Effectrode Atomic Bedienungsanleitung
Specifications
•Operatesanywhereinthe worldfrom 110-
250VAC
•Supplied withcountry-appropriateIEC mains
powercableand 4pedalleads
•4x12VDC isolated outputs@1250mA
completely eliminatesearthloops
•One of theoutputscanbeconfigured topower
9VDC centernegativepedals
•Short circuit/overload protectionprotectsyour
tube pedals
•Powerrequirements: 110–240VAC IEC3pin
connector
•Dimensions: width7.5"; depth4.8";height 1.5"
•Weight: 1lb14oz(on Earth)
•Construction: Soliddie-cast aluminum box
•Finish: titanium-silverpowdercoat
Serial#
Copyright ©2011 Effectrode
â
AudiophilePedals
ISOLATEDPOWER SUPPLY
Owner’sManual
12 BroughtonCrescent,Barlaston,
Staffs,UK.ST12 9DB
www.effectrode.com
AT-1A
Introduction
Thankyouforpurchasing the Atomic IsolatedPower
Supply modelAT-1A.TheAT-1Ais specially
designedtomeetthedemandingpower
requirementsofourtube effectspedals.Properly
designedtube pedals requiremuchmorepower
than solid-stateeffectsbecauseofthe tubeheaters
and high voltage operation.Togetanidea,takea
lookatthesizeofthetransformers inside atypical
vintage tubeamp.TheAtomic generatesenough
ampstopowerupto4ofourminiaturetriodetube
pedals without compromising tonequality.
Thankyoufortrusting Effectrode tobeyoureffects
pedalcompany.Wewishyoumanyyears ofmusical
enjoyment fromthis very special, hand-built unit.
Phil Taylor–Designer
Notes
Wheninstalling theAtomic,ensureadequate
ventilation aroundtheenclosureanddonotobscure
the ventilation holes. Effectrode miniaturetubepedals
typically drawjustover1amp(1000mA)eachwhen
theyhavewarmed up andthis unitwill alsogetwarm
whenpowering severalpedals.Onpowerup,the
LEDson the frontpanelwill flashforafewseconds
whilethe tubeheaters warmup.Currentdrawis
higherfortubepedals during initialstart-up conditions,
asthe heaterfilamentresistanceis lowerwhen they
arecold.Asthe filamentwarmsup,theresistance
increasesand the tubeheaters begintogloworange.
It typically takesafewsecondsorthis tohappenand
afurtherfewsecondsis required fortheheaterto
beginwarmingthecathode tothe required
temperature.
Andfinally,herearethejumpersettingsfor9Vcenter
positivepedals.
WARNING!!! Before removing therear panelof this
unit,completelyisolateitfrom themainsby
disconnecting themainspower cableasthereare
hazardousvoltages withinthisunitwhichcould
causeinjuryordeath.Ifyou are uncertainabout
whatyou aredoing please seekadvicefrom a
qualifiedelectricalengineer.
Setups
The Atomic powering four Effectrode tube pedals.
The first poweroutput canbeusedtopower9Vcenter
negativepedals inadaisy-chainasshownbelow. Configuration
The Atomic can be configuredtopower9Vcenter
negativeorcenterpositivepedals using internaljumpers.
Toaccess the jumpers first make sure theunitis
disconnectedfrom mainspower outlet toavoidthe
possibilityofalethalelectric shock.Removethe six
screwson the baseofthepedalandremovethe
baseplate.The Atomic shipsinstandardconfigurationof
12Vcenterpositiveasshowninthefigurebelow.
Toconfigurefor9Vcenternegativepedals setthe
jumpers asshownbelow
Dieses Handbuch passt für folgende Modelle
1
Andere Effectrode Stromversorgung Handbücher
