Eizo CuratOR EX3140 Bedienungsanleitung

Important

Please read this “Installation Manual”, and “Instructions for Use”

(separate volume) carefully to familiarize yourself with safe and

effective usage.

Refer to the “Instructions for Use” for information on the installation /

connection of the monitor.

Color LCD Monitor

Installation Manual

This product has been adjusted specically for use in the region to which it was originally shipped. If

operated outside this region, the product may not perform as stated in the specications.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by

any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.

EIZO Corporation is under no obligation to hold any submitted material or information condential unless

prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every

effort has been made to ensure that this manual provides up-to-date information, please note that EIZO

monitor specications are subject to change without notice.

CONTENTS

CONTENTS............................................................. 3

Chapter 1 Basic Adjustment / Setting.............. 4

1-1. Loading the Monitor Settings...................... 4

1-2. Switching Input Signals ............................... 5

1-3. Using Function Buttons ............................... 5

Chapter 2 Advanced Adjustment / Setting ...... 6

2-1. Operation via the Main Menu....................... 6

2-2. Individual Functions of Main Menu............. 7

●Video Cong.................................................... 7

●System Cong................................................. 8

●Window Cong...............................................10

●PRESET.........................................................11

●Control............................................................11

Chapter 3 Troubleshooting.............................. 13

3-1. No Picture Displayed ...................................13

3-2. Imaging Problems........................................14

3-3. Other Problems............................................14

Chapter 4 Reference ........................................ 15

4-1. Main Default Settings ..................................15

4-2. PinSpecications........................................16

Appendix.............................................................. 17

LIMITED WARRANTY..............................................17

Trademark ................................................................18

License .....................................................................18

Recycling Information ............................................19

4Chapter 1 Basic Adjustment / Setting

Chapter 1 Basic Adjustment / Setting

This chapter describes the basic functions that can be adjusted and set by pressing the buttons on the front

of the monitor.

1-1. Loading the Monitor Settings

It is possible to switch to PRESET, FACTORY, or the USER settings that have been set in advance.

PRESET Basic settings are made in advance at the factory. The settings of PRESET cannot be

changed.

FACTORY Returns to settings when shipped from the factory.

USER Various settings including menus can be made for personal use. For details, see “PRESET”

(page 11).

1. Press (PRESET).

The preset menu is displayed.

Press to select the PRESET number, FACTORY, or USER number to

load, and then press (ENTER).

The pre-made settings are loaded and the settings are changed. The selectable settings are as

follows.

• PRESET1 to PRESET5

• FACTORY

• USER1 to USER10

Note

• The “PRESET” menu will disappear after ve seconds have elapsed if no operation is performed.

• is displayed for the USER number that has already been registered.

• When selecting a USER number that has not yet been registered, “No Data” is displayed.

• For information about the main default settings, see “4-1. Main Default Settings” (page 15).

Chapter 1 Basic Adjustment / Setting

1-2. Switching Input Signals

Select the signal input to the monitor and display it on the screen.

1. Press (INPUT).

The “Input Select” menu appears.

Press to select an input signal.

This switches to the selected input signal.

Press (INPUT).

The menu screen exits.

Note

• When selecting SDI, SDI 1 to SDI 4 can be selected using the buttons.

• If you press (INPUT) while the “Input Select” menu is displayed in dual screen mode, the “Input Select” menu

of the subscreen is displayed.

• The Input Select menu will display for 7 seconds without input before it disappears.

1-3. Using Function Buttons

Execute the functions assigned to the function buttons (F1 ( ), F2 ( ), F3 ( ), F4 ( ) and F5

( )). For information on how to set a function to each button, see

“Function” (page 8)

1. Press F1 ( ), F2 ( ), F3 ( ), F4 ( ) or F5 ( ).

When the function menu is displayed, the function associated with the button that is pressed will run.

Note

• In dual screen mode, press (INPUT) to select a screen for performing the target function.

