EK EK-FB SR2 Leitfaden

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the

liquid seal is made using o-rings.

STEP 1: GENERAL INFORMATION Sam

hoto of EVGA SR2 CLASSIFIED PCB desi

STEP 2: PREPARING YOUR MOTHERBOARD

1. REMOVING STOCK COOLER. Remove all encircled screws. All stock

cooler assembly screws should be removed. There are 14 screws on the back

of the motherboard.

2. CLEANING THE PCB. Carefully detach the original stock cooler after removing all screws

securing it to the board. Wipe off the remains (by using non–abrasive cloth or qtip, as shown

on sample photo) of the original thermal compound until the components and circuit board are

completely clean. EKWB does not recommend using any liquids for removing paste.

3. APPLYING THERMAL COMPOUND

Apply thermal compound: put a small drop of thermal compound on the chips

marked in substep 5. For example Céramique™ thermal compound. Follow this

link http://www.arctic-

cooling.com/catalog/product_info.php?cPath=39_&mID=127&language=en

for detailed instructions. EKWB recommends non-conductive MX-2, which

should be applied in cross form for best performance (see sample picture).

4. CUTTING THERMAL PADS. Three types of thermal pads are enclosed with your water

block. (WARNING: DIMENSIONS ON PICTURES BELLOW ARE SCALED!)

5. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads you cut on PCB as shown on picture bellow.

(PLEASE REMOVE FOIL OF THERMAL PADS PRIOR TO INSTALLATION.)

Installation and mounting manual for EK-FB SR2 water block:

Alldisclosures,noticesandwarrantyconditionsarebeingwrittenonthebackofthebox. Releasedon28thofJuly,2010.

Stockcooler

Mosfets

CPUsocket

Apply thermal grease on

Northbridge and Southbridge.

Mosfets

Place 0,5mm thick thermal pads

Place 1mm thick thermal

ads here.

Place 1,5mm thick thermal pads here.

Place 1mm thick thermal pads here.

1mmthick

0,5mmthick1,5mmthick

Place 0

5mm thick thermal

ads here.

STEP 3: PREPARING YOUR WATER BLOCK

1. ATTACHING STANDOFFS. Apply small amount of thermal grease around mounting

holes (FB and separated mosfet block) and place acetal standoffs (thickness 2,1 mm)

so the holes are concentric. Thermal paste provides enough adhesive force for

standoffs to stay in a place.

2. PLACING BLOCK OVER GPU. Place the motherboard on the inverted water block(s)

or vice versa and attach them one at the time with enclosed screws as shown in step 4

and 5. Make sure that mounting holes are aligned.

STEP 4: ATTACHING FB BLOCK TO MOTHERBOARD STEP 5: ATTACHING MSOFET BLOCK TO MOTHERBOARD

1. MOUNTING THE BLOCK.

Tightening the screws beginning in the center of the block near the

northbridge, and continue evenly outwards. Do not use too much

pressure

on screws, because motherboard might

bend and either

cause bad contact with water block, or break a connection on the board.

Use the enclosed screws and washers as shown in diagram below:

6. POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT

Please use enclosed spacer on shown (see sample picture). Attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. EKWB recommends using high

flow fittings with the EK-FB SR2 series water blocks. To ensure that the tubes are securely attached to the barb/fittings, please use hose clamps or an appropriate substitute.

The use of an algaecide is always recommended for any liquid cooling system.

You can use any hole as an inlet/outlet hole.

STEP 7: CHECKING FOR CONTACTS

Temporarily r

emove the water block to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat

steps 3 and 5 to reattach the block applying more or less pressure to the areas where you have found it necessary.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver 9 screws M2,5 x 6 DIN7985 4 screws M2,5 x 8 DIN7985 

Please use the stock backplate and

M2,5x8mm screws on mosfet area.

Please use the stock backplate and

M2,5x8mm screws on mosfet area.

M2,5x6 screws

Washer

Fitting/barb

Spacer

Washer

Andere EK Computerhardware Handbücher

EK Pro RTX A5000 Rack Bedienungsanleitung

EK Quantum Velocity2 1700 Bedienungsanleitung

EK Nucleus AIO CR360 Lux Direct Die D-RGB -... Bedienungsanleitung

EK Pro LGA 1700 Bedienungsanleitung

EK EK-Mana G2 PC-O11D EVO DDC D-RGB Bedienungsanleitung

EK EK-Quantum Vector Red Devil RX 6800/6900 Bedienungsanleitung

EK Quantum Scalar2 Direct Link Side Port Terminal -... Bedienungsanleitung

EK EK-Quantum Vector N+ RX 6800XT Bedienungsanleitung

EK Convection DDC Bedienungsanleitung

EK EK-Mana MSI MAG Z690 TORPEDO EK X D-RGB Bedienungsanleitung

EK Vertical GPU Holder EVO Bedienungsanleitung

EK Quantum Magnitude sTRX5 Bedienungsanleitung

EK Quantum Reflection Evolv X Bedienungsanleitung

EK Quantum PC-O11D XL D5 PWM D-RGB Bedienungsanleitung

EK Vector TRIO RTX 3080 Bedienungsanleitung

EK Quantum Vector2 RE RTX 3080 ABP Set D-RGB Bedienungsanleitung

EK EK-Quantum Momentum ROG Rampage VI Encore Bedienungsanleitung

EK Loop Vertical GPU Holder EVO Gen4 Riser Bedienungsanleitung

EK Quantum Vector2 RE RTX 3080 ABP Set D-RGB Bedienungsanleitung

EK Quantum Momentum2 Pro WS W790-ACE Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung