EdgeStar AP14000HS Bedienungsanleitung

Welcome

Welcome and thank you for purchasing this EdgeStar Portable Air Conditioner.

We are glad you chose us. We take pride in knowing that, like our products,

our customer service will be just as dependable. Once you complete our easy

unit set up by following this manual, your portable air conditioner will provide you

years of great service.

Please save the original product packaging in case you need to safely transport

this portable air conditioner in the future.

For your reference:

Please write down the model and serial number here, as they are

needed to obtain service for your unit, if necessary. The two numbers

are on the label located on the back of your unit. You may also

want to staple your receipt to this manual. This will provide you with a

quick reference, as this information is needed for any service under

your warranty.

Model Number: ______________

Serial Number: _______________

Date Purchased: ______________

Need Assistance?

To better serve you, please do the following before contacting our customer service:

• Read this manual: it contains instructions to help you use and maintain

your portable air conditoner properly.

• If you received a damaged appliance: please contact the dealer that sold

you the appliance immediately.

• Read the section titled troubleshooting. This section will help you solve

common problems that might occur. If you do require service, our friendly and

efficient customer service representatives are available online via email at

[email protected] or by telephone at 1-866-319-5473.

could

• If the power cord on this unit is damaged it must be replaced by the manufacturer, its service agent or

qlified persons.

• This appliance is not inte

• • nded for use by children.

• This appliance is intended for domestic use only. Any other use may invalidate the warranty and might

be dangerous.

Make sure that the back of the unit is at least 4 inches or more away from a wall. Do not place

the unit in front of curtains or drapes to ensure they do not obstruct the air intake. Route the

power cord carefully to avoid a tripping hazard.

• If the power cord on this unit is damaged it must be replaced by the manufacturer, its service agent

or a qualified person.

• This appliance is not intended for use by children.

• This appliance is intended for domestic use only.

Warning

Remove the plug from

the socket if the unit is

not going be used for

a long period of time.

Do not wet the housing or

control panel.

Do not cover the air

outlet, while unit is in

use.

Improper handling may cause serious damage to the unit. Read this

manual carefully before operating the unit.

Do not allow children to play

with the controls or drop any

objects into the air outlet.

Do not place objects or

let any person sit on top

of the unit.

Always turn the unit off and

remove the power plug from

the socket when cleaning.

Do not attempt to remove any

part of the casing unless by an

authorized technician.

Use only the correct power

supply-AC115V/60Hz.

Do not operate the unit with a

damaged plug or loose outlet.

Warning

AP12000HS

17.3” X 30.91” X 14.96”

66.14 lbs.

1.6

10,000

Parts

1. Control panel

2. Air outlet

3. Handle hole

4. Caster

5.Airfilter

6. Air outlet hose

7. Air intake ( Evaporator)

8. Air intake hose

9. Water outlet drain

10. Power supply cord

Parts

1. Control panel

2. Adjustable Louvers

3. Handle

4. Caster

5. Air filter

6. Exhaust hose

7. Air intake (Evaporator)

8. Air intake hose

9. Drain

10. Power supply cord

Air vent cover is

manually adjustable.

On/Off

Timer Button

yard

and new batteries

Use only AAA batteries.

Remove the batteries if the remote control will not be used for a month or longerr.

Do not attempt to recharge the supplied batteries.

All batteries should be replaced at the same time; do not mix old and new batteries.

Do not dispose of the batteries in a fire, as they may explode.

Setting the Timer

If the unit is on:

• Press the timer button “

• Use the “ ”and “ ” buttons to set the

time (displayed in hours).

• After the selected time elapses, the unit will

automatically shut off.

Note: the word “ON” will appear next to

“ ” on the remote LCD when setting the

timer.

If the unit is off:

• Press the timer button “

• Use the “ ” and “ ” buttons to set the

time (displayed in hours).

• Then select which mode you want the unit to

automatically start in and make the

necessary adjustments.

• After the selected time elapses, the unit will

automatically turn on.

Note: the word “OFF” will appear next to

“ ” on the remote LCD when setting the

timer.

Power Button

Fan Speed Button

Mode Button

Operation

Cooling Dehumidifying

Note:

- Do not drop the remote control.

- Do not place the remote control in a

location exposed to direct sunlight.

- The remote control should be placed

3 feet or more away from any electrical

appliances.

Battery replacement: Remove the cover on the back of the remote control and insert the

batteries with the (+) and (-) ends pointing in the correct direction.

Timer/Temperature Set Buttons

Indication symbols on LCD:

Timer is adjustable from 1 to 24 hours by

pressing either the “

Temperature Display

Water Warning

-the machine will stop running

Dehumidifying mode

Cooling mode

Fan only mode

High fan speed

Med fan speed

Low fan speed

Air Conditioner Remote Control

All key funtions can be accessed

from the remote control.

Note: Adjustments made on the

unit’s control panel may not sync

with the remote contol’s LED.

Timer Setting Display

ON OFF

The diplay on the remote control is the set

temperature.

Used for adjusting the timer and

temperature.

When “” or “ ” button is pressed in

cooling mode, the temperature is

adjustable from 61ºF to 89ºF.

Heating

Heating mode

” or “ ” buttons.

When “” or “ ” button is pressed in

heating mode, the temperature is

adjustable from 61ºF to 80ºF.

Transmitting

-automatic function

.”

F°/C°

Press this button to switch the

temperature read-out between

Farenheit and Celsius

Note: Can only be toggled in

cooling and heating modes.

This portable air conditioner is designed to exhaust most or

all water condensed from the air (in cooling mode). In high

humidity situations, the internal water reservoir may fill. The

unit will automatically shut off and the water light will turn on.

Once the water is manually drained, the unit will operate as

normal.

Water Light

Speed

Mode

POWER Timer

WATER

Operation

Mode

This unit has 4 settings:

• Cooling • Dehumidifying • Fan • Heating

The settings are adjusted by pressing the mode button. Icons

on the LCD display will indicate which setting is currently being

used.

• Cooling Mode

When the cooling mode is selected, “ ”will show in

the LCD display. In cooling mode, room air is

cooled and hot air is exhausted to the outside

through the exhaust hose. Adjust the fan speed and

air temperature to suit your desired comfort level.

Note: The exhaust hose must vent outside the

room when using the cooling mode.

• Dehumidifying Mode

When dehumidifying mode is selected, “ ” will show

in the LCD displa y. The dehumidifying mode removes

• Fan Mode

When the fan mode is selected, “ ,” “ ,” or “ ” will

be shown in the LCD displa y, and air is circulated

throughout the room with no cooling.

Note: unit does not need to be vented in Fan mode

• Heating Mode

When the heating mode is selected, “

LCD Display

Timer Button

Fan Speed Button

Mode Button

Power Button Timer/Temp

Set Button

After turning the air conditioner off, wait 3 minutes before turning it back on again.

water from the air without cooling the room. If the

room temperature is below 77ºF, the fan speed will

be locked on “low;” above 77ºF, the fan speed is

adjustable.

Note: The exhaust hose is not required in

dehumidifying mode. Note that the internal

water tray will fill with water in this mode.

Power

To set the temperature in cooling or heating mode use the

“ ” and down “ ” buttons. The temperature setting

range is from 61

F- 89

Note: When in dehumidifying or fan mode,

temperature setting is not required or allowed.

Note: Inital setting is in ºF.

Temperature

Pressing both the timer/temp set buttons (“ ” and “ ”)

will switch the temperature

read-out between ºC and ºF.

Cancelling the Timer

You may cancel the timer setting at any time by

pressing the timer button once you have set the timer or

by pressing the power button.

Fahrenheit/Celsius

• Used for adjusting the timer and thermostat.

• The default display is room temperature.

• In cooling and heating modes, you can set the

temperature by pressing the “ ” and “ ” buttons.The set

temperature will be displayed for 10 seconds, then revert

back to room temperature.

• The timer can be set by pressing the “

• The timer is adjustable between 1-24 hours.

• Once the timer has been set, the adjusted time will be

displayed for 5 seconds, then the display willrevert back

to the displaying the room temperature.

Water Light

• The power button turns the unit on and off.

• When you first press the power button, the unit will begin to

operate in cooling mode. After you have used the unit, and

turned it off, it will default to the last used mode/settings

upon turning the unit on again. If power to the unit is

interrupted while the unit is running, the air conditioner

will restart itself in its last used mode/settings once power

is restored.

Note: This "auto restart" function will restart the unit after

power is restored. The compressor will resume after 3

minutes, if in use.

Timer/Temp Set Buttons

Temperature Display

Water Warning

-the machine will

stop running

Dehumidifying Mode

Cooling Mode

Fan Mode

High Fan Speed

Medium Fan Speed

Low Fan Speed

Timer Setting Display

ON OFF

Heating Mode

Transmitting

” will be

shown in the LCD display. In heating mode, room air

is heated and cool air is exhausted to the outside

through the exhaust hose. Adjust the fan speed and air

temperature to suit your desired comfort level.

Note: The exhaust hose must vent outside the room

when using the heating mode.

” and adjusting

the “ ” and “ ” buttons.

Fan Speed

The unit has 3 speeds: Low, Medium and High. Press the

speed button to toggle the speeds.

