Ei Electronics Ei 105B Bedienungsanleitung

INSTRUCTIONS

This leaflet contains vital information on the operation and

installation of your Smoke Alarm. Please read carefully and

retain for future use. If you are just installing the unit this

leaflet MUST be given to the householder.

1. BASIC INFORMATION ABOUT YOUR

SMOKE ALARM

A Smoke Alarm is an early warning device. Installing Smoke

Alarms can give you and your family valuable extra time to

escape.

Note:-

• Install as close to the centre of the ceiling as possible.

• Press the Test Button weekly.

• Replace the battery once a year or when the Alarm beeps

once every minute and the red light flashes at the same

time.

• If the Alarm beeps without the LED flashing at the same

time the unit must be cleaned.

• A SmokeAlarm does not prevent fires.

• Plan your escape route.

• Proper protection may require more than one Smoke

Alarm.

• If you have any questions or doubts about Smoke Alarms

contact the supplier or your local Fire Brigade.

2. LOCATING SMOKE ALARMS

Sufficient smoke must enter the Smoke Alarm before it will

respond. Your Smoke Alarm needs to be within 10 paces (7.5

metres) of the fire to respond quickly. It also needs to be in a

position where its alarm can be heard throughout your home,

so it can wake you and your family in time for you all to

escape. A single SmokeAlarm will give some protection if it is

properly installed, but most homes will require two or more to

ensure that a reliable early warning is given. For maximum

protection you should put individual Smoke Alarms in all the

rooms where fire is most likely to break out (except bathroom

and kitchen).

Your first Smoke Alarm should be located between the sleep-

ing area and the most likely sources of fire (living room or

kitchen for example). But it should not be more than 10 paces

(7.5 metres) from the door to any room where a fire might start

and block your escape from the house.

Important: This Smoke Alarm is only suitable for domestic

use.

Recommended locations, Figures 1, 2, & 3

for minimum protection

•on each storey

•in each sleeping area

•every 7.5 metres of hallways & rooms

•within 3 metres of all bedroom doors

for maximum protection

in every room (except bathrooms and kitchens)

Figure 1: Single storey dwelling

Figure 2: Single storey dwelling with separate sleeping areas

Figure 3: Multi Storey Dwelling

a) Single Storey Dwelling

If the home is on one level (a bungalow or mobile home for

example) you should put the first SmokeAlarm in a corridor or

hallway between the sleeping and living areas. Place it as

near to the living area as possible, but make sure you can

hear it loudly enough to wake a person in the bedrooms. (See

Figure 1)

If your bungalow is very large and the corridor or hallway is

more than say 22 paces (15 metres) long, one Smoke Alarm

will not be sufficient. This is because no matter where it is

located it will be more than 7.5 metres from potential fires.

In houses with more than one sleeping area, Smoke Alarms

should be placed between each sleeping area and the living

area. (For example, see Figure 2)

b) Multi Storey Dwellings

If your home is on more than one level the best place for your

first Smoke Alarm is in the downstairs hallway near the stairs.

(For example, see Figure 3). This is because smoke is likely

to be detectable in the hallway before it reaches the upstairs

landing and bedrooms. Your second Smoke Alarm should be

upstairs, because the downstairs Smoke Alarm is unlikely to

detect the smoke from a fire in a bedroom upstairs. We

strongly recommend that Smoke Alarms are fitted on each

story.

c) Maximum Protection

For maximum protection you should put individual Smoke

Alarms in all the rooms where fire is most likely to break out,

(apart from kitchens, bathrooms etc., see “Locations to

Avoid”). The living room is the most likely place for a fire to

start at night, followed by the kitchen and then the dining

room. You should also consider putting Smoke Alarms in any

bedrooms where fires might occur, for instance, where there

is an electrical appliance such as an electric blanket or heater,

or where the occupant is a smoker. You could also consider

putting Smoke Alarms in any rooms where the occupant is

unable to respond very well to a fire starting in the room, such

as an elderly or sick person or a very young child.

d) Checking you Can Hear your Smoke Alarm

With the Smoke Alarm sounding in its intended location,

check you are able to hear it in each bedroom with the door

closed, above the sound of your radio. The radio should be

set to a reasonably loud conversation level. If you can’t hear

it over your radio the chances are that it wouldn’t wake a per-

son.

If a Smoke Alarm is too far away for it to wake you, it is best

to interconnect it to another Smoke Alarm near the bedroom.

A maximum of twelve Smoke Alarms may be interconnected

(See page 1 for the model numbers of Smoke Alarms with

interconnect), so that all interconnectedAlarms respond when

one Alarm senses smoke (see page 9 for further details).

3. POSITIONING YOUR SMOKE ALARM

Position your Smoke Alarm to comply with applicable building

regulations.

a) Ceiling Mounting

Hot smoke rises and spreads out, so a central ceiling position

is the preferred location. The air is “dead” and does not move

in corners, therefore Smoke Alarms must be mounted away

from corners.

Place the unit at least 0.5 m from any light fitting or decorative

object which might obstruct smoke entering the SmokeAlarm.

Keep at least 0.5 m away from walls and corners. (see Figure

Wall mounting is not recommended for Smoke Alarms.

b) Mounting on a Sloping Ceiling

In areas with sloping or peaked ceilings install your Smoke

Alarm 90 cm from the highest point measured horizontally,

because “dead air” at the apex may prevent smoke from

reaching the unit.

c) Locations to Avoid

Don’t place your Smoke Alarm in any of the following areas:

•Bathrooms, kitchens, shower rooms, garages or other

rooms where the SmokeAlarm may be triggered by steam,

condensation, normal smoke or fumes. Keep at least 6 m

away from potential sources of fumes.

•Attics or other places where extremes of temperature may

occur (below 4oC or above 40oC).

•Near a decorative object, door, light fitting, window

moulding etc., that may prevent smoke from entering the

Smoke Alarm.

•Surfaces that are normally warmer or colder than the rest

of the room (for example attic hatches, uninsulated exteri-

or walls etc). Temperature differences might stop smoke

from reaching the unit.

•Next to or directly above heaters or air conditioning

vents, windows, wall vents etc. that can change the

direction of airflow.

•In very high or awkward areas where it may be difficult to

reach the Alarm (for testing, battery replacement etc).

•Locate unit at least 1.5m and route wiring at least 1 m

away from fluorescent light fittings as electrical “noise”

and/or flickering may affect the unit.

•Locate the unit at least 1 metre from dimmer controlled

lights and wiring - some dimmers can cause interference.

•Locate away from very dusty or dirty areas as dust build-

up in the chamber can make unit too sensitive and prone

to alarm. It can also block the insect screen mesh and pre-

vent smoke from entering the smoke detector chamber.

•Do not locate in insect infested areas. Small insects get-

ting into the smoke detector chamber can cause intermit-

tent alarms.

d) Nuisance/False Alarms

If, when the Alarm goes off, there is no sign of smoke, heat or

noise to indicate that there is a fire, you should get your fam-

ily into a safe place, before you start investigating.

Check the entire house/apartment carefully in case there is a

small fire smouldering somewhere.

Check whether there is some source of smoke or fumes, for

example cooking fumes being drawn past the Smoke Alarm

by an extractor.

If there are frequent nuisance/false Alarms it may be neces-

sary to relocate the device away from the source of the fumes.

Fanning vigorously with a newspaper or similar will help

silence the Alarm by removing smoke from the sensing

chamber.

4. INSTALLING YOUR SMOKE ALARM

a) The SmokeAlarm is battery powered with no need for elec-

trical wiring (unless units are being interconnected,

see page 9).

1. Pull cover open at tab. Do not remove the base from the

back of the Smoke Alarm.

2. Find a suitable location, place the base of the SmokeAlarm

against the ceiling and mark the position of the screw holes

with a pencil.

3. Taking care to avoid any electrical wiring in the ceiling drill

two holes through the centres of the marked locations, insert

wall plugs and screw the unit into place.

b) Connecting the Battery

Using a pencil, note the date you inserted the battery on the

inside of the base for future reference. Remove the battery

from the battery holder and connect to the battery connector,

(see Figure 7).

The Ei Electronics Smoke Alarm is fitted with a battery con-

nector to make connecting the battery safer.

Check the Smoke Alarm as outlined on page 8.

c) Safety Lock

All models are fitted with a warning flag (safety interlock),

which pops up preventing the cover from being closed when

no battery is inserted. When inserting or replacing a battery

the flag must be pushed down into the battery holder.

(See Figure 7 (a)).

WARNING: Smoke Alarms do not function without a battery.

5. LOOKING AFTER YOUR SMOKE ALARM

a) Automatic Self-Test

The smoke chamber automatically tests itself every 40 sec-

onds. If the chamber is degraded the unit will beep, without

the LED flashing at the same time. If this happens clean the

unit.

b) Checking the Smoke Alarm

It is recommended that you test

your SmokeAlarm at least once a

week to be sure the unit is work-

ing properly. Press and hold the

Test Button until the Alarm

sounds (it may take up to 10 sec-

onds), (see Figure 8). It will also

help you and your family to

become familiar with the sound of

the Alarm.

c) Replacing the Battery

Fresh batteries should last about one year. When the battery

is nearly depleted and needs to be replaced the unit beeps

once a minute for at least 30 days. The alarm will stop beep-

ing when the battery has been replaced. Also replace the bat-

tery if pressing the test button does not cause the Alarm to

sound. For maximum reliability, replace the battery at least

once a year.

Insert the new battery as soon as possible to ensure proper

functioning of the unit. Leakage could cause damage to the

Alarm, furniture, and carpeting.

A flashing light every 40 seconds (without the unit beeping)

does not mean that the battery needs to be replaced.

Note: Also check proper functioning of the Smoke Alarm

after re-occupation following a holiday etc. by pressing

the test button.

PHOTO-ELECTRONIC SMOKE ALARM

FOR DOMESTIC USE

Ei 105B Ei 2105B Ei 3105B

Standard Models

Ei 105C Ei 2105C Ei 3105C

Models with Interconnect

Ei 105H Ei 2105H Ei 3105H

Models with Hush

Ei 105CH Ei 2105CH Ei 3105CH.

Models with Interconnect & Hush

123

Figure 4 Figure 5

Ideal: Centre of the ceiling

“Dead air” spaces:

Keep at least 0.5 m

away from

corners and walls.

Figure 6

9 Volt

Battery Battery Connector

Figure 7

Figure 8

Figure 7a

BEDROOM

DINING ROOM

KITCHEN

BEDROOM

BATH

ROOM

BEDROOM

LIVING ROOM

Pull open at tab

Screw hole

Test button

Siren

Label

Smoke chamber

Screw hole

BEDROOM

DINING ROOM

KITCHEN

BED

ROOM

BEDROOM

90cm

For replacement batteries, refer to the label on the smoke

chamber.

WARNING: The use of other batteries could have a detri-

mental effect on the Smoke Alarm.

d) Cleaning your Smoke Alarm

Smoke Alarms are not excessively prone to dust and insect

ingress but should still be cleaned from time to time. Use the

narrow nozzle attachment of your vacuum cleaner to remove

dust, insects and cobwebs. To clean the cover, wipe with a

damp cloth.

WARNING: Do not paint your Alarm.

Apart from the maintenance and cleaning described in this

leaflet, no other customer servicing of this product is required.

Repairs, when needed, must be performed by the manufac-

turer.

All Smoke Alarms are prone to dust and insect ingress which

can cause false alarms or failure to alarm.

In order to keep contamination to a minimum, the latest

design, up-to-date materials and methods are used in the pro-

duction of this Alarm. However, it is impossible to completely

eliminate the effect of dust and insect contamination, and

therefore, to prolong the life of theAlarm you must ensure that

it is kept clean so that excess dust does not build up. Any

insects or cobwebs in the vicinity of the Smoke Alarm should

be promptly removed.

In certain circumstances even with regular cleaning, contam-

ination can build up in the smoke sensing chamber causing

the alarm to sound or fail. If this happens the Alarm must be

returned to us for servicing or replacement. Contamination is

beyond our control, it is totally unpredictable and is consid-

ered normal wear and tear. For this reason, contamination is

not covered by the guarantee and a charge is made for serv-

icing such units.

If there are frequent nuisance/false alarms in certain locations

you should consider moving the alarm.

6. SMOKE ALARMS WITH INTERCONNECT

A maximum of twelve Smoke Alarms may be interconnected

so that all Alarms respond when one Alarm senses smoke.

( For the model numbers of Smoke Alarms with Interconnect

see page 1). This ensures that the alarms will be heard every-

where within the building.

WARNING: Do not connect EI Smoke Alarms to any

device apart from those listed on page 1 - this includes

units from other manufacturers.

A maximum of 250 m metres (820 ft) of wire can be used

(maximum resistance between detectors 50 ohms). The units

are interconnected by wiring all the terminals marked ‘1’

together, and all the terminals marked ‘2’ together as in Figure

9. Draughts from wiring openings, conduit, or mounting

boxes/holes, may blow smoke away from the sensing cham-

ber, making it insensitive. It is essential that all such openings

be closed by silicone sealant or similar.

After wiring together the Interconnect Smoke Alarms, test the

first unit by pressing the button. All alarms should sound with-

in 10 seconds. The red light should flash every second only

on the unit that is being tested. Check all the other units sim-

ilarly.

7. HUSH FEATURE

These Smoke Alarms should be interconnected only within

the confines of a single family living unit. If they are connect-

ed between different units there may be excessive nuisance

alarms. Not everybody may be aware that the Alarm is being

tested or that it is a nuisance alarm caused by cooking etc.

Some models have a hush feature (see page 1) to help you

control nuisance/false alarms.

1. To cancel a false alarm, press the test button. The alarm

will automatically switch to a reduced sensitivity condition.

This condition allows unwanted alarms to be silenced for a

period of approximately 10 minutes. The red light will flash

every 10 seconds (instead of 40 seconds) to let you know the

unit has been silenced.

2. The unit will reset to normal sensitivity at the end of the

silenced period. If additional silenced time is required, simply

push the test button again.

3. If the cause of the alarm is not clear, it should be assumed

that it is due to an actual fire and the dwelling should be evac-

uated immediately.

If kitchen or bathroom usage/layout is such that there is an

unacceptable level of nuisance alarms, re-locate the Smoke

Alarm further away where it will be less affected by cooking

fumes, steam etc.

8. IMPORTANT SAFEGUARDS

When using household protective devices, basic safety pre-

cautions should always be followed, including those listed

below:

Read all instructions carefully.

Rehearse emergency escape plans so everyone knows what

to do in case the alarm sounds.

For replacement batteries, refer to the label inside the Smoke

Alarm.

NOTE: Constant exposure to high or freezing temperatures

may reduce the life of the battery.

Do not disconnect the battery to stop alarm sounding.

(Fanning vigorously with a newspaper or similar will remove

nuisance smoke from the SmokeAlarm and stop it sounding).

Do not attempt to recharge or burn batteries, as they may

explode. Depleted batteries should be discarded properly.

When removing the battery, handle carefully to avoid possible

eye damage or skin irritation from a leaking or corroded bat-

tery.

To maintain sensitivity to smoke, do not paint or cover Smoke

Alarms in any manner; do not permit any accumulation of cob-

webs, dust or grease.

If the unit has been damaged in any way or does not function

properly, do not attempt a repair. Return Smoke Alarm to the

manufacturer (see “Getting your Smoke Alarm Serviced”,

page 14).

This appliance is intended for domestic household use only.

This is not a portable product. It must be permanently mount-

ed following the instructions.

SmokeAlarms are no substitute for insurance. The supplier or

manufacturer is not your insurer.

9. LIMITATIONS OF SMOKE ALARMS

•Smoke Alarms combined with Heat Alarms can significant-

ly reduce the number of fire fatalities.

•However, independent authorities have stated that they

may be ineffective in some circumstances. There are a

number of reasons:

•Smoke Alarms will not work if the batteries are depleted or

if they are not connected properly, or if the wrong type of

battery is used. Test regularly and replace batteries at least

yearly or when depleted.

•Alarms will only detect fire if sufficient smoke or heat

reaches the alarm’s sensors. Smoke may be prevented

from reaching theAlarm if the fire is too far away, for exam-

ple, if the fire is on another floor, behind a closed door, in

a chimney, in a wall cavity, or if the prevailing air draughts

carry the smoke away.

•Installing SmokeAlarms on both sides of closed doors and

installing more than one SmokeAlarm as recommended in

this leaflet very significantly improves the probability of

early detection.

•The Alarm may not be heard.

•A Smoke Alarm may not wake a person who has taken

drugs or alcohol.

•SmokeAlarms may not detect every type of fire to give suf-

ficient early warning. They are particularly ineffective with:

fires caused by smoking in bed, escaping gas, violent

explosions. poor storage of flammable rags and/or liquids,

(for example petrol, paint, spirits etc), overloaded electrical

circuits, arson, children playing with matches, for example.

•Smoke Alarms do not last indefinitely.

The manufacturer recommends a regular weekly check and

replacement of the unit after 10 years as a precaution.

9. PLANNING YOUR ESCAPE FOR WHEN

THE ALARM GOES

Use the Alarm test button to familiarise your family with the

Alarm sound and to practice fire drills regularly with all family

members to rehearse evacuating the building as fast as pos-

sible. Draw up a floor plan that will show each member at

least 2 escape routes from each room in the house. Children

tend to hide when they don’t know what to do. Teach children

how to escape, open windows, and use roll up fire ladders

and stools without adult help. Make sure they know what to do

if the Alarm goes off.

1. Check room doors for heat or

smoke. Do not open a hot door.

Use an alternate escape route.

Close doors behind you as you

leave.

2. If smoke is heavy, crawl out,

staying close to floor. Take short

breaths, if possible, through a wet

cloth or hold your breath. More

people die from smoke inhalation

than from flames.

3. Get out as fast as you can. Do

not stop for packing. Have a pre-

arranged meeting place outside for

all family members. Check

everybody is there.

4. Call the Fire Brigade from a

neighbour’s house. Remember to

give your name and address.

5. NEVER re-enter a burning

house.

FIRE SAFETY HINTS

Store petrol and other flammable materials in proper contain-

ers. Discard oily or flammable rags.

Always use a metal fireplace screen and have chimneys

cleaned regularly. Replace worn or damaged sockets, switch-

es, home wiring, and cracked or frayed electrical cords and

plugs.

Do not overload electrical circuits.

Keep matches and lighters away from children.

Never smoke in bed. In rooms where you do smoke, always

check under cushions for smouldering cigarettes and ashes.

Service central heating systems regularly.

Be sure all electrical appliances and tools have a recognised

approval label.

Contact the local authorities or the Fire Brigade for further

information.

10. GETTING YOUR SMOKE ALARM

SERVICED

If your SmokeAlarm fails to work after you have read the sec-

tions on “Connecting the Battery” and “Looking after your

Smoke Alarm” contact Customer Assistance at the nearest

address given at the end of this leaflet. You can also return

the unit to the manufacturer (see below for addresses). State

the nature of the fault, where the Smoke Alarm was pur-

chased and include proof of purchase.

11. GUARANTEE (LIMITED)

Ei Electronics guarantees this product against any defects

that are due to faulty material or workmanship for a five year

period (battery not included) from date of purchase. (EI

Electronics guarantees the products EI 2105B, 2105C,

2105H and 2105CH for two years only). This guarantee only

applies to normal conditions of use and service, and does not

include damage resulting from accident, neglect, misuse,

unauthorised dismantling, or contamination howsoever

caused. If this product has become defective it must be

returned to EI Electronics (see “Getting Your Smoke Alarm

Serviced”) with proof of purchase. If the product has become

defective during the guarantee period the manufacturer will

repair or replace the unit without charge. This guarantee

excludes incidental and consequential damage.

Do not interfere with the product or attempt to tamper with it.

This will invalidate the guarantee. This guarantee is in

addition to your statutory rights.

Ei Electronics,

Shannon,

Co. Clare,

Ireland

Ei Electronics,

Konigsallee 60F,

40212 Düsseldorf,

Germany

E-mail: [email protected]

www.eielectronics.com

P/N. B14331-A

910

Smoke Alarms with Interconnect

11 12

13 14 15 16

Figure 9

Dieses Handbuch passt für folgende Modelle

Andere Ei Electronics Rauchmelder Handbücher

Ei Electronics

Ei Electronics Ei 105C Optical Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 405C Handbuch

Ei Electronics

Ei Electronics Ei154TL Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 100TYC Ionisation Bedienungsanleitung

Ei Electronics

Ei Electronics Ei161RC Ionisation Bedienungsanleitung

Ei Electronics

Ei Electronics Ei605 Series Bedienungsanleitung

Ei Electronics

Ei Electronics Ei160 Handbuch

Ei Electronics

Ei Electronics RadioLINK Ei170RF Bedienungsanleitung

Ei Electronics

Ei Electronics BROOKS EIB160e Series Bedienungsanleitung

Ei Electronics

Ei Electronics Ei160e Series Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 100B Ionisation Bedienungsanleitung

Ei Electronics

Ei Electronics Ei3105RF Optical Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 181 Ionisation Bedienungsanleitung

Ei Electronics

Ei Electronics Ei603MRF Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 105C Optical Handbuch

Ei Electronics

Ei Electronics EI 100S Silencer Bedienungsanleitung

Ei Electronics

Ei Electronics EI 100C Interconnect Bedienungsanleitung

Ei Electronics

Ei Electronics Ei3024 Bedienungsanleitung

Ei Electronics

Ei Electronics EiA600 Series Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 100R Ionisation Bedienungsanleitung

Ei Electronics

Ei Electronics EiA605MRF Bedienungsanleitung

Ei Electronics

Ei Electronics Ei151TL Bedienungsanleitung

Ei Electronics

Ei Electronics aico Ei146e Bedienungsanleitung

Ei Electronics

Ei Electronics Ei146 Optical Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung

Radal Technology

Radal Technology Cig-Arrête CSA-POD Bedienungsanleitung