Ei Electronics Ei146 Optical Bedienungsanleitung

Shannon Free Zone, Shannon, Co. Clare, Ireland.

Ph.+353 61 471277 Fx.+353 61 471053

Web: www.eielectronics.com

E & OE As our policy is one of continuous product development, we reserve the right to alter product details without prior notice. Ei146 DataSht RevB

Model Ei146 Optical

Easi-Fit base

9V Alkaline Battery back up

High performance optical chamber with integral

insect screen

Test/Hush button

Advanced suppression and calibration technology

Interconnectable to other Ei mains powered alarms

Built in auto self test feature

Low power cell warning

Kitemarked to BS EN 14604:2005

5 year guarantee

Product Description

The Ei146 is an Optical Smoke Alarm that runs on 230V

AC mains power, and has a 9V alkaline battery back up

in the event of mains failure. The 9V battery will last for

up to 4 years in standby mode, and capable of powering

the smoke detector for up to 2 years in the event of

mains failure.

The Ei146 is supplied with the Easi-Fit base that allows

very quick and simple installation of the smoke alarm,

combined with simple detector head removal and

replacement. The Easi-Fit base automatically connects

both mains power and battery as the detector head

slides on to the Easi-Fit base.

The Ei146 has other advanced features such as high

performance optical chambers fitted with integral insect

screens to reduce the chances of false alarms, as well

as the ability to interconnect up to twelve alarms to allow

all alarms to sound if just one of the interconnected

alarms should be triggered.

The Ei146 has built in circuitry to aid suppression of

voltage transients and RF interference to further reduce

the chances of false alarms under such conditions.

Operation

The green indicator will illuminate to show mains

power is present

The red indicator will flash every 40 seconds to

show that the detector has performed an automatic

self test

The red indicator will flash rapidly to show an alarm

condition for the smoke detector

The “Test/Hush” button will either silence false

alarms or perform a unit self test

In “Test” mode the alarm will perform a self test and

sound the horn

In “Hush” mode the alarm enters a ten minute period

of reduced sensitivity to overcome false alarm

conditions, and will then automatically reset itself

When interconnected to other Ei mains powered

alarms, an alarm on one detector will trigger all other

interconnected alarms within one second (only the

triggered alarm will flash a red indicator)

The smoke detector will emit a beep and flash the

red light every 40 seconds to indicate that the

battery back up is depleted and needs replacing

MAINS POWERED 230V~

9V Alkaline Battery Back-Up

Shannon Free Zone, Shannon, Co. Clare, Ireland.

Ph.+353 61 471277 Fx.+353 61 471053

Email. [email protected]

Web: www.eielectronics.com

E & OE As our policy is one of continuous product development, we reserve the right to alter product details without prior notice. Ei146 DataSht RevB

Model Ei146 Optical

Installation & Placement

Wiring for Interconnected Alarms

Be very careful about correctly wiring the alarms as mixing Live and Neutral

will blow/damage interconnected alarms.

Alarms should be placed in accordance with the general guidelines shown in

the diagram above. These recommendations are based on the problem of

areas of “dead air” close to corners of rooms and apexes of ceilings, which

could result in the prevention of smoke reaching the smoke detector

Please consult instruction booklet for specific installation details

Important Precaution:

Do not install the actual smoke/heat alarm

itself in new or renovated buildings until all

work is completed (including floor coverings)

and the building has been fully cleaned. The

wiring can be installed when appropriate.

(Excessive dust and debris from building work

can contaminate the smoke chamber and

cause problems, and it will also invalidate the

guarantee). If it must be installed, cover it

completely, particularly around the edges, with

a dust cover (eg. a plastic bag), until all

cleaning is finished.. Connect wires to the unit

as in wiring diagram. All wiring must comply

with local codes.

Technical Specification

Sensor Optical, uses light scatter from

smoke

Sensitivity: Complies with BS 5446 Part 1:

2000

Source: Contains no radioactive material

Airspeed: Essentially immune to the effect

of airspeed.

Button Test: Simulates the effect of smoke and

checks chamber, electronics and

horn.

Ambient Light: Chamber housing design and

compensation overcomes

problems with stray light.

AutomaticSelf-Test: Smoke Chamber is tested every 40

Sec. and unit beeps (without LED

flash) if it is degraded.

Insect Screen: Prevents insects or debris entering

chamber (1.00mm mesh size)

Supply Voltage: 230V AC

Battery back up: 9V Alkaline Battery

Specifications are subject to change

Power-On Indicator: Continuous green LED

Alarm: Electronic Piezoelectric horn

Alarm Sound Output: 85dB (minimum) at 3m

Alarm Status: Red LED flashes every second on

unit sensing fire

Temperature Range: 0° to 40°C

Humidity Range: 15% to 95% Relative Humidity

Interconnect: Up to 12 interconnected mains

powered easi-fit smoke or heat

alarms, along with an EI128 relay

base

Fixing: Easi-Fit mounting base

Plastic material: UL94VO flame retardant

Dimensions: 152mm x 50mm depth

Weight: 345g

Warranty: 5 year (limited) warranty

Approvals: Kitemarked to BS EN 14604:2005,

CE Approved

Andere Handbücher für Ei146 Optical

Inhaltsverzeichnis

Andere Ei Electronics Rauchmelder Handbücher

Ei Electronics

Ei Electronics Ei 100R Ionisation Bedienungsanleitung

Ei Electronics

Ei Electronics Ei405TY RF Optical Bedienungsanleitung

Ei Electronics

Ei Electronics Ei146 Optical Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 105B Bedienungsanleitung

Ei Electronics

Ei Electronics EiA605MRF Bedienungsanleitung

Ei Electronics

Ei Electronics EI129 Bedienungsanleitung

Ei Electronics

Ei Electronics Ei144 Heat Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 151TLR Ionisation Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 3105TYCH Optical Bedienungsanleitung

Ei Electronics

Ei Electronics Ei151TL Montageanleitung

Ei Electronics

Ei Electronics EIB650i Series Bedienungsanleitung

Ei Electronics

Ei Electronics Ei603 Series Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 156TLR Optical Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 105C Optical Handbuch

Ei Electronics

Ei Electronics Ei160e Series Bedienungsanleitung

Ei Electronics

Ei Electronics EI 100B Standard Handbuch

Ei Electronics

Ei Electronics Ei650 Series Bedienungsanleitung

Ei Electronics

Ei Electronics Ei3100RF? Ei3500RF Handbuch

Ei Electronics

Ei Electronics RadioLINK Ei 405TY Handbuch

Ei Electronics

Ei Electronics Ei2110e Series Bedienungsanleitung

Ei Electronics

Ei Electronics Ei 184 Bedienungsanleitung

Ei Electronics

Ei Electronics Ei141 Ionisation Bedienungsanleitung

Ei Electronics

Ei Electronics Ei141EK Bedienungsanleitung

Ei Electronics

Ei Electronics EiA600 Series Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

BRK electronic

BRK electronic First Alert P1010 Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Safetec

Safetec SDS-2/6 Betriebsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung