Ei Electronics B16009-R0-160RC Series Bedienungsanleitung

2. ALARM REMOVAL

SLIDE ALARM OFF BASE

WITH THE SCREWDRIVER STILL INSERTED, PUSH THE LOWER

HALF OF THE ALARM AWAY FROM THE SCREWDRIVER, IN THE

DIRECTION OF THE ARROW ON THE COVER

HOLD THE LOWER HALF OF THE ALARM AND REMOVE FROM

THE BASE PLATE BY MOVING IT VERTICALLY DOWNWARDS,

WARDS THE FL

REMOVE ALARM

LOCATE REMOVAL SLOT

LOCATE THE ARROW ON THE FRONT FACE OF THE ALARM.

THE SLOT IS LOCATED DIRECTLY ABOVE THE ARROW.

INSERT SCREWDRIVER

INSERT A FLAT-BLADED SCREWDRIVER HORIZONTALLY

APPROX. 1cm INTO THE CENTRE OF THE REMOVAL SLOT

B16009-R0-160RC SERIES-U&C 17/1/07 11:13 AM Page 1

Do not paint your alarm. Do not allow

paint, water or dust to contaminate your

alarm.

Your alarm is a mains 230V AC

electrical appliance. Do not open or

insert an

thin

into the alarm.

3. IMPORTANT INFORMATION

Regularly check that the green mains

indicator light on the cover is lit.

If alarm beeps once every 40 seconds for

over 20 minutes, the battery is probably

depleted (models Ei141/144/146 only)

and must be replaced.

(see "CHANGING

THE BATTERY" section on page 4).

Test weekly - press and hold the test

button on the alarm for 10 seconds. The

alarm will sound loudly and the red light

on the cover should flash rapidly. All the

other interconnected alarms should sound.

If a nuisance alarm occurs, press the

test/hush button to silence the alarm for

10 minutes.

Clean your alarm regularly. This will

reduce the risk of false alarms.

Remove or completely cover your alarm

when decorating to prevent dust or other

contamination dama

the unit.

If your alarm sounds for no reason and

will not reset, it can be removed by

releasing the clip on the base.

(see "ALARM REMOVAL" section on page 2).

B16009-R0-160RC SERIES-U&C 17/1/07 11:13 AM Page 2

4. CHANGING THE BATTERY

(Models Ei141 / 144 / 146 only)

1. Switch off mains power to alarm (green light on cover

should go out).

2. Remove unit as shown in “ALARM REMOVAL” section on

page 2.

3. Locate battery slot in base of alarm as shown below.

4. Unclip battery from battery snap connectors.

5. Connect new battery by clipping back on to battery snap

connectors. Use only 9V Alkaline batteries

Duracell MN1604, Energizer 522. Other batteries can

cause problems.

We recommend that the “use by date” on the battery should

still have at least 2 years to go. Older batteries will give

beeps prematurely.

6. Slide unit back on to the base. A click should be heard as

the alarm engages. (The unit cannot be replaced on the

base unless a battery is installed).

7. Press and hold the test button - horn should sound loudly.

8. Reinstate mains power to alarm (green light on cover

should come on).

We recommend that the battery is replaced at least every

three years for optimum performance.

5. TESTING & MAINTAINING YOUR ALARM

INSPECTION &TESTING PROCEDURE

Check all your alarms weekly, especially after initial

installation or after re-occupation (e.g. following a holiday):

(i) Check that the green mains indicator light is on. (If it is

off check circuit breakers, fuses and wiring etc.) Check the red

light on the cover flashes every 40 seconds.

(ii) Press the test button for up to 10 seconds to ensure the

sensor chamber, electronics and sounder are working. A red

light on the cover, will flash while horn is sounding. The alarm

B16009-R0-160RC SERIES-U&C 17/1/07 11:13 AM Page 3

will stop when the button is released. Pressing the test button

simulates the effect of smoke or heat during a real fire and is

the best way to ensure the Alarm is operating correctly.

WARNING: DO NOT TEST WITH FLAME

This can set fire to the Alarm and damage the house

We do not recommend testing with smoke or heat as the

results can be misleading unless special apparatus is used.

(iii) Check for any sign of contamination such as cobwebs or

dust and clean the alarm as described in the “CLEANING

YOUR ALARM” section on page 6, if necessary.

(iv) Interconnected Alarms only - Test the first unit by

pressing the button for 10 seconds. All the units should alarm

within 10 seconds of the first horn sounding. The red light on

the first unit only will flash about once a second. Check all the

other units similarly.

(v) Check the functioning of the mains battery back-up directly

after installation and then at least yearly as follows:

- Turn off the mains power at the distribution board and check

that the green indicator light is extinguished.

- Press the test button and ensure the horn sounds loudly for

10 seconds.

Turn on the mains supply at the distribution board only if the

unit passes the above test.

Note: If the mains is disconnected and the battery is almost

depleted the unit will beep every 40 seconds for at least 30 days.

(vi) Monitor the alarm over a short period of time for any

beeps.

5.1 If the unit is beeping

The Alarm automatically monitors the battery every 40

seconds to ensure that it is satisfactory. If it is depleted it will

give a short beep every 40 seconds.

Models Ei141, Ei144 & Ei146 only

Before replacing the battery, check that the beeps are not

due to one of the following:

(i) battery snaps not connected properly.

(ii) On the Optical Smoke Alarm only (Ei146) if the unit

beeps and the red light does not flash at the same time it

indicates a problem with the smoke chamber - see

“CLEANING YOUR ALARM” section on page 6.

(iii) If the beeps have continued for over 20 minutes (and

the other causes of beeps have been ruled out - see

“TROUBLESHOOTING” section on page 11) the battery

must be replaced.

See “CHANGING THE BATTERY” section on page 4.

B16009-R0-160RC SERIES-U&C 17/1/07 11:13 AM Page 4

Models Ei161RC, Ei164RC & Ei166RC only

(i) Check that the green mains power light is on. If it is off

the Alarm is not receiving mains power and is being

powered from its internal back-up cells. The beeps

indicate that they are depleted. The cells are not

replaceable. Re-connect the mains, check fuse, circuit

breakers and wiring. If in doubt contact a qualified

electrician. The beeps should cease within 2 hours as the

cells charge up. Fully charged, the cells will provide up to

6 months back-up without mains power.

(ii) On the Optical Smoke Alarm only (Ei166RC) if the

unit beeps and the red light does not flash at the same

time it indicates a problem with the smoke chamber - see

“CLEANING YOUR ALARM” section on page 6.

If all of the above possible causes of beeps have been

ruled out, but the beeping has still persisted for over 2

hours with the green light on - the rechargeable cells

may be defective. The Smoke / Heat Alarm must be

returned to the manufacturer for repair or replacement - see

“GETTING YOUR ALARM SERVICED” section on page 10.

Please note: The ionisation alarms (Ei141/161RC) give two

short beeps about a second apart at the end of the hush

period (i.e. about 10 minutes after test/hush button has been

pressed). These two beeps should not be confused with low

battery beeps.

A unit will operate from the mains alone, even with a fully

depleted or a defective battery (and give beeps every minute),

though it may not give sufficient warning of fire if the mains

supply is disconnected for any reason. If there are any

problems get a qualified electrician to inspect the house

wiring and connections to the alarms.

If there are still problems the unit must be returned for

examination - see “GETTING YOUR ALARM SERVICED”

section on page 10.

6. CLEANING YOUR ALARM

WARNING: Electrical shock hazard. Disconnect the AC mains

at the fuse box or circuit breaker powering the Alarm before

following the cleaning instructions.

Clean your Alarm regularly, particularly in dusty areas. Use

the narrow nozzle attachment of your vacuum cleaner to

remove dust, insects and cobwebs from the sides and cover

slots where the smoke or heat enters. To clean the cover, wipe

with a damp cloth. Dry cover thoroughly with a lint free cloth.

WARNING: Do not paint your Alarm.

Other than the cleaning described above, no other customer servicing of

this product is required. Repairs, when needed, must be performed by the

manufacturer.

All Alarms are prone to dust and insect ingress which can cause false

alarms or failure to alarm.

B16009-R0-160RC SERIES-U&C 17/1/07 11:13 AM Page 5

The latest design, materials and manufacturing techniques have been used

in the construction of our Alarms to minimize the effects of contamination.

However it is impossible to completely eliminate the effect of dust and

insect contamination, and therefore, to prolong the life of the Alarm you

must ensure that it is kept clean so that excess dust does not build up. Any

insects or cobwebs in the vicinity of the Alarm should be promptly removed.