• When the function button for a function that cannot be run is pressed, the message “Invalid Function” will appear.

• When the function button that has not yet been dened is pressed, the message “Undened” will appear.

6Chapter 2 Advanced Adjustment / Setting

Chapter 2 Advanced Adjustment / Setting

This chapter describes advanced monitor adjustment and setting procedures using the main menu.

2-1. Operation via the Main Menu

1. Menu display

1. Press (MENU).

The main menu is displayed.

2. Press to select the desired item, and then press .

Adjusting / setting

1. Press to select the desired item.

2. Press to set.

If “Next Menu” is displayed for items, press , and a next menu is displayed.

Exiting

1. If you repeatedly press (MENU), the menu screen exits.

Chapter 2 Advanced Adjustment / Setting

2-2. Individual Functions of Main Menu

●VideoCong

Adjustments / settings for image display.

Function Setting

range Description

Color 0 to 100 Adjusts color depth of the image.

Tint 0 to 100 Adjusts skin tones.

Brightness 0 to 100 Adjusts image darkness (black).

Picture 0 to 100 Adjusts image intensity.

S.R.S.C 0 to 20 This adjusts picture crispness.

Gamma 1.8 to 2.6

DICOM

HLG

Adjusts brightness.

Backlight 0 to 100 Adjusts brightness of backlight. In case of multiple windows,

select the main screen. The setting cannot be changed

when a screen other than the main screen is selected.

Color Temp 6500 K

9300 K

Off

Switches tone of the image.

R Gain 0 to 100 Adjusts the brightness of red in bright portions.

G Gain 0 to 100 Adjusts the brightness of green in bright portions.

B Gain 0 to 100 Adjusts the brightness of blue in bright portions.

R Bias 0 to 100 Adjusts the brightness of red in dark portions.

G Bias 0 to 100 Adjusts the brightness of green in dark portions.

B Bias 0 to 100 Adjusts the brightness of blue in dark portions.

Color Gamut sRGB

Native

BT2020

Sets the Color Gamut.

Input Color Format RGB

YUV422

YUV444

When there is a DisplayPort input, this sets the color format.

Input Range 0 to 255

16 to 235

16 to 255

Changes the dynamic range depending on the input signal.

• “0 to 255”

Use this setting when connecting PC format source.

• “16 to 235”

Set when connected to a video format device or PC

format device.

• “16 to 255”

Set when connected to a video format device or PC

format device.

Noise Reduction Off

Light

Middle

Heavy

Select Noise Reduction level for picture.

8Chapter 2 Advanced Adjustment / Setting

●SystemCong

Settings for devices.

Function Setting range Description

SDI 4K Auto

SQUARE

INTERLEAVE

Sets the signal format.

• “Auto”

SQUARE or INTERLEAVE are automatically detected.

• “SQUARE”

Treats as Square Division (SQD) signal.

• “INTERLEAVE”

Treats as Two-Sample Interleave Division (2SI) signal.

Function F1

POP

Display Direction

Scan Size

Gamma Select

Color Gamut

Noise Reduction

Zoom

Undef

Sets functions assigned to function buttons.

• “POP”

Switches the screen display between the dual screen (P

out P: a screen is split vertically) and the single screen.

• “Display Direction”

Rotates / ips the screen.

• “Scan Size”

Switches the setting values of “Window Cong” - “Scan

Size” in sequence.

• “Gamma Select”

Switches the setting values of “Video Cong” - “Gamma”

in sequence.

• “Color Gamut”

Changes the color gamut.

• “Noise Reduction”

Changes between the values “Video Cong” and “Noise

Reduction”.

• “Zoom”

Expands the current view on the display.

• “Undef”

No function assigned.

Status Display Continue

3Sec

Off

Sets whether information about the current input signal and

terminal name is displayed.

Information about the resolution at the PC signal input is

also displayed.

Power On Setup Last

PRESET1 to

PRESET5

FACTORY

USER1 to USER10

Settings for switching on can be set in advance.

