Edgewater Networks EdgeMarc 4550 Bedienungsanleitung

Page 1 of 6

EdgeMarc 4550

Networking Gateway

Quick Start Guide

Version 1.0

201-4550-001

Page 2 of 6

Before You Start

Please read this guide thoroughly as it describes the basic installation of

the device. Additional configuration needed to deploy the device in a

specific environment can be performed with the help of online help.

This guide also provides an example of a typical 4550 deployment that

can be used as a guideline for your installation.

Requirements for Installation

•A computer with a web browser such as Microsoft Internet Explorer or

Mozilla Firefox or any other browser of your choice

•At least two Ethernet cables

Page 3 of 6

Instructions

Step 1 !Connecting the Cables

1. Connect one end of an Ethernet cable to local LAN port 1 of the 4550. This port can be

seen in the area “B” of the above diagram. Connect the other end of the cable to your

computer’s Ethernet port.

2. Connect an Ethernet cable between the Ethernet WAN port of the 4550, shown in the

above diagram as “C,” and the Ethernet port on a router or a modem.

3. Plug one end of the power adapter into an AC outlet and the other end into the power

receptacle on the 4550, shown in the above diagram as “A”. Make sure that the power

and status LEDs, shown in the diagram below as “A” and “B”, are solid green after a

short while.

Page 4 of 6

Step 2 !Configuring the EdgeMarc

1. The EdgeMarc device comes preconfigured with a local LAN address of 192.168.1.1 and

a subnet mask of 255.255.255.0. Configure your computer Ethernet adapter’s IP

address to any address other than 192.168.1.1 in the same subnet mask, for example

192.168.1.2.

If using a LAN switch then the switch must support 100Mbps full duplex.

2. Launch a web browser on the PC and enter the following URL: http://192.168.1.1 and hit

enter

3. The following login window should appear:

4. Enter “root” in the “User name” field and “default” in the “Password” field.

5. The “System” page should appear next. If you should see the "message of the day"

instead, just click on the System link under “Configuration Menu” to get to the “System”

page.

6. From the “Configuration Menu” on the left configure the following:

•“Network” – To configure WAN and LAN ports

•Optionally configure “DHCP Server” to suit your needs.

Page 5 of 6

Step 3 !Plan Your Configuration

The EdgeMarc 4550 can be deployed as a gateway router in a network. It can also be deployed

in a network behind an existing firewall. Based on your deployment criteria, consult the following

documents for further configuration:

•EdgeMarc 4550 Hardware Installation Guide

•VoIP Operating System (VOS) for EdgeMarc User Manual

Helpful Hints

Although not recommended, the 4550 and IP phones can be installed behind an existing

enterprise firewall. In this instance the firewall will have to be configured to allow access to and

from the 4550’s public IP address for the following ports:

Port Type

Firewall Ports to Open

UDP

161 (SNMP) and 162 (SNMPTRAP)

RTP

1056 to 1255

TCP

SSH TCP 22 for remote management & TCP 80 for WAN

configuration-downloads

Telnet

FTP

TCP 21 for stateful TCP-session control from 4508T4W to

Edgewater FTP server

MGCP

2427, 2429, 2432, and 2727

NTP ¬

123

SIP

5060 and 5075

IP phones normally point to a local NTP server for their time reference. The NTP port 123

needs to be opened if your network does not have an NTP server.

Please Note: Traffic shaping for this configuration is only available if the enterprise data

devices are also installed behind the 4550.

Page 6 of 6

The web page configurations for the various 4550 deployments are shown below. The two darker-

shaded rows indicate the minimum configuration required for each deployment.

4550

GUI Configuration

Page

4550 as

Gateway

Router

4550 within existing

infrastructure

4550 behind an existing

firewall

Network

Yes

VoIP/ALG

Yes

NAT

Yes

Optional

Yes

Firewall

Yes

Optional, but

recommended

Optional, but

recommended

DHCP

Yes

Yes (but should be

disabled if DHCP server

already exists)

Yes (but should be

disabled if DHCP server

already exists)

Traffic Shaper

Yes

Optional (depends on

network topology)

Traffic Simulator

Only for

testing

Only for testing

System

As needed

Please visit our website at www.edgewaternetworks.com or contact the Edgewater Technical

Assistance Center at 408.351.7255 for additional information or assistance.

Edgewater Networks, Inc.

2895 Northwestern Parkway

Santa Clara, CA 95051

Phone: (408) 351-7200

[email protected]

Converged Networking. Simplified.

Andere Handbücher für EdgeMarc 4550

Inhaltsverzeichnis

Andere Edgewater Networks Tor Handbücher

Edgewater Networks

Edgewater Networks 200AE1 Bedienungsanleitung

Edgewater Networks

Edgewater Networks ATT110900764 Stücklistenhandbuch

Edgewater Networks

Edgewater Networks 4610W Handbuch

Edgewater Networks

Edgewater Networks EdgeMarc 250W Bedienungsanleitung

Edgewater Networks

Edgewater Networks EdgeMarc 4552 Bedienungsanleitung

Edgewater Networks

Edgewater Networks EdgeMarc 4550 Handbuch

Edgewater Networks

Edgewater Networks EdgeMarc 250W Bedienungsanleitung

Edgewater Networks

Edgewater Networks 200AE1 Bedienungsanleitung

Edgewater Networks

Edgewater Networks EdgeMarc 6400LF2 Bedienungsanleitung

Edgewater Networks

Edgewater Networks 4610W Bedienungsanleitung

Edgewater Networks

Edgewater Networks EdgeMarc 250W Handbuch

Edgewater Networks

Edgewater Networks 200AE2 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung