Edimax ES-3116RE+ Bedienungsanleitung
16-Port 10/100Mbps
Smart Switch
(VLAN, Trunking & Fiber Option)
ES-3116RE+
User’s Manual
FCC Class B Certification
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following conditions:
1.This device may not cause harmful interference, and
2.This device must accept any interference received, including
interference that may cause undesired operation.
Warning!
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from the one which the receiver is connected to.
• Consult the dealer or an experienced radio/TV technician for
help.
You are cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void your
authority to operate the equipment.
1.Introduction
Congratulations on your purchase of this 16-port Smart Fast
Ethernet Switch. This high performance switch provides sixteen
fast ethernet ports to segment network traffics, extend fast ethernet
connection distance, and convert data packets between different
transmission speeds.
This Switch provides sixteen shielded RJ-45 ports. These are
10BaseT/100BaseTX Auto-negotiation ports.
This switch utilize stored-and-forward switching architecture
that filters and forwards data after the complete data packet is
received and examined to be free of errors. With one set of status
LEDs for each individual port, the switch operation status can be
easily monitored.
It’s rackmount design that can be mounted on the industrial
standard 19 inches rack in the enterprise wiring center.
This switch supports both full & half duplex on all ports which
are able to provide 200Mbps of bandwidth to the connected devices,
with auto-negotiation providing smooth migration from Ethernet to
Fast Ethernet. It also supports backpressure and IEEE 802.3x
advanced flow control capability that can reduce congestion and
prevent packet loss.
And it offers advance features :
VLAN : Port based VLAN allows you to set virtual
LANs within your network
Trunking : Reduce the bottleneck between swtiches
Fiber Option : Provide one fiber module option
2.Features & Specifications
(1) Features
Comply with IEEE 802.3 10BaseT and IEEE 802.3u
100BaseTX Standards.
Provide 16 UTP ports with 10/100Mbps Auto-Negotiation.
Provide one uplink port which can connect to another
hub/switch using a normal UTP cable
One 100Mbps Fiber-SC/ST module option (Support
Full/Half Duplex)
Support IEEE 802.3x compliant full-duplex flow control,
half-duplex flow control
Full wire speed on every port.
Support Port-based VLAN
Support 2 Trunking Group
Standard 19” rackmount size.
Support store-and-forward switching architecture.
(2) Specifications
Standards : IEEE 802.3 10BaseT and IEEE 802.3u
100BaseTX
10/100Mbps Ports : RJ-45 x 16
Uplink Port : RJ-45 x 1
100Mbps Fiber-SC/ST Port : Optional
Switching Architecture : Store and Forward
MAC Address : 8K
Buffer : 512Kbyte
Flow Control : Back pressure and IEEE 802.3x
VLAN : Port-based VLAN up to 16 groups
Trunking : 2 groups
N-Way Auto-Negotiation : on all ports
Full-Duplex / Half-Duplex : on all ports
Switch LED : Power
Port LEDs : Link/Activity, 100M, Collision/Full-Duplex
Power : 100~240V AC, full range internal power
Emission : FCC Class B , CE Mark , C-tick
3.Package Contents
One Fast Ethernet Switch
One Power Cord
One User’s manual
Rackmount accessories
4.Physical Description
(1) Panel
Front View
Control Button
LED
Rear View
I
o
SWAC 100-240V
POWER
Power Connector
Power Switch
RJ-45 Connectors
Expansion Slot
LED/Button Panel
Power LED
Setup
Buttons
Setup Functions
Normal : Link / Activity
Setu
p
: Status
Normal : 100Mbps
Setu
p
: Port
Normal : Full Duplex / Collision
Setu
p
: Grou
p
(2) LED
LED Status Description
On Power is supplied
System Power Off No Power
On Collision detected in
this segment
FUL/COL
(Full Duplex/Collision) Off No Collision
On A valid link is
established
Flash Data packets
received
LNK/ACT
(Link/Activity)
Off No link is established
On This port run at
100Mbps
Normal
Port
100M
(100Mbps) Off No connected or run
at 10Mbps
On This group is in
setting mode
Group Off This group is not in
setting
On This port is in setting
mode
Port Off This port is not in
setting mode
On This port is selected
Setup
Status
Status Off This port is not
selected
On VLAN is in setting mode
VLAN Off VLAN is not in setting mode
On Trunking is in setting mode
TRUNK Off Trinking is not in setting mode
On Speed is in setting mode
10/100M Off Speed is not in setting mode
On Full/Half duplex is in setting
mode
FULL/HALF Off Full/Half duplex is not in
setting mode
On Save function is in setting
mode
Setup
Function
SAVE Off Save function is not in setting
mode
5.Installation
(1) Operating Environment
This 16 ports smart switch must be installed and operated
within the limits of specified operating temperature and humidity
(see previous section under Specifications). Do not place objects on
top of the unit. Do not obstruct any vents at the sides of the unit. Do
not position the unit near any heating source such as heater, radiator,
or direct exposure to sun. Prevent entering of water and moisture
into the unit. If necessary, use dehumidifier to reduce humidity.
(2) Connecting network devices
The RJ-45 ports on the switch are designed as MDI-X ports
which allow using straight-through cables to connect this switch to
workstation or hub’s uplink port (MDI). A crossover cable must be
used to connect the switch directly to a hub’s regular port.
Connect one end of the network cable to the RJ-45 port on the
front panel, and connect the other end of the network cable to the
RJ-45 port on the network device. Follow the same procedure to
connect all the RJ-45 ports of the switch. The UTP network cables
must comply with EIA/TIA 568 specifications and Category 5
standard for 100Mbps data transmission. Maximum length, using
UTP cable, between the switch and connected device is 100 meters
(300ft). Once the network cable is connected to both ends and the
attached network device is powered on, the green LNK/ACT LED
should be lit.
An uplink port is located right next to the 16th port of this switch. The
uplink port is a shared port with the 16th port but provides the MDI
connecting to another hub/switch using regular straight-through cables.
Otherwise if you have bought our fiber option module that you can expansion to 1.5k
meters (5000ft) between the switch and connected device.
(3) Connecting the power
Connect the power cord to the power socket on the rear panel of
the unit. Connect the power cord to the power outlet and turn on
power switch. The Power LED on the front panel should be lit.
6.Advance Configuration
This switch provides advance features which offer you more
flexibility in setting up your network. The following section explain
how to setting up the VLAN, Trunking, Speed and Full/Half duplex
modes.
(1) VLAN
Virtual LAN (VLAN) is a logical subgroup within a local area
network which can be configure through port configuration. VLAN
can be configured to optimize traffic or to isolate specific
workstations for reasons of security or convenience. Each VLAN
you configure behaves as an isolated broadcast domain just as if it
were a separate switch. There is no communication between ports on
the separate VLANs unless the VLANs are connected by an external
router.
VLAN Configuration
This Switch provides sixteen VLAN groups. Please refer to the
following procedure to configure VLAN：
VLAN Group 3
VLAN Group 2
VLAN Group 1
Step 1. Press the Function button until the VLAN LED is on.
Step 2. Press the Group button to scroll between the VLAN groups 1 to 16.
Step 3. Press the Port button to scroll between the port 1 to 16.
Inhaltsverzeichnis
Andere Edimax Schalten Handbücher
Edimax
Edimax ES-5500G V2 Bedienungsanleitung
Edimax
Edimax ES-5800G V2 Bedienungsanleitung
Edimax
Edimax GS-5424PLC Bedienungsanleitung
Edimax
Edimax EK-2U2CA Bedienungsanleitung
Edimax
Edimax ES-1008PH Bedienungsanleitung
Edimax
Edimax EK-PA2C Bedienungsanleitung
Edimax
Edimax ES-5500G Bedienungsanleitung
Edimax
Edimax ES-3205P Bedienungsanleitung
Edimax
Edimax ES-516G+ Bedienungsanleitung
Edimax
Edimax 9-Port Desktop Ethernet Hub ER-5390S Bedienungsanleitung
Edimax
Edimax GS-1008PH Bedienungsanleitung
Edimax
Edimax EU-4306 Bedienungsanleitung
Edimax
Edimax SP-1101W Bedienungsanleitung
Edimax
Edimax ES-1024 Bedienungsanleitung
Edimax
Edimax ES-5800G V3 Installations- und Betriebshandbuch
Edimax
Edimax PS-3101P Bedienungsanleitung
Edimax
Edimax EK-16RE Bedienungsanleitung
Edimax
Edimax EK-UAK2 Referenzhandbuch
Edimax
Edimax EU-HB4M Bedienungsanleitung
Edimax
Edimax ES-5824PHG Bedienungsanleitung