Fig. 1

Installation

Duct Connector Window Kit Connector

Exhaust Hose

2. Place one of the grated adapters(2) into one of the hole on flush side of the plastic window kit(1). Line

up the 4 holes in the grated adaptor(2) with the pilot holes in the plastic window kit and fasten them

together with a screw driver. Repeat for the other grated adaptor(2).

3. Install the plastic window kit(1) into your window. If necessary, use duct tape to better secure the window kit.

4. On the air conditioner, connect the duct connectors(4) (the connectors with the smaller slots) into the unit

by aligning the tabs inside the unit with the slots and snapping them together. (See Fig. 1).

Note: Once inserted, duct connectors cannot be removed.

5. Attach the window kit connectors(6) (the connectors with the larger slots) onto the exhaust hoses(5) by

stretching the hoses completely out and turning the window kit connectors(6) clockwise, screwing them

into the exhaust hoses(5).

6. Screw on the exhaust hoses(5) to the duct connectors(4) by turning them clockwise.

7. Move the air conditioner towards the window. Align the slots on the window kit connectors(6) to the tabs

on the grated adapters(2) and snap them together. (See Fig. 2)

8. To remove the window kit connectors(6) from the grated adaptors(2), push in the tabs on the grated

adaptors(2) and pull the window kit connectors(6) away from the grated adaptors(2)

9. To remove both the window kit connectors(6) and duct connectors from the exhaust hoses, twist the

connections counterclockwise. To remove the grated adaptors(2) unscrew the 8 screws(3).

10. The vent caps(7) may be installed on the grated adapters(2) (by aligning the slots with tabs and snapping

them together) when the air conditioner is not in use. (See Fig. 3)

1. Plastic window kit..............................2 pieces

2. Grated adapter..................................2 pieces

3. Screws..............................................8 pieces

4. Duct connector .................................2 pieces

5. Exhaust hose....................................2 pieces

6. Window kit connector........................2 pieces

7. Vent cap............................................2 pieces

Note: This unit can be used with one or two exhaust hoses. The exhaust hose(s) should alwaysbe used

in cooling mode. The air intake hose can be used to increase the cooling efficiency of the unit. If the air

intake hose is not used, simply cover one of the grated adapters on the plastic window kit with a vent cap.

1. Loosen the screws on the plastic window kit(1) and adjust the sliding kit to the width or height

of your window. Then tighten the screws to secure your adjustments to the window kit.

(See below images for setup examples)

Use lukewarm water

(below 104˚F) to clean

the appliance.

Replace the activated carbon filter

The activated carbon filter can notbe cleaned

and needs to be disposed of when cleaning the

pre-filter. EdgeStar sells replacement activated carbon

filters. Contact customer service via email at

service@edgestar.com or by telephone at

1-866-319-5473 to purchase additional activated carbon

filters.

Clean and reinstall the pre-filter

Dirt can be cleaned off the pre-filter

by washing it with a solution of soap in

lukewarm water.After cleaning the pre-filter,

allow it to air dry in shaded and cool place, then

reinstall. Clean the pre-filter

every two weeks if the air

conditioner operates in a

dusty environment.

Stop the appliance and remove

the activated carbon filter and the

pre-filter.

The activated carbon

filter attaches to the

standard pre-filter.The

activated carbon filter

removes smoke, odors

and other harmful

particles, while the

pre-filter removes dust.

It is necessary to clean or replace

the air filters periodically.

Clean as follows:

Maintenance

Maintenance and Storage

1. If you are not going to use this unit for a long time, be sure to drain the water from the

reservoir by removing the drain cap and the rubber plug.

2. Before storing the unit, run it in fan mode for a few hours to dry any moisture on the coils to

prevent mold.

3. Turn the unit off, clean the air filter and reinstall it.

4. Remove the exhaust hose and connectors and keep them in a safe place.

Never spray water onto the main

unit.

Wipe with a soft

dry cloth.

Turn off the appliance

first before disconnecting

from the power supply.

For Maximum Performance and Efficiency:

1. Do not cover the air outlet (exhaust) while in use.

2. Do not place the unit in front of curtains or drapes- to ensure they do not obstruct the air

intake.

3. Minimize the length of the exhaust hose.

4. Make sure the exhaust hose is as straight as possible.

5. Keep curtains, blinds or drapes closed during the sunniest part of the day.

6. Use the timer to operate the unit before it is needed. For example, set the timer to turn on

the unit in cooling mode for 3 or more hours to cool the room before you arrive. You may

want to operate the unit all day if you live in a warmer climate.