• “Last”

Starts with last saved state.

• “PRESET1 to PRESET5”

State saved in PRESET is called. Five types of

PRESET are stored in advance in the monitor as xed

data.

• “FACTORY”

Returns to factory settings.

• “USER1 to USER10”

State saved in USER is called. It is possible to store 10

types of data in USER.

Chapter 2 Advanced Adjustment / Setting

Function Setting range Description

Power Save Mode On

Off

Sets whether function that the backlight turns off due to no

video signal after 30 sec is valid.

Language English

Deutsch

Français

日本語

Italiano

Español

Svenska

簡体中文

繁體中文

Sets the language to be used for display in settings and all

menus.

Logo Display On

Off

The logo display on power-on can be set to On or Off.

10 Chapter 2 Advanced Adjustment / Setting

●WindowCong

Settings for screen display.

Function Setting range Description

Multi Window Off

2POP

Sets dual screen display.

• “Off ”

Sets single screen display mode

• “2POP ”

Displays split window (P out P).

Display Direction Normal

180°

Mirror

Sets the rotation angle or horizontally ips the main screen and

subscreen.

Note

• When “180°” is selected , it will be displayed on the screen.

• When “Mirror” is selected , it will be displayed on the screen.

Scan Size (When Multi

Window mode is

set to “Off”)

Normal

Through

Sets zoom in and out ratios when displaying input video on the

monitor.

• “Normal”

When using the single screen, enlarges or reduces so that the

vertical resolution is 2160 dots. Dark bands form left and right

when the aspect ratio is other than 16:9.

• “Through”

Dot-by-dot display.

• “H Fit”

The input signal will ll the POP horizontally.

• “V Fit”

Displays the input signal matching the vertical display frame of

the POP.

(When Multi

Window mode is

set to “2POP”)

H Fit

V Fit

Zoom 1.5

2.0

Setting for the zoom percentage when an image is zoomed.

• “1.5”

Expand by 1.5.

• “2.0”

Expand by 2.0.

Andere Handbücher für CuratOR EX3140

Inhaltsverzeichnis

Andere Eizo Monitor Handbücher

Eizo

Eizo DuraVision FDX1003 Benutzerhandbuch

Eizo

Eizo FLEXSCAN T960 - Bedienungsanleitung

Eizo

Eizo FlexScan S1932 Bedienungsanleitung

Eizo

Eizo Raptor SQ2801 Bedienungsanleitung

Eizo

Eizo RadiForce RS210 Bedienungsanleitung

Eizo

Eizo FlexScan S2402W Bedienungsanleitung

Eizo

Eizo RadiForce MS231WT Bedienungsanleitung

Eizo

Eizo FLEXSCAN L887 Bedienungsanleitung

Eizo

Eizo FlexScan S2401W Benutzerhandbuch

Eizo

Eizo FlexScan EV2760 Bedienungsanleitung

Eizo

Eizo ColorEdge CG245W Bedienungsanleitung

Eizo

Eizo EIZO ColorEdge CG241W Benutzerhandbuch

Eizo

Eizo FC-2090C Bedienungsanleitung

Eizo

Eizo FORIS FS2332 - Bedienungsanleitung

Eizo

Eizo FlexScan EV2780-BK Bedienungsanleitung

Eizo

Eizo EX1 Bedienungsanleitung

Eizo

Eizo FlexScan L797-U Bedienungsanleitung

Eizo

Eizo ColorEdge CG246 Bedienungsanleitung

Eizo

Eizo CuratOR EX3242-3D Bedienungsanleitung

Eizo

Eizo FlexScan EV2023W Bedienungsanleitung

Eizo

Eizo Radiforce GX550 Bedienungsanleitung

Eizo

Eizo FlexScan L 560T L560T-C L560T-C Bedienungsanleitung

Eizo

Eizo FlexScan L778 Bedienungsanleitung

Eizo

Eizo FLEXSCAN S1701-X - Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung