Eiki LC-XBS500 Bedienungsanleitung

Quick Start Guide

MODEL

Use this book as a start guide when setting up the projector.

For detailed information about installation, setup and operation of projector,

refer to the owner's manual on the CD-ROM.

Read the safety instructions in this quick start guide before using projector.

LC-XBS500

LC-WBS500

Quick Start Guide

MODEL

Use this book as a start guide when setting up the projector.

For detailed information about installation, setup and operation of projector,

refer to the owner's manual on the CD-ROM.

Read the safety instructions in this quick start guide before using projector.

LC-XBS500

LC-WBS500

Package Overview

Unpack and inspect the box contents to ensure all parts listed below are in

the box. If something is missing, please contact your dealer.

Owner's Manual(CD) AC Power cord Remote Control with batteries

(AA or LR6)

VGA cable Quick Start Guide Lens Protection Ring

Install remote control batteries

Operating range

Wired Remote Control Transmitter

①Open the battery cover. ②Install new batteries. ③Put the cover back.

Two AA batteries

For correct polarity

(+ and –), be sure

battery terminals

are in contact

with pins in the

compartment.

Point the remote control toward the remote

control receivers on the projector (front and

back) when pressing any button.

The maximum operating range for the remote

control is about 5 meters and 60 degrees.

The remote control can be used as a wired

remote control. Wired remote control helps you

use the remote control outside of the operation

range (26.25'/8m). Connect the remote control

and the projector with the remote control cable.

Connected with the remote control cable, the

remote control does not emit wireless signal.

To ensure safe operation, please observe the following precautions:

● Use two (2) AA or LR6 type alkaline batteries.

● Always replace batteries in sets.

● Do not use a new battery with a used battery.

● Avoid contact with water or liquid matter.

● Do not expose the remote control to moisture or heat.

● Do not drop the remote control.

● If the battery has leaked in the remote control, carefully wipe the case clean and

install new batteries.

● Risk of explosion if two batteries are replaced by an incorrect type.

● Dispose of used batteries according to the instructions on the battery or local

regulations or guides.

30°

Adjusting

Positioning the projector

Note:

● The brightness in a room has a great inuence on image quality. It is recommended to limit the

ambient lighting in order to get the best image.

● All measurements are approximate and may vary from the actual sizes.

Note:

The data in "()" is the project distance for

16:9 aspect ratio.

Note:

The data in "()" is the project distance for

16:9 aspect ratio.

16:9 :

4:3 :

16:10 :

Screen size

(WxH)mm

4:3 aspect ratio

30" 100" 150" 200" 300"

610x457 2032x1524

3048x2286

4064x3048 6096x4572

Maximum 0.882m 3.034m 4.570m 6.107m 9.180m

Minimum 1.482m 5.031m 7.566m 10.101m 15.171m

Screen size

(WxH)mm

16:9 aspect ratio

30" 100" 150" 200" 300"

664x373 2213x1245

3320x1867

4427x2490 6641x3735

Maximum 1.111m 3.796m 5.713m 7.631m 11.466m

Minimum 1.859m 6.288m 9.452m 12.616m 18.943m

Screen size

(WxH)mm

16:10 aspect

ratio

30" 100" 150" 200" 300"

646x404 2154x1346

3231x2019

4308x2692 6462x4039

Maximum 0.938m 3.219m 4.848m 6.477m 9.735m

Minimum 1.573m 5.336m 8.023m 10.711m 16.086m

Adjustable feet

The projection angle can be adjusted up to 40

mm with the adjustable feet.

Rotate the adjustable feet to lift the projector

to a certain height. During lifting, rotate the two

feet clockwise.

To lower or retract the adjustable feet, rotate

the two feet counterclockwise.

Keystone distortion of projected images can

be corrected by auto settings, remote control

operation or menu operation. Adjustable feet

Screen size

(WxH)mm

16:9 aspect ratio

30" 100" 150" 200" 300"

664x373 2213x1245

3320x1867

4427x2490 6641x3735

Maximum 1.111m 3.796m 5.713m 7.631m 11.466m

Minimum 1.859m 6.288m 9.452m 12.616m 18.943m

LC-WBS500:

LC-XBS500:

30”

(Diagonal:Inch)

Max. Min.

(Center)

(Diagonal:Inch)

Max. Min.

(Center)

0.882m(1.111m)

3.034m(3.796m)

4.570m(5.713m)

6.107m(7.631m)

9.180m(11.466m)

15.171m(18.943m)

0.938 m(1.111m)

3.219m(3.796m)

4.848m(5.713m)

6.477 m(7.631m)

9.735 m(11.466m)

16.086m(18.943m)

30”

(Diagonal:Inch)

Max. Min.

(Center)

(Diagonal:Inch)

Max. Min.

