Egholm Park Ranger 2150 Bedienungsanleitung
Operator´s
manual
Hedge cutter
Park Ranger 2150
2Operator’s Manual Park Ranger 2150 Hedge cutter Operator’s Manual Park Ranger 2150 Hedge cutter
Dear Customer,
Congratulations with your new Egholm product
The Park Ranger 2150 is a Danish-designed and manufactured utility machine, which allows
you to take a very exible approach to maintaining outdoor areas.
Optimal use of your Park Ranger 2150 Hedge cutter
To ensure optimal performance from your Park Ranger 2150 Hedge cutter, please read this manual
carefully before using the machine. Failure to do so can result in personal injury and damage to the
machine.
Safety
The Hedge cutter is equipped with various devices to ensure optimal operational safety both
for the user and the surroundings. We ask you to pay particular attention to section 1.1 Safety.
The machine must only be serviced by professionals.
The Hedge cutter is designed only for use by professionals. On delivery, the user will receive
thorough training to become a competent operator. Do not lend the machine or tools to anyone who
has not been thoroughly trained and who has not read this manual carefully.
The operator’s manual should be considered a vital accessory to the machine and must remain with
it if the machine is sold.
Warnings
Some items in this operator’s manual are marked with this warning symbol.
The warning indicates areas where extra care must be taken to avoid personal
injury or damage to the machine and its accessories. The warning also explains
how you should pay special attention to the aspect in question.
Reservations
As it is the Egholm policy to make continuous improvements, we reserve the right to alter the
machine’s specications and equipment at any time without notice. Egholm accepts no liability for
errors or omissions in the operator’s manual.
Contact Egholm
Please do not hesitate to contact Egholm if you have questions of any kind regarding your new
Egholm product.
Best regards,
Egholm A/S · Transportvej 27 · DK-7620 Lemvig
T. +45 97 81 12 05 · F. +45 97 81 12 10
E-mail: info@egholm.dk · www.egholm.eu
Introduction
3Operator’s Manual Park Ranger 2150 Hedge cutter Operator’s Manual Park Ranger 2150 Hedge cutter
The Park Ranger 2150 Hedge cutter operates
quickly and effectively on hedges and bushes up
to 2,5 metres in height and on branch
thicknesses up to 20 mm (depending on the
species of tree). The Hedge cutter is xed at the
front of the machine and controlled from the
cab.
The Hedge cutter can easily be adjusted to trim
horizontally,
vertically or at any angle required.
During transport, the Hedge cutter is folded to
save as much space as possible.
Attach and detach the Hedge cutter in less than
a minute with no tools required.
When detached, the Hedge cutter rests on four
wheels and is extremely easy to store.
Contents
General information ..........................................................................5
1.1 Safety .................................................................................5
1.2 EC Declaration of Conformity ............................................................6
1.3 Technical data .........................................................................7
Operator’s manual ...........................................................................9
2.1 Assembly / Disassembly ................................................................9
2.2 Before start-up ........................................................................12
2.3 Start-up ..............................................................................13
2.4 Setting trimmer position ...............................................................14
Service and Maintenance ....................................................................18
3.1 Cleaning .............................................................................18
3.2 Maintenance ..........................................................................18
Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
4.1 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.2 Complaints ...........................................................................21
4.3 Disposal ..............................................................................21
Wearing parts ...............................................................................23
5.1 Wearing Parts - Park Ranger 2150 Hedge cutter ..........................................23
Notes .....................................................................................27
General information
5
Max. 10°
Ophold i knækområdet
er forbudt
Aufenthalt im Knickbereich ist verboten
Activities around the articulation point is forbidden
Ne séjournez jamais dans la zone d’articulation
Park Ranger 2150
1
2
3
4
Operator’s Manual Park Ranger 2150 Hedge cutter
1.1 Safety
NB
As it is articulated, the rear end of the
machine swings out when turning.
Make sure that no one stands near the
machine while it is in use.
(Picture 1)
Make sure no one stands close to
the machine while it is in use
To avoid the risk of personal injury,
stay clear of the cutting bar when it is
being lowered and tilted.
Cover the cutting bar when the
Hedge cutter is not in use or during
transport
Remove the cover immediately prior to
use. (Picture 2)
In the case of maintenance or repair,
always switch off the motor
The attachment motor must be
stopped before any adjustment,
maintenance or repair can be carried
out on the Hedge cutter.
Avoid roll-overs
Do not drive the machine in a place
where it can slide, tip or roll. Do not
drive on slopes with an incline of more
than 10 degrees. The tyre pressure
must be checked and adjusted to 1.5
bar (22 psi) when the Hedge cutter is
attached. Low tyre pressure increases
the risk of roll-overs. (Picture 3)
Transport
Only transport the Hedgecutter when
packed in transportation position.
(Picture 4)
Protective covering
Do not drive on slopes with an incline of more
than 10°
Ensure that no one stands in the working area
General information
Packed in transportation position
6Operator’s Manual Park Ranger 2150 Hedge cutter Operator’s Manual Park Ranger 2150 Hedge cutter
1.2 EC Declaration of Conformity
Manufacturer: GMR maskiner a/s
Address: Saturnvej 17 DK-8700 Horsens
Tel.: +45 75 64 36 11
hereby declares that
The machine: Cutter arm and Hedge cutter
Model: GMR Maskiner A/S
Type: Arm: Trim 2150
Knife: MB 130-3
· has been manufactured in conformity with the provisions of the Machinery Directive, Directive
2006/42/EC
Any alteration, rebuilding or addition of implements, accessories or other equipment not
manufactured by Egholm automatically results in the cancellation of type approval, CE approval,
any other approval, as well as any warranty on machine and attachments.
Unless otherwise agreed in writing between the operator, customer and Egholm, Egholm is the
data originator (data originator) of all data generated by the machine and attachments during use.
Place: Lemvig, Denmark
Date:
Signature:
Poul Møller Rasmussen
General information
7
12
Operator’s Manual Park Ranger 2150 Hedge cutter Operator’s Manual Park Ranger 2150 Hedge cutter
1.3 Technical data
Dimensions Attached Storage dimensions
Length (L)..............................3,500 mm.................. 1,000 mm
Width (W) ..............................1,600 mm.................. 1,600 mm
Height (H) incl. cab......................1,960 mm.................. 1,450 mm
Height (H) incl. roll bar...................2,000 mm
Technical data
TypeHP ................................................. TRIM2150/ MB130-3
Max. horizontal reach ..............................................2,500 mm
Cutting width...................................................... 1,300 mm
Horizontal cutting height .......................................300-2,100 mm
Vertical cutting height ............................................ 0-3,200 mm
Angle for cutting bar ....................................................270º
Max. branch thickness ................................................20 mm
Operating speed .................................................... 1-3 km/h
Weight................................................................130 kg
Hydraulic oil ................................Texaco Rando HDZ 68 or equivalent
NB
Specications may be changed without prior notice.
Information plate
(Picture 1+2)
General information
Type plate
Cutter
Type plate
Arm
Operator´s manual
9
2
4
5
3
1
6
Operator’s Manual Park Ranger 2150 Hedge cutter
2.1 Assembly / Disassembly
Delivery
The arm and cutter are delivered on one pallet.
(Picture 1)
Unpack both parts and place them on a plan surface
1. Check the arm, the top hydraulic cylinder must be in
out position (Hole in square pipe pointing up and down.)
(Picture 2+3)
2. Mount the cutter knife in the square hole, put in the
M10 bolt (Picture 4).
Mount and tighten the bolt with M10 nut.
Tighten the allen bolt and check the cutter can not
move at all from the cutter arm square pipe. (Picture 5)
3. Mount the hydraulic hoses. The hoses must be
guided below the cutter arm square pipe. (Picture 6)
The Hedge cutter is now ready to mount on the Basic
machine.
Operator’s manual
The arm and cutter are delivered on one
pallet
Hole in square pipe pointing up and down
Cylinder in out position
Mount the cutter knife in the square hole,
M10 bolt
The hydraulic hoses must be guided
below the cutter arm square pipe
Hole in square pipe pointing up and down
Tighten the allen bolt. Check the cutter can not
move at all from the cutter arm square pipe.
10
1
2
4
3
Operator’s Manual Park Ranger 2150 Hedge cutter Operator’s Manual Park Ranger 2150 Hedge cutter
2.1 Assembly / Disassembly -
continued
1. The locking handle on the A-frame of the
basic machine must be in the unlocked position.
(Picture 1)
Tips!
Raise the Hedge cutter front wheels free of the
ground and lower the support struts, so that the
Hedge cutter A-frame is angled back.
This makes it much easier to ‘catch’ the A-frame
when attaching. (Picture 2)
2. Drive the machine right up to the A-frame of the
Hedge cutter so the A-frames t into each other.
(Picture 3)
3. Raise the A-frame using lever A on the left-hand
side of the Basic machine until the Hedge cutter
is freely suspended above the ground. (Picture 4)
4. Switch off the engine.
Locking
Lever A
Unlocked A-frame
Support strut lowered
U
n
l
o
c
k
e
d
Operator’s manual
Andere Handbücher für Park Ranger 2150
18
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Egholm Trimmer Handbücher
