EGi DOMOS2 Bedienungsanleitung
40100
Remote control
www.egiaudio.com
Avda. Almozara, 79 50003 ZARAGOZA - Spain Phone +3 976 0 53 56 Fax +3 976 0 53 5 http//: www.egiaudio.com e-mail: info@egiaudio.com
Users Manual
English
005180
Thank you for choosing the
EGi DOMOS2 Universal
Remote Control. It will allow
you to control your home
appliances, as well as your
EGi Audio & Domotic System.
Please read carefully before
using the system and save this
manual for future reference.
EGi DOMOS2 Universal
Remote Control can program
codes from other remote
controls (TV, VCR, DVD, audio
equipment, etc.) by the
learning process or selecting
them on a code list.
EGi DOMOS2 Universal
Remote Control has a LCD
backlight touch-screen with
56 buttons to control each
device.
The advanced functions
allow you to program up to
60 commands at the touch
of a button.
CHAPTER 1
Getting started 4
40100 Remote control 4
CHAPTER 2
Before use 6
Code/Learn button 6
Manual code selection 6
Automatic code selection 7
CHAPTER 3
Code learning function 9
Code learning process 9
LCD Edit mode: Device buttons 10
Delete codes and devices 11
MACRO Function 12
Reset to initial codes 14
CHAPTER 4
EGi - Audio 15
EGi - Domotics 17
CHAPTER 5
Option settings 19
APPENDIX A
Technical specifications 23
APPENDIX B
Problem-solving chart 24
1
2
3
4
5
7
6
www.egiaudio.com
4
Getting started
Before using the 40100 Remote Control, please make sure that the package contains the following components:
•1 x 40100 Remote Control.
•1 x User’s Manual.
•1 x Pre-Programmed Code List.
•3 x AAA 1.5 V Alkaline Batteries.
If the package does not include any of these components, please contact your installer or the EGi
Customer Service.
BATTERY ORIENTATION
Open the battery lid that is on the backside of the remote control.
Chapter 1
1IR Emitter to transmit the signals to the device to be
controlled.
2Ambient light sensor to detect the light in the room
and turn the backlight on, if necessary.
3LCD Touch-screen to display all control buttons of
the device to be controlled.
4Backlight. If there is not enough ambient light, the
remote control will be illuminated during use and 90
seconds after pressing a button.
5Device buttons to select the device to be controlled.
6Connector to transfer settings between two remote
controls using a wire (not included).
7IR Receiver to use during the learning mode.
•Inside the battery compartment there are symbols showing in which direction
the batteries should be placed. Carefully follow these directions.
•Do not mix new and old batteries.
•Replace all batteries at the same time.
40100 Remote control
1 2 3 4
5 6 7 8
www.egiaudio.com
5
40100 Remote Control will allow you to control your EGi Audio & Domotic System. You will also be
able to control all home appliances, as well as your TV, DVD, audio equipment, and radio receiver with
your 40100 Remote Control.
To select the device or system that you want to control, press the icon on the lower part of your remote
control display.
1Select the TV device.
2Select the satellite receiver/cable.
3Select the video device (VCR).
4Select the DVD device.
5Select the audio equipment.
6Select other audio sources.
7Select the EGi domotic system.
8Select the EGi audio system.
www.egiaudio.com
6
Before use
Before using the 40100 Remote Control, you must set it to ensure the correct transmission to the devices
that are going to be controlled.
The setting can be done by introducing the CODES:
•Manual: Introducing the number (from the code list) assigned to the device to be controlled.
•Automatic: Allowing the remote control to interact with the device to be controlled.
You may also set the device through the LEARNING process.
Code Learn button
Press the CODE button for 3 seconds to access to the confirmation screen. Then press each number
in any order to access to the next screen. Press the and buttons to select one of the following
options:
•CODE: Automatic setting. Your remote control must be included on the code list.
•LEARN: If your remote control is not included on the code list, you must prerecord the codes
manually. To do so, put the remotes in front of the other.
Manual code selection
This function allows you to set your 40100 Remote Control and make it work as one of the remotes
included on the attached list.
Chapter 2
1Select the device to be programmed for instance, TV.
2Press and hold the CODE button for 3 seconds to access to
the confirmation screen.
3Press each number (2, 4, 6, 8) in any order. Start to use the
PRE-CODE function.
www.egiaudio.com
7
Automatic code selection
4Press and buttons to select the desired options until
you find CODE. Press and access to the code page.
5Press the 4-digit code manually.
NOTES:
•Some codes included on the list are not specific to one remote control model. You must select the
one that best adapt for your model.
•If a code is not included on the Manufacturer’s Code List, the screen will display ERROR when
introducing that code.
EXAMPLE:
Should you wish to control the two televisions that you have at home (TV1 and TV2) with your 40100
Remote Control, follow these steps:
1Assign the TV1 to the TV device button. Please see “LCD Edit Mode: Device buttons” to introduce
the 4 codes, and follow the steps.
2Assign the TV2 to any of the device buttons except DOMOTICS and EGi AUDIO; for instance,
SAT/CBL. Follow the same steps as in TV1.
Press the TV button any time you want to control the TV1. Press the SAT/CBL button any time you
want to control the TV2.
Please note that your remote control may not be listed as there are many manufacturers
and remote control models available on the market. If so, please see “Manual code
selection” & “Code learning process”.
1Manually turn on the device to be controlled.
2Select the device to be controlled (TV, SAT, AUDIO) on your
40100 Remote Control.
3Press CODE for 3 seconds.
www.egiaudio.com
8
4Press each number (2, 4, 6, 8) only once in any order.
5Press the button to select CODE.
6Press AUTO. You will listen to a beep while AUTO and OK
blink.
7When the device (that is being controlled) turns off, press
any key of the remote control.
8Press or until the device you want to control turns on.
9Press the button to ensure the correct operation.
10 Press DISPLAY to see the code of your device.
11 Press the OK button to confirm the selection.
www.egiaudio.com
9
Chapter 3
Code learning process
If we assume that you want to program the TV remote control on the EGi 40100 Remote Control, then
put both remotes together as shown in Figure 6 and proceed as follows:
1Keep the CODE button pressed for 3 seconds to access to
the confirmation screen.
2Press each number (2, 4, 6, 8) only once in any order.
3Navigate through the menu options using the and
buttons until you find the LEARN option.
4Press the button to confirm this option.
5Press the button of the device to be controlled (TV, SAT/CBL,
VCR, DVD, Audio, etc.) for instance, DVD.
Code learning function
EGi 40100 Remote Control allows you to learn the codes from your existing remote control, for instance
TV, without using the Manufacturer’s Code List.
Before learning the codes from your existing remote control, please read carefully the following:
1Before learning the new codes, delete the existing ones from the remote control. For instance, if
you want to control your living room TV instead of your kitchen TV, delete first the commands of
your kitchen TV.
2This learning process does not work with all remote controls on the market.
3Not all of the EGi 40100 Remote Control keys can be programmed: CODE SETUP KEY, DELETE
KEY, MACRO KEY and SYSTEM SETUP.
www.egiaudio.com
10
1Keep the remote control button pressed for at least 3 seconds
to access to the confirmation screen.
2Press each number (2, 4, 6, 8) only once in any order to
access to the selection screen.
3Press the button that you want to change on the remote control
page. Press repeatly to select any of the available options.
4Press KEY to display all the available icons on the LCD screen.
Repeat step 3 until all changes are made.
5Once you have defined the screen, press OK to confirm
changes. If you do not want to save changes, press EXIT.
LCD Edit mode: Device buttons
The edit mode allows you to define the touch screen so as to match it with your existing remote controls.
6The button on the 40100 Remote Control blinks. Press
the same button on the remote control until it stops blinking.
Repeat the process with every blinking button and finish the
copy operation.
NOTE:
If a code of your TV remote control already exists on the 40100
Remote Control, CODE will be displayed on the screen during
the learning process.
Should you wish to learn a code on any of the device buttons,
for instance the TV button; press the TV button for at least 3
seconds. The TV button will start blinking.
Then press the start button on the TV remote control. If it has
been learnt correctly, the 40100 Remote Control screen will
display OK .
5-10 cm.
Andere Handbücher für DOMOS2
6
Inhaltsverzeichnis
Andere EGi Fernbedienung Handbücher
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