(Center)

0.882m(1.111m)

3.034m(3.796m)

4.570m(5.713m)

6.107m(7.631m)

9.180m(11.466m)

15.171m(18.943m)

0.938 m(1.111m)

3.219m(3.796m)

4.848m(5.713m)

6.477 m(7.631m)

9.735 m(11.466m)

16.086m(18.943m)

Adjusting

Lens shift adjustment

Projection lens can be moved from side to side and up to down.

This function makes the positioning of images easy on the screen.

The display position can be shifted upward up

to 40%(XGA), 50%(WXGA) elevation of the

display.

The display position can be shifted to the left

up to 10% width of the display.

The display position can be shifted to the right

up to 10% width of the display.

When the lens is shifted to top.

When the lens is shifted to leftmost. When the lens is shifted to rightmost.

When the lens is shifted to bottom.

The display position can be shifted downward

up to 40%(XGA), 50%(WXGA) elevation of the

display.

When the lens is

shifted to the center. Shifting range

a: 40% (LC-XBS500)

50% (LC-WBS500)

b: 10% (LC-XBS500)

10% (LC-WBS500)

Adjusting

Connecting the AC power cord

This projector uses nominal input voltages of

100–240V AC and it automatically applies to

different input voltages. It is designed to work

with a single-phase power system having a

grounded neutral conductor.

To reduce the risk of electrical shock, do not

plug into any other type of power system. If

you are not sure of the type of power being

supplied, consult your authorized dealer or

service station. Connect the projector with all

peripheral equipment before turning it on.

The AC outlet should be near this equipment

and must be easily accessible.

Note:

Note:

For safety, unplug the AC power cord when the projector is not in use. When the projector is

connected to an outlet with AC power cord, it is in stand-by mode and consumes a little electric

power.

Connect the AC power cord

(supplied) to the projector.

Turn on the projector

1.Complete peripheral connections (with a

computer, HDR,etc.) before turning on the

projector.

2. Connect the projector’s AC power cord into

AC outlet.The POWER indicator turns red.

3. Press the POWER button on side control or

on the remote control. The POWER indicator

becomes green and the cooling fans start to

work. The preparation display appears on

the screen and the countdown starts.

4. If the projector is locked with a PIN code, a

PIN code input dialog box appears. Enter

the PIN code as instructed below.

Note:

● When the logo select is set to be "Off" the

logo will not be displayed on the screen.

● When the Display function is set to be "Off" ,

the logo and countdown will not be displayed

on the screen.

● During the countdown period, all operations

are invalid except shutdown.

Start-up display

Connecting

Connecting to computer(Digital and analog RGB)

Unplug the power cords of both the projector and external equipment from the AC outlet

before connecting the cables.

Cables used for connection:

● VGA cable ● Serial cable*

● HDMI cable*

(*=Cables are not supplied with the projector)

VGA IN 1 / YCbCr / S-VIDEO IN

RS-232C

VGA IN 2 / VGA OUT

HDMI

LAN

AUDIO IN

(MONO)

VIDEO IN

R L

USB-B USB-A

AUDIO OUT AUDIO INR/C

HDMI output

HDMI

cable

HDMI input

RS232 input

RS232 output

Serial

cable

(Cross)

VGA output VGA input/output

VGA

cable VGA

cable

VGA input VGA output/input

Andere Handbücher für LC-XBS500

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Eiki Projektor Handbücher

Eiki

Eiki XGA Brilliant LC-XB100 Bedienungsanleitung

Eiki

Eiki EIP-3000NA Bedienungsanleitung

Eiki

Eiki LC-NB2U Bedienungsanleitung

Eiki

Eiki EIP-X5500 Bedienungsanleitung

Eiki

Eiki LC-XB31 Bedienungsanleitung

Eiki

Eiki LC-XGA980E Einrichtungshandbuch

Eiki

Eiki 3850A Bedienungsanleitung

Eiki

Eiki LC-X800 Bedienungsanleitung

Eiki

Eiki EK-308U Bedienungsanleitung

Eiki

Eiki LC-X71 Bedienungsanleitung

Eiki

Eiki LC-WUL100AL Bedienungsanleitung

Eiki

Eiki EIP-1000T Bedienungsanleitung

Eiki

Eiki LC-120 Einrichtungshandbuch

Eiki

Eiki EK-700LU Bedienungsanleitung

Eiki

Eiki LC-XB250A Bedienungsanleitung

Eiki

Eiki LC-SM1 Bedienungsanleitung

Eiki

Eiki LC-XNB3 Bedienungsanleitung

Eiki

Eiki Projector Bedienungsanleitung

Eiki

Eiki LC NB2UW LC-NB2UW LC-NB2UW Bedienungsanleitung

Eiki

Eiki 3860A Bedienungsanleitung

Eiki

Eiki LC-SX6 Bedienungsanleitung

Eiki

Eiki LC-WXL200 Bedienungsanleitung

Eiki

Eiki LC-XB42 Bedienungsanleitung

Eiki

Eiki LC-X5 Einrichtungshandbuch

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung