EHP DRC 433 Bedienungsanleitung
Connections....................................................................................................................................... 10
OLED display...................................................................................................................................... 11
Input keyboard .................................................................................................................................. 12
Integrated data storage..................................................................................................................... 14
Menu ................................................................................................................................................. 16
Frequency tables ............................................................................................................................... 28
Change frequency & scale number of the crane scale...................................................................... 29
Manufacturer: EHP-Wägetechnik GmbH
Address: Dieselstrasse 8
D-77815 Bühl (Baden)
hereby declares that the product: Data Receiver Type DRC 433
with all options complies with the following harmonized standards:
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6,
EN 61000-4-11 according to Directive 2004/108/EC (electromagnetic compatibility)
EN 60950-1:2006 in accordance with Directive 2006/95/EC (Low Voltage Directive).
This product is marked with the CE mark.
Bühl, January 2022 Markus Ebel / Technical manager
This declaration has been prepared in accordance with DIN EN ISO/IEC 17050-1.
In this technical manual you will find information on the operation of the data receiver type DRC 433
►Read the operating instructions before starting up the DRC 433 data receiver. This will protect you
and prevent damage to your device.
►Always keep this manual in a place where employees, service personnel, etc. can view it.
Design features of this guide
Various elements of this guide have specified design features. This way you can easily distinguish the
following elements:
Normal text
● Enumerations
►Action steps
Table titles and figures are in bold.
Tips contain additional information.
Figure design features
If elements of a figure are referred to in a legend or in the running text, they are assigned a number
(1). The numbers in the running text always refer to the figure shown.
Figure 1 -Explanation design features
Table 1 - Technical data
● Device may only be opened by a specialist!
● Device must be protected from heat and moisture!
To avoid the risk of electric shock, do not open the remote control. There are no user-repairable
parts inside the unit. Leave repairs to qualified customer service. There is a risk of contact with non-
insulated parts inside the device, which can lead to electric shocks.
Operating environment
Avoid using this device in an insufficiently ventilated, humid or hot place.
Disposal
If you wish to dispose of this product, do not mix it with ordinary household waste. There is a
separate collection system for used electronic products through which proper treatment, recovery
and recycling is ensured in accordance with existing legislation.
In case of malfunctions
● Repairs may only be carried out by qualified personnel!
● Read through the chapter "Help in case of malfunctions" and "Error detection
● Contact EHP customer service.
The warranty is void in the event of:
•Non-intended use of the manufacturer's specifications in this operating manual
•Use outside of use
•mechanical damage, damage due to moisture and liquids
•Opening or mechanical modification
•Use of non-original EHP chargers and batteries
•Manipulation of the loading device
● Data receiver type DRC 433
The following accessories are included as standard:
•3 NiMH batteries 1.2V 2400-2850mAh
•Plug-in power supply
•Driver and Firmware CD
The driver and firmware CD contains:
•Driver for Windows 10
•Operating instructions in German and English
Figure 2- Data receiver type DRC 433
The DRC 433 is supplied with built-in AA batteries and can be used directly. Switch on the DRC 433 by
pressing and holding the "Tara | 1 | " key on the input keypad.
The battery compartment is located on the rear of the DRC 433 and can be opened by loosening the
two Phillips screws. Insert the batteries according to the installation position marked in the battery
compartment.
Battery compartment closed
Battery compartment open
Figure 3 - Battery compartment
The DRC 433 is equipped with an infrared transmitter, USB port and a charging socket on the top (1).
The OLED display (2) and the input keypad (3) are located on the front.
Figure 4 - Top side DRC 433
The infrared transmitter (1), the USB port (2) and the charging socket (3) are located on the top side.
Via the USB connection (2), weighing data can be transmitted to the PC and processed further. As long
as the DRC 433 is connected via the USB port, power is also supplied via this port.
The DRC 433 can be charged using the supplied power supply unit. Plug the power supply unit into the
socket, the internal spar plug fits into the charging socket (3) on the front of the DRC433 with reverse
polarity protection. The charging process is started automatically.
When the DRC 433 is switched on, a charging animation is shown in the display as long as the battery
is being charged. As soon as the battery is fully charged, the animation stops. The remote control can
also be charged when it is switched off.
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