In certain circumstances even with regular cleaning, contamination can

build up in the smoke sensing chamber causing the alarm to sound or fail.

If this happens the alarm must be returned to us for servicing or

replacement. Contamination is beyond our control, it is totally unpredictable

and is considered normal wear and tear.

For this reason, contamination is not covered by the guarantee and a

charge is made for servicing such units.

If you experience persistent false alarms, in particular locations, due to

contamination of the smoke chamber you could consider replacing Optical

Smoke Alarms (Ei146/166RC) with Ionisation Smoke Alarms

(Ei141/161RC). Ionisation type alarms are less susceptible to dust than

Optical type alarms.

7. NUISANCE ALARMS

When sure that it is just a nuisance alarm, simply press the

test/hush button briefly on the Alarm to silence the unit for 10

minutes.

If, when the alarm goes off, there is no sign of smoke, heat or

noise to indicate that there is a fire, you should get your family

into a safe place, before you start investigating.

Check the house carefully in case there is a small fire

smouldering somewhere.

Check whether there is some source of smoke or fumes, for

example cooking fumes being drawn past the Smoke Alarm

by an extractor.

If there are frequent nuisance/false alarms it may be

necessary to re-locate the device away from the source of the

fumes or replace an Ionisation Alarm with an Optical Alarm. If

for some reason the alarm continues to sound without smoke

or heat being present (due to insect infestation or

contamination build-up for example) the units can be silenced

by disconnecting the mains power and removing the unit - see

“ALARM REMOVAL” section on page 2.

If cleaning the Alarm does not correct the problem it can be

returned to the manufacturer for repair or replacement - see

“GETTING YOUR ALARM SERVICED” section on page 10.

Hush Feature

All the Smoke/Heat Alarms have a combined Test/Hush

Button to help you control nuisance false alarms.

1. To cancel a false alarm, press the Test/Hush Button located

on the cover. The Alarm will automatically switch to a reduced

sensitivity condition (very large levels of smoke from a nearby

fire will override the Hush on the Smoke Alarms). This

condition allows unwanted alarms to be silenced for a period

of approximately 10 minutes.

The unit will flash the red light every 10 seconds (instead

of the normal 40 seconds) to indicate the sensitivity is

B16009-R0-160RC SERIES-U&C 17/1/07 11:13 AM Page 6

reduced. At the end of the hush period the Ionisation

Smoke Alarms (Ei141/161RC) and the Heat Alarms

(Ei144/164RC) will give two short beeps.

On interconnected Alarms, pressing the Test/Hush Button on

the one sensing smoke (i.e. the one with the red light flashing

every second) will silence all alarms. Pressing the Hush

Button on any other Alarm will not cancel the alarm.

2. The unit will reset to normal sensitivity at the end of the

silenced period. If additional silenced time is required, simply

push the Test/Hush Button again.

8. IMPORTANT SAFEGUARDS

When using household protective devices, basic safety

precautions should always be followed, including those listed

below:

• Please read all instructions.

• Rehearse emergency escape plans so everyone at home knows

what to do in case the alarm sounds. Further information can be

obtained from the Home Office Publication or from your local fire

prevention officer.

• To maintain sensitivity to smoke, do not paint or cover the

Smoke Alarm in any manner; do not permit any

accumulation of cobwebs, dust or grease.

• If unit has been damaged in any way or does not function

properly, do not attempt a repair. Return the Alarm - see

“GETTING YOUR ALARM SERVICED” section on page 10.

• This appliance is only intended for premises having a

residential type environment.

• Smoke / Heat Alarms are not a substitute for insurance. The

supplier or manufacturer is not your insurer.

• The chamber inside the Ionisation (Ei141/161RC) Smoke

Alarms contains a small amount of radioactive material

(33kBq of Amercium 241). Do not tamper with the chamber.

You may safely install and clean the Smoke Alarm following

this leaflet’s instructions.

• Do not dispose of your Alarm in a fire.

9. PLANNING YOUR ESCAPE ROUTE

Use the Smoke / Heat Alarm Test Buttons to familiarise your

family with the Alarm sound and to practice fire drills regularly

with all family members. Draw up a floor plan that will show

each member at least 2 escape routes from each room in the

house.

Children tend to hide when they don’t know what to do. Teach

children how to escape, open windows, and use roll up fire

ladders and stools without adult help. Make sure they know

what to do if the alarm goes off - see overleaf.

B16009-R0-160RC SERIES-U&C 17/1/07 11:13 AM Page 7

1. Check room doors for heat or smoke.

Do not open a hot door. Use an

alternate escape route. Close doors

behind you as you leave.

2. If smoke is heavy, crawl out, staying

close to floor. Take short breaths, if

possible, through a wet cloth or hold

your breath. More people die from

smoke inhalation than from flames.

3. Get out as fast as you can. Do not

stop for packing. Have a prearranged

meeting place outside for all family

members. Check everybody is there.

4. Call the Fire Brigade from a

neighbour’s house. Remember to give

your name and address.

5. NEVER re-enter a burning house.

Limitations of Smoke / Heat Alarms

Smoke / Heat Alarms have significantly helped to reduce the

number of fire fatalities in countries where they are widely

installed.

However independent authorities have stated that they may

be ineffective in some circumstances. There are a number of

reasons for this:

• The Alarms will not work if the mains power is off and the battery

is depleted. On the Ei141/144/146 alarms the batteries should be

replaced every three years as a precaution or if the unit gives a

low battery beep.

• NOTE: Constant exposure to high or low temperatures or

high humidity may reduce the life of the Alkaline battery.

• Smoke / Heat Alarms will not detect fire if sufficient smoke /

heat does not reach the alarm. Smoke / heat may be

prevented from reaching the Alarm if the fire is too far away,

for example, if the fire is on another floor, behind a closed

door, in a chimney, in a wall cavity, or if the prevailing air

draughts carry the smoke / heat away. Installing Smoke /

Heat Alarms on both sides of closed doors and installing

more than one Smoke / Heat Alarm as recommended in the

‘INSTALLER INSTRUCTIONS’ booklet significantly

improves the probability of early detection.

• The Alarm may not be heard.

• A Smoke / Heat Alarm may not wake a person who has

taken drugs or alcohol.

B16009-R0-160RC SERIES-U&C 17/1/07 11:13 AM Page 8

• Smoke / Heat Alarms may not detect every type of fire to

give sufficient early warning.

• Fire Authorities recommend that both Optical and Ionisation

Smoke Alarms should be fitted for the fastest response to all

types of fires.

• Smoke / Heat Alarms don’t last indefinitely. For example if

there is a build up of contamination, performance will be

impaired.

It is recommended that the Smoke / Heat Alarms are replaced

after 10 years as a precaution.

10. ALARM CONTROL (OPTIONAL)

Models Ei161RC / 164RC / 166RC only

A System Control Switch (Ei1529RC) is available as an optional

accessory. It allows the user to perform the following functions

from a remote location:

LOCATE - If alarms sound press Locate to allow the source

of alarm to be identified.

HUSH - Press Hush to silence nuisance alarms.

TEST - Operate weekly to Test the alarms.

MAINS CHECK - Test will not work with mains absent.

11. GETTING YOUR ALARM SERVICED

If your Alarm fails to work after you have carefully read all the

instructions, checked the unit has been installed correctly, and

is receiving AC power (green light on) contact Customer

Assistance at the address given at the end of this leaflet. If it

needs to be returned for repair or replacement put it in a

padded box and send it to “Customer Assistance and

Information” at the nearest address given on the Alarm or in

this leaflet. Do not snap on to the mounting plate as this

connects the battery and the unit may beep or alarm in the

post. State the nature of the fault, where the Alarm was

purchased and the date of purchase.

12. FIVE YEAR GUARANTEE

Ei Electronics guarantees this Alarm (excluding battery in the

Ei141/144/146 models) for five years from date of purchase against

any defects that are due to faulty materials or workmanship. This

guarantee only applies to normal conditions of use and service, and

does not include damage resulting from accident, neglect, misuse,

unauthorised dismantling, or contamination howsoever caused. This

guarantee excludes incidental and consequential damage. If this

Alarm should become defective within the guarantee period, it must

be returned to Ei Electronics, with proof of purchase, carefully

packaged, with the problem clearly stated. (see “Getting Your Alarm

Serviced”) We shall at our discretion repair or replace the faulty unit.

Do not interfere with the Alarm or attempt to tamper with it. This will

invalidate the guarantee, but more importantly may expose the

user to shock or fire hazards.

This guarantee is in addition to your statutory rights as a consumer.

B16009-R0-160RC SERIES-U&C 17/1/07 11:13 AM Page 9

13. TROUBLESHOOTING

1. FREQUENT NUISANCE ALARMS OCCUR:

(1) Close kitchen / bathroom door when in use.

(2) Ensure that the alarm is sited at least 6m away from

sources of fumes.

(3) Contamination from insects, paint or paint fumes may have

occurred. Clean the alarm - see “CLEANING YOUR ALARM”

section on page 6.

(4) If the problem persists, resiting of the unit should be

considered.

2. ALARM SOUNDS FOR NO APPARENT REASON:

(1) Identify the alarm source. On interconnected units, the red

light on the cover will flash rapidly only on the unit which is the

source of the alarm. If an optional Ei1529RC Control Switch is

installed, press Locate when system is sounding to identify

source of alarm.

(2) Check for fumes, steam etc. from the kitchen or bathroom.

Paint and other fumes can cause nuisance alarms.

(3) Press the test/hush button to silence the Smoke/Heat

Alarm for 10 minutes.

(4) If alarm does not stop, switch off mains and remove unit -

see “ALARM REMOVAL” section on page 2. (Only remove

the alarm with the red light flashing, the others are probably

satisfactory).

3. LOW BATTERY & OTHER BEEPS:

(On Ei141/144/146 only)

If the battery is correctly connected and the unit has beeped

for over 20 minutes the battery is probably depleted. Obtain a

new battery, disconnect the mains, then remove the alarm

and replace the depleted battery.

(On Ei161RC/164RC/166RC only)

Check the green mains power light is on. If not, check fuse,

circuit breakers and wiring connections. If the green light is off,

the Lithium cells will deplete after some months without mains

and will need to be recharged. If turning on the mains fails to

stop the beeps, a fault may exist. Switch off mains and remove

the unit - see “ALARM REMOVAL” section on page 2.

(All Alarms)

(1) If the green mains light is on and replacing battery,

recharging Lithium cells or cleaning unit has not stopped the

The crossed out wheelie bin symbol that is on your

product indicates that this product should not be disposed

of via the normal household waste stream. Proper

disposal will prevent possible harm to the environment or

to human health. When disposing of this product please

separate it from other waste streams to ensure that it can

be recycled in an environmentally sound manner. For

more details on collection and proper disposal, please

contact your local government office or the retailer where

you purchased this product.

B16009-R0-160RC SERIES-U&C 17/1/07 11:13 AM Page 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ei Electronics Rauchmelder Handbücher

Ei Electronics

Ei Electronics Ei100TY Bedienungsanleitung

Ei Electronics

Ei Electronics Ei141 Ionisation Bedienungsanleitung

Ei Electronics

Ei Electronics Ei146 Optical Bedienungsanleitung

Ei Electronics

Ei Electronics Ei3105RF Optical Bedienungsanleitung

Ei Electronics

Ei Electronics Ei144 Heat Bedienungsanleitung

Ei Electronics

Ei Electronics Ei603 Series Bedienungsanleitung

Ei Electronics

Ei Electronics MCP401RC Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 100R Ionisation Bedienungsanleitung

Ei Electronics

Ei Electronics Ei160e Series Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 175 Ionisation Bedienungsanleitung

Ei Electronics

Ei Electronics Ei3100RF? Ei3500RF Handbuch

Ei Electronics

Ei Electronics Ei650iW Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 156TLR Optical Bedienungsanleitung

Ei Electronics

Ei Electronics Ei140RC Series Bedienungsanleitung

Ei Electronics

Ei Electronics Ei100BNX Handbuch

Ei Electronics

Ei Electronics Ei3100RF? Ei3500RF Handbuch

Ei Electronics

Ei Electronics Ei141EK Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 156TLR Optical Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 405C Handbuch

Ei Electronics

Ei Electronics Ei650 Series Bedienungsanleitung

Ei Electronics

Ei Electronics Ei161RC Ionisation Bedienungsanleitung

Ei Electronics

Ei Electronics EiA207 Series Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 3105TY Bedienungsanleitung

Ei Electronics

Ei Electronics Ei603CRF Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung

Radal Technology

Radal Technology Cig-Arrête CSA-POD Bedienungsanleitung