7. Minimize the heat sources (direct sunlight, computers, servers, people, etc.) in the room.

8. Close all windows and doors.

9. Use the unit in a contained room. For example, a room with four walls and a roof, instead

of a partitioned studio, or warehouse.

10. Make sure the unit is on a level surface.

11. Minimize the amount of humidity in the room. For example, adding a dehumidifier.

12. To prolong the compressor's life, please wait at least 3 minutes before turning the unit

back on after shutting it off.

13. Inspect and keep the pre-filters clean by cleaning regularly.

14. Inspect and replace the activated carbon filters regularly.

15. Perform routine maintenance.

Optimizing Performance

Troubleshooting

Why is my air conditioner not functioning at all?

oMove the air conditioner to another outlet, and test the outlet with a voltage tester or another appliance

that is known to be non-defective. If the outlet is bad, contact an electrician and move the air conditioner to

another outlet.

oIf the remote will not work, first, check the batteries. The control panel may be unplugged from the circuit board.

Contact customer service to repair.

Why is my air conditioner not cooling at all?

oThe unit should be in a room where the ambient temperature is below 95˚F . If the ambient temperature is

above 95˚F, the unit will likely not blow cold air but is not defective. Follow the below steps to increase the

efﬁciency of your unit’s compressor:

oMinimize heat in the room.

oMinimize the size of the area to be cooled (close doors and windows).

oClose curtains or pull down blinds; minimize direct sunlight into the room.

oRemove additional heat sources such as computer equipment (servers), etc.

oRun the unit before it is needed (e.g., run the unit in the morning before the area gets hot, and

continue to run the unit all day long in order to maintain a low temperature).

oUse more than one unit or a larger unit to cool the area.

oRemove the exhaust hose and run the unit for 5 minutes. Stick your hand in front of the exhaust and then

in front of the internal air louvers. Is the exhaust noticeably hotter than the interior air? If so, the unit is not

defective; follow the above steps to maximize efficiency of your unit’s compressor.

oIf your unit has a filter, the filter may be dusty or otherwise blocked. Clean the ﬁlter or contact customer

service to replace if necessary.

oCheck to make sure the air intake or exhaust ports are not partially obstructed. If they are, remove the

obstruction.

My unit turns on, but one of the fans is not turning or makes a loud noise? (Exhaust and evaporator fan)

oIf the fan spins freely while the unit is off, but does not spin when the unit is on, then the probable

cause is a loose wire from the fan motor to the circuit board, or a faulty fan motor. Contact customer

service to replace faulty wiring or fan motor.

oIf the fan does not spin freely, then the probable cause is a broken fan, or a foreign object has

jammed the fan. Contact customer service if fan is broken, or unplug unit and attempt to remove

foreign object.

oThe air conditioner may not be receiving electrical power. Press the test/reset buttons on the LCDI power

cord.

Andere Handbücher für AP14000HS

Inhaltsverzeichnis

Andere EdgeStar Klimaanlage Handbücher

EdgeStar

EdgeStar AP8000W Bedienungsanleitung

EdgeStar

EdgeStar AP10000HW Bedienungsanleitung

EdgeStar

EdgeStar AP410W Bedienungsanleitung

EdgeStar

EdgeStar AP14003W Bedienungsanleitung

EdgeStar

EdgeStar AP13500G Bedienungsanleitung

EdgeStar

EdgeStar MSPLIT12000W Bedienungsanleitung

EdgeStar

EdgeStar ap12000s Bedienungsanleitung

EdgeStar

EdgeStar AP1200S-1 Bedienungsanleitung

EdgeStar

EdgeStar AP8000W Bedienungsanleitung

EdgeStar

EdgeStar AP12000HS Bedienungsanleitung

EdgeStar

EdgeStar AP16000G Bedienungsanleitung

EdgeStar

EdgeStar AP12000S-1 Bedienungsanleitung

EdgeStar

EdgeStar AP12000S-1 Bedienungsanleitung

EdgeStar

EdgeStar AP12000HS-1 Bedienungsanleitung

EdgeStar

EdgeStar AP16000G Bedienungsanleitung

EdgeStar

EdgeStar AP310SS Bedienungsanleitung

EdgeStar

EdgeStar AP12005ECO Bedienungsanleitung

EdgeStar

EdgeStar AP14001HS Bedienungsanleitung

EdgeStar

EdgeStar PAC801W Bedienungsanleitung

EdgeStar

EdgeStar AP10002BL Bedienungsanleitung

EdgeStar

EdgeStar AP10001B Bedienungsanleitung

EdgeStar

EdgeStar AP10002BL Bedienungsanleitung

EdgeStar

EdgeStar AP13000W Bedienungsanleitung

EdgeStar

EdgeStar AP420HS Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung