the suction cup position

on the windshield, use

the supplied alcohol wipe

to thoroughly clean the

area. After you’ve wiped

the area clean, let it dry

for 2-3 minutes.

Before you attach the

suction cup portion of the

mount to the window at-

tach it to the device. Insert

the tabs on the mount into

the slots on the back of the

device and slide up (CTS)

or to the side (CS) until it

stops.

*The mounting tabs are a tight t by

design to maintain a solid connection.

Next, insert the connector on the end

of the OBDII cable into the 16-pin

connector on the back of the device

(this is easier if done prior to mount-

ing the device on the window). The

connector only ts one way so be

sure that the locking tab is on the

bottom.

Note: The device will power on

automatically when it detects your

vehicle has started. If you wish to

power up the device without starting

your vehicle, ensure the key is in the

run position and touch the screen

(CTS) or a button (CS).

Once the alcohol has dried

you’re ready to attach the

mount to the wind-

shield.

UNLOCKED

Once you’ve locked the mount to

the windshield, use the adjustment

knobs to ne tune the viewing angle

and height of the the CTS/CS device.

CS/CTS QUICK INSTALL INSTRUCTIONS Step 1: Locate the OBDII Port Step 2: Connect/Route the OBDII Cable Step 3: Position the Device Step 4:Connect the Mount and OBDII Cable Step 5: Position and Lock the Device on theWindshield

VERTICAL ADJ.

KNOB

This knob will allow you

to adjust the viewing

angle and height of the

device up or down.

LOCKED

You’ll notice that the mount has

a locking tab. This tab creates the

suction that will lock the mount

to the windshield. Make sure

the lock is in the “Unlocked”

position. Position the

mount where you’ve

cleaned the windshield,

press rmly, and push the tab to the

“Locked” position.

VARIABLE ANGLE ADJ

KNOB

This knob will allow you to ad-

just the viewing angle of the

device in both horizontal and

vertical fashions. Use it to ne

tune your viewing angle.

OBDII LOCATIONS

After you’ve locked the mount and the CS/CTS device is

in place on your windshield, sit back in your drivers seat

and make sure the viewing angle is as desired. Check

to make sure the device doesn’t create a blind spot that

may impair your view of the road/trac/pedestri-

ans from the drivers seat.

After positioning the device

and the mount, remove any

slack in the OBDII cable and

coil it behind the side panel

you removed earlier. Use the

supplied zip ties to secure the

coiled cable from moving or

falling down under the dash, or

interfering with pedal operation.

Replace all panels removed during

installation

For Operating Instructions and trouble shooting please refer to the User Guide found

in the folder packet that came with your CS or CTS package. For additional questions

not found in the User Guide you can call:

Edge Products Technical Support

Hours Mon-Friday

8:00 a.m. - 5:00 p.m. Mountain Standard Time

1-888-360-EDGE (3343)

Multiple accessories are available for the

CS/CTS device. Accessories include EGT

sensors, back-up camera, and vehicle-

specic custom mounting solutions.

For more information and pricing

please visit

VIDEO IN PORT (CTS ONLY)

CS/CTS DEVICE DESCRIPTIONS

Step 6:Verify Position and Viewing Placement

ACCESSORIES PORT

*Note: Some states prohibit mounting devices

that may obstruct your view. Please check local

and state laws to ensure compliance.

For alternate mounting options visit

www.edgeproducts.com or www.arkon.com

1. Main Menu button - The main menu button gives you access to the main menu.

2. Left Gauge - The left analog gauge. The displayed parameter for all gauges can be changed by simply

touching the gauge and choosing a dierent parameter from the list. Usethis menu to choose a new PID,

change alert settings, and choose a new gauge color.

3. Up/Down Arrow Buttons - On the ATTITUDE gauge screen these buttons are used to toggle the power

level up/down. The EVOLUTIONgauge screen may use these buttons in future feature enhancements. The

INSIGHT uses these to adjust power levels when using EFILIVE™. In the menus these buttonsare used to select

the menu items and increase or decrease values.

4. Alert Indicator - The alert indicator light will illuminate (red) when an alert limit is exceeded. When this

light contains an “R,”it indicates that your Diesel Particulate Filter (DPF) equipped vehicle is performing a

regeneration cycle. If the light is blue and contains an “M”, your Maintenance Manager is letting you know a

maintenance item is ready to be serviced.

5. Power Level Indicator - The power level indicator represents the current power level. For example, “0”

represents stock. An “I” stands for Insight which produces no additional horsepower.

6. Back-down Indicator - (ATTITUDE with JUICE) The back-down indicator light will illuminate (yellow)

when the Juice module is decreasing power added by the device, and when approaching or exceedingthe

back-down set point limit.

7. Right Gauge - The right analog gauge.

8. Lower Left Gauge - The lower left digital gauge.

9. Center Gauge - The Center analog gauge.

10. Lower Right Gauge - The lower right digital gauge.

CTS LAYOUT

CS LAYOUT

654

THE MAIN MENU CONTAINS

THE FOLLOWING:

• View Camera - Thisgives you ac-

cess to the camera if installed on your

vehicle. (CTS only)

• Show alerts - This itemshows the

alert grid screen. *NOTE:This menu

only appears when there is an alert

active.

• Show Maintenance Due - This

allows you to quickly view which

maintenance items are ready to be

serviced. (Availableon cer tain models)

• Programming - This allows you to

program the vehicle to one of the pre-

tuned levels. (Evolution only)

• Juice Control - This gives you

access to the power and drive train

performance options through the

(Attitude only.)

• Diagnostics - This gives you the

ability to retrieve and clear trouble

codes, as well as other diagnostic

functions depending on vehicle.

• Options - This gives you access

to multiple device settings (i.e.

alert settings, sound duration,

backlight-autodim etc).

• Help - This is used to display product

information, vehicle information,

technical support tools, and contact

information.

• Hot Unlocker - This allows you to

add a HOT power level.(Attitude only)

MENU NAVIGATION BUTTONS

Both the CS and CTS devices provide you with the

following three buttons for navigating the menu

system:

Menu: The Menu button allows you to enter the main menu

(CS only). Once you are in the menu system you’lluse the Menu

button to return to the previous screen.

UP/Down Arrow: The Up/Down Arrow buttons will allow

you to toggle up or down through the menu options. Each

option will be highlighted as you toggle.

Enter: Pressing the Enter button will select the currently

highlighted option.

*Note: With the CTS device you can simply touch the option

you’dlike to select on the menu screen. As a touch screen

device it will automatically select the option you’ve touched

and advance you to the selected option screen.

CS/CTS MAIN MENU

CS/CTS ACCESSORIES

1. Up/Down Arrow Button - On the ATTITUDE gauge screen these buttons are used to toggle the power

level up/down. The EVOLUTIONgauge screen may use these buttons in future feature enhancements. The

INSIGHT uses these to adjust power levels when using EFILIVE™. In the menus these buttonsare used to select

the menu items and increase or decrease values.

2. Menu Button - The menu button gives you access to the main menu or can be used to exit out of a menu

screen.

3. Left Gauge - The left analog gauge. The displayed parameter for all gauges can be changed by pressing

the enter button, choosing the desired gauge, and selecting a dierent parameter from the list.

4. Alert Indicator - The alert indicator light will illuminate (red) when an alert limit is exceeded. When this

light contains an “R,”it indicates that your Diesel Particulate Filter (DPF) equipped vehicle is performing a

regeneration cycle. If the light is blue and contains an “M”, your Maintenance Manager is letting you know a

maintenance item is ready to be serviced.

5. Power Level Indicator - The power level indicatorrepresents the current power level. For example, “0”

represents stock. An “I” stands for Insight which produces no additional horsepower.

6. Back-down Indicator - (ATTITUDE with JUICE) The back-down indicator light will illuminate (yellow)

when the Juice module is decreasing power added by the device, and when approaching or exceedingthe

back-down set point limit.

7. Right Gauge - The right analog gauge.

8. Enter Button - The enter button when pressed from the main screen will allow you to change the gauge

parameters (PID, Alert Settings, and Gauge Color). In the menus it allowsyou to select the highlighted option.

9. Center Gauge - The center gauge.

Andere Handbücher für CS

Dieses Handbuch passt für folgende Modelle

Andere Edge Products Touch-Screen Handbücher

Edge Products

Edge Products CS Bedienungsanleitung

Beliebte Touch-Screen Handbücher anderer Marken

Elecro Engineering

Elecro Engineering Poolsmart Plus Montageanleitung

Johnson Controls

Johnson Controls IQ4 HUB Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems ET2270L Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems ET1002L Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems 3201L Bedienungsanleitung

Duratec

Duratec S15 Bedienungsanleitung

Crestron

Crestron TPMC-3SM Bedienungsanleitung

Racelogic

Racelogic MFD Touch Bedienungsanleitung

J2 580 Benutzerhandbuch

HAI

HAI OmniTouch 10p Bedienungsanleitung

panel

panel PC PSR108-FM Series Bedienungsanleitung

Tipro

Tipro FREE+ Bedienungsanleitung

Systemline

Systemline Commander Bedienungsanleitung

Interactive Technologies

Interactive Technologies Insite Bedienungsanleitung

GVision

GVision Legacy Bedienungsanleitung

BeiJer

BeiJer T21C-C24 Bedienungsanleitung

Advantech

Advantech ITM-5117 Series Bedienungsanleitung

Edge

Edge CS Bedienungsanleitung