Eiki EIP-WSS3100 Bedienungsanleitung
Quick Start Guide
MODEL EIP-WSS3100
Use this book as a start guide when setting up the projector.
For detailed information about installation, setup and operation of projector,
refer to the owner's manual on the CD-ROM.
Read the safety instructions in this quick start guide before using projector.
EIP-WSS3100
Quick Start Guide
MODEL EIP-WSS3100
Use this book as a start guide when setting up the projector.
For detailed information about installation, setup and operation of projector,
refer to the owner's manual on the CD-ROM.
Read the safety instructions in this quick start guide before using projector.
Package Overview
AC Power Cord
Unpack and inspect the box contents to ensure all parts listed below are in
the box. If something is missing, please contact your dealer.
Documentation:
Owner’s Manual (CD)y
Quick Start Guidey
BatteryProjector Remote Control
VGA Cable
45.8UR01G001 A
IR29033TR2-LAYOUT-121128
CLA-IR29033TR2-NAP-121121
ModelNo:
IR290 33
30mA
CR2025
3V
Elevator Feet
Adjusting the Projector’s Focus
Focus Ring
To focus the image, rotate the focus ring until the image is clear.
Adjusting
Adjusting the Projector’s Height
The projector is equipped with elevator feet for adjusting the image height.
To raise the image:y
Use screw in feet to raise the image to the desired height angle and ne-tune
the display angle.
To lower the image:y
Use screw in feet to lower the image to the desired height angle and ne-tune
the display angle.
The adjustment range of the elevator feet is 0 to 5.9 degrees.y
12
Elevator Feet
Elevator Feet Spacer
Adjusting
Powering On the Projector
Securely connect the power cord and signal cable. When connected, the Power1.
LED will turn red.
Turn on the lamp by pressing2. “ ” button on the control panel or on the remote
control. The Power LED will turn blue.
Turn on your source that you want to display on the screen (computer, note-3.
book, video player, etc). The projector will detect the source automatically and
will display on the screen.
If you connected multiple sources at the same time, press the “Source” button4.
on the remote control to switch between inputs.
MENU
POWER TEMP LAMP
RESYNC SOURCE
or
Powering Off the Projector
1. Press the “ ”button on the control panel or on the remote control to turn off
the projector. The following message will be displayed on the screen.
Press the “ ” button again to conrm.
Power Off?
Press power key again.
2. The Power LED will turn red and blink rapidly after the projector is turned off.
And the fans will continue to operate for about 90 seconds to ensure that the
system cools properly.
3. Once the system has nished cooling, the Power LED will stop blinking and turn
solid red to indicate standby mode.
4. It is now safe to unplug the power cord.
Adjusting Projection Image Size
Remote Control Battery Installation
Refer to the graphics and table show as below to determine the screen size and
projection distance.
Adjusting the vertical image positiony
Projection Distance (A)
Projection Distance
(B)
Screen
0-3.5 degree is the suitable angle to
correct keystone image.
WXGA Series
Screen Size (16:10) Projection Distance (A) Projection Distance (B) Projection Distance (C)
Diagonal (inch) mm Inch mm Inch mm Inch mm
70 1778 20.4 517 7.2 182 6.0 153
80 2032 23.5 596 10.3 262 7.4 187
87.2 2215 25.8 655 12.6 320 8.3 210
90 2286 26.7 677 13.5 343 8.6 219
100 2540 29.9 759 16.7 424 9.9 252
Projection Distance A(mm)=Screen size(mm) x 0.296, Tolerance is around 3.1%
Ex: Projection Distance (655mm)=Screen size(2215mm) x 0.296
This table is for user’s reference only.
Note
Note
Projection Distance (C)
Adjusting
Press rmly and slide 2.
the battery cover off.
Put the cover4.
back.
Install new battery into the3.
compartment.
Remove the old battery
and install new one
(CR2025). Ensure that
the side with a “+” is
facing up.
M
n
O
2
-
L
i
C
E
L
L
3
V
O
L
T
S
J
A
P
A
N
H
CR2025
3
V
O
L
T
S
CR2025
M
3
V
O
L
T
S
CR2025
3
V
O
L
T
S
CR2025
Before using the remote1.
control for the rst time,
remove the transparent
insulation tape.
0° to 3.5°
Connecting to Computer/Notebook
Power Cord1.
Audio Cable2.
VGA to DVI-A Cable 3.
VGA Cable4.
RS232 Cable5.
HDMI Cable6.
USB Cable7.
12V DC Jack8.
Network Cable9.
LAN
Notebook
Computer
Power socket
1
22
2
4
4
Monitor
Audio Output
+12V Output
3 4 5 6 7 8
9
Connecting to Video Sources
Power Cord1.
Microphone Cable2.
Audio Cable Jack/RCA3.
S-Video Cable 4.
Audio Cable5.
VGA to HDTV (RCA) Cable6.
HDMI Cable7.
12V DC Jack8.
Composite Video Cable9.
LAN
DVD player, Set-top box,
HDTV receiver
S-Video output
Video output
1
6
2
+12V Output
Power socket
Audio Output
DVD player, Set-top box,
HDTV receiver
5
3 4 5 6
7 8
593
Andere Handbücher für EIP-WSS3100
3
Inhaltsverzeichnis
Sprachen:
Andere Eiki Projektor Handbücher
Eiki
Eiki LC-X1 Bedienungsanleitung
Eiki
Eiki LC-X70 Einrichtungshandbuch
Eiki
Eiki EK-500U Bedienungsanleitung
Eiki
Eiki LC-XBS500 Bedienungsanleitung
Eiki
Eiki LC-XB200A Bedienungsanleitung
Eiki
Eiki LC-4300U Einrichtungshandbuch
Eiki
Eiki LC-6000U Einrichtungshandbuch
Eiki
Eiki LC-XB31 Bedienungsanleitung
Eiki
Eiki EIP-WX5000 Bedienungsanleitung
Eiki
Eiki LC-XB43 Bedienungsanleitung
Eiki
Eiki EIP-3000NA Bedienungsanleitung
Eiki
Eiki LC-XB21 Bedienungsanleitung
Eiki
Eiki LC-XT3 Einrichtungshandbuch
Eiki
Eiki LC-XB42N Bedienungsanleitung
Eiki
Eiki EIP-HDT30 Bedienungsanleitung
Eiki
Eiki EIP-WSS3100 Bedienungsanleitung
Eiki
Eiki LC-XL200 Bedienungsanleitung
Eiki
Eiki LC-W5 Bedienungsanleitung
Eiki
Eiki LC-XL200 Bedienungsanleitung
Eiki
Eiki LC-4200 Bedienungsanleitung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
Christie
Christie LHD700 Bedienungsanleitung
