EFILive CM2200 Bedienungsanleitung

Cindy Myers

Cummins 2010-2018

(CM2200 & CM2350B)

Quick Start Guide

EFILive, EFILive FlashScan and EFILive AutoCal are registered trademarks of EFILive Limited.

All other trademarks belong to their respective owners.

Cummins 2010-2018

(CM2200 & CM2350B)

Quick Start Guide

First published

18 December 2014

Revised

18 October 2018

Cummins 2010-2018 Quick Start

support@efilive.com - 1 - www.efilive.com

Contents

............................................................................................................3

Prerequisites....................................................................................................................3

Intended Audience.......................................................................................................3

Computer Knowledge...................................................................................................3

......................................................................................................4

Introduction......................................................................................................................4

CM2200 & CM2350B ECM Overview ..........................................................................4

RSA Digital Signature ..................................................................................................4

Software.......................................................................................................................5

Overview ..................................................................................................................5

Requirements...........................................................................................................5

Additional Support Resources......................................................................................5

CSP5 Cummins Switchable Programming....................................................................6

Logging Data................................................................................................................6

FlashScan/AutoCal Capacity and Tune File Sizes.......................................................6

Supporting Remote Customers....................................................................................6

Failed Flash Recovery Methods...................................................................................6

............................................................................................................8

2010-2018 Quick Start.....................................................................................................8

Finding the Correct Base File.......................................................................................8

Determine Current Calibration..................................................................................8

Match Calibration Requirements ............................................................................10

Editing a Tune File.....................................................................................................11

Licensing Requirements.............................................................................................13

Cummins 2010-2018 Quick Start

support@efilive.com - 2 - www.efilive.com

Dodge Cummins Tuning Option Enabled...............................................................13

VIN Licensing .........................................................................................................14

Flashing the ECM.......................................................................................................14

EFILive Scan and Tune..........................................................................................14

FlashScan V2.........................................................................................................16

AutoCal...................................................................................................................17

..........................................................................................................18

BBX Configuration.........................................................................................................18

Setting up FlashScan V2/AutoCal for Reading, Flashing and Logging using V8

Scan and Tune...........................................................................................................18

BBL (Black Box Logging) Configuration .................................................................18

BBR & BBF (Black Box Reading and Flashing) Configuration ...............................19

Switchable Tune Configuration...............................................................................19

Quick Setup............................................................................................................20

Move Tune and Log files from FlashScan V2/AutoCal to your PC.............................21

Cummins 2010-2018 Quick Start

support@efilive.com - 3 - www.efilive.com

Prerequisites

Intended Audience

EFILive Customers using the V8 Scan and Tune Tool software.

Computer Knowledge

It is expected that readers have a basic understanding of:

The Windows operating system;

Starting and using Windows applications;

Navigating folders using Windows Explorer.

Cummins 2010-2018 Quick Start

support@efilive.com - 4 - www.efilive.com

Introduction

This document is intended to assist EFILive customers with the basic operations

and steps necessary to work with 2010-2018 6.7L Cummins supported vehicles.

CM2200 & CM2350B ECM Overview

Due to the CM2200 and CM2350B ECM's restrictive architecture, Cummins 2010+

ECMs cannot be read via the OBD-II Port. These ECMs can only be read by

opening the ECM and soldering to the CPU debug port using expensive 3rd party

tools.

Customers will need to obtain a suitable base file for editing and flashing. A

selection of EFILive compatible base stock files are readily available on the

internet or custom files may be purchased through organizations that have the

necessary hardware and software to create personalized base files.

There are two ECM types; EFILive refers to these as CMD and CME.

Controller

Year

CM2350B (CME)

2013-2018

CM2200 (CMD)

2010-2012

Because you cannot read the existing tune in the ECM it is important you select

the correct base tune to suit your vehicle.

RSA Digital Signature

In early 2009 Cummins ECMs were manufactured with higher levels of security

consisting of an RSA Digital Signature on the calibrations. The RSA Digital

Signature does not prevent the flashing of stock tunes, it ONLY prevents the

flashing of modified tunes, so to flash a modified tune the Digital Signature must

be switched off.

The EFILive ECM flash process manages the removal of the Digital Signature via

OBD-II flashing in the following circumstances:

Controller

Flash Method

CM2350B (CME)

In vehicle and bench harness flashing.

CM2200 (CMD)

Bench flashing only.

CM2100 (CMC)

Bench flashing only.

In vehicle flashing for CM2100 and CM2200 controllers requires the BootRSA

Patch file process to remove the digital signature. Please refer to the Cummins

Boot RSA Patch User Guide.

Cummins 2010-2018 Quick Start

support@efilive.com - 5 - www.efilive.com

NOTE: The ECM must be fully operational and not in boot mode as a result of a

failed flash (error $0340) or forced boot mode. Where the ECM is in boot mode,

the unlock process is bypassed and two-step flash process is required to remove

the digital signature.

1. Recover the ECM by flashing a stock tune to restore the ECM to

operational mode.

2. Flash the ECM to remove the digital signature.

Software

Overview

EFILive presently has two major software versions (V7 and V8) that implement

different parts of the tuning and scanning process. The V8 software is undergoing

significant development and will eventually supersede V7 entirely for FlashScan

V2 customers.

Cummins customers must install both versions, the following table displays

Cummins 2010-2018 software functionality.

Feature

Scanning

OBDII Diagnostics

Reading

Flashing

Tune Editing

VIN License Management

Firmware Management

Requirements

The most recent Cummins software enhancements are available in the following

product versions:

EFILive V8.2.17 or later.

FlashScan V2 / AutoCal Firmware - V2.07.134 or later.

The latest software is available for download from the EFILive website here:

http://www.efilive.com/latest/cat/download-efilive

Additional Support Resources

If, after reviewing this guide, further assistance is required please contact the

EFILive Authorised Reseller from whom you purchased your product. They are

your first point of contact for EFILive support related inquiries.

If your question is in relation to the actual tuning of your vehicle (i.e. how to gain

performance, economy etc.) then please ask these questions on the EFILive

Forum (http://forum.efilive.com/). EFILive does not provide support or assistance

for the actual tuning of any supported vehicles.

Cummins 2010-2018 Quick Start

support@efilive.com - 6 - www.efilive.com

CSP5 Cummins Switchable Programming

EFILive's CSP custom operating systems for the Cummins ECM‘s allows

customers to be able to switch 'on the fly' between multiple tunes, all stored in the

ECM's flash memory. Refer to the specific user guide for your controller for

detailed instructions on how to upgrade your operating system.

Cummins 6p7L CM2200 CSP5 User Guide.pdf

Cummins 6p7L CM2350B CSP5 User Guide.pdf

Logging Data

EFILive’s Enhanced Data Logging (EDA) allows customers to log 45 individual

data parameters specifically chosen to complement tuning at up to 50 frames per

second using FlashScan V2/AutoCal Black Box Logging (BBL), V8 pass-thru

logging & V7.5 pass through logging.

EDA is only accessible to customers who upgrade to EFILive’s CSP5operating

system. Refer to the specific user guide for your controller for detailed instructions

on how to upgrade your operating system.

Factory scanning (data logging) of the Dodge Cummins ECM controllers is also

supported. Useful factory scantool data is very limited. EFILive recommends

users upgrade to CSP5/EDA for useful scantool data.

FlashScan/AutoCal Capacity and Tune File Sizes

FlashScan V2 has approx. 6MB of internal memory capacity for the storage of

tune and log files. Capacity can be extended using an SD card.

AutoCal has approx. 6MB of internal memory capacity for the storage of tune and

log files.

The tune file sizes for the CMD and CME controllers are significantly larger than

existing controllers which directly restricts the number of tunes that can be stored

on FlashScan V2/AutoCal internal memory.

Controller

Tune File Size

CM2350B (CME)

Approx. 3.5MB each

CM2200 (CMD)

Approx. 2.5MB each

Supporting Remote Customers

Due to the size of tune files, moving tunes on/off an AutoCal device will be

prevalent. EFILive recommends to those tuners using AutoCal for their end users,

that tune files are managed via the Quick Setup in order to manage device

configurations and minimize support issues.

Failed Flash Recovery Methods

In the event that an ECM fails during the flashing process, recovery methods exist

to restore the ECM.

In most instances, simply retrying the flash process will return the ECM to working

order.

In the instance where tuners apply security restrictions to a tune file, including

locking to the controller serial number, and the flash fails, you must try to recover

Cummins 2010-2018 Quick Start

support@efilive.com - 7 - www.efilive.com

the ECM with a file that has no security restrictions in place (e.g. stock tune)

before attempting to reflash a file with security restrictions.

If retrying the flash process does not return the ECM to working order, the Problem

Flashing a Controller and Controller Recovery knowledgebase articles provide

additional support resources.

Cummins 2010-2018 Quick Start

support@efilive.com - 8 - www.efilive.com

2010-2018 Quick Start

Finding the Correct Base File

The following instructions will determine the base tune file that should be used for

each vehicle.

EFILive does not provide stock tunes or modified tunes. There are a variety of

stock tunes available on the internet, or custom stock tunes can be purchased

through organizations that have the necessary hardware and software to create

personalized base files.

Determine Current Calibration

There are 3 methods to find the calibration details of the tune presently in the

ECM. Customers can choose which method best suits their needs.

V8 Scan and Tune

1. With FlashScan V2 or AutoCal connected to your vehicle and your PC, open

EFILive V8 Scan and Tune and select [F4: OBD] -> [F2: OBD].

2. On the Details tab use the Auto Detect button, or right click on the Right-click

to select engine-controller box and manually select the ECM.

3. Select the Retrieve All Information button to populate controller data.

4. Copy or record the Calibration ID to use in the match calibration requirements

step.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung