Ekwb EK-FB ASRock X399 RGB Monoblock Bedienungsanleitung

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.1. Published on May 28th 2018

REMOVING STOCK COOLER. Remove all encircled screws. There are 5 (five) screws

on the back of the motherboard that need to be removed in order to remove the

factory installed MOSFET heatpipe cooling solution.

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no

liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.

Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

Before you start using this product please follow these basic guidelines:

1. Please carefully read the manual thoroughly before beginning with the installation process!

2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).

3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.

4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.

STEP 1: GENERAL INFORMATION Sample photo of ASRock Fatal1ty X399 Professional Gaming motherboard

BAG CONTENT: Bag content is universal for all water blocks, you may not need all screws.

STEP 2: PREPARING YOUR MOTHERBOARD

STEP 3: PREPARING YOUR MOTHERBOARD

APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat spreader

(IHS) - see sample photo below with enclosed thermal grease.

The quantity of about two stripes is just about right. There is no need to cover the

whole IHS. Applying too much thermal grease will have negative impact on the cooling

performance!

STEP 4: CUTTING THERMAL PADS

STEP 5: PREPARING THE MONOBLOCK

Your block comes with thermal pads which needs to be trimmed in order to fit the

voltage regulation area (MOSFET) on the motherboard’s circuit board. WARNING:

DIMENSIONS ON PICTURES BELOW ARE SCALED.

Replacement thermal pads @ EKWB web shop:

Thermal PAD G 1mm - (120x24mm) [EAN: 3830046996770]

Thermal PAD F 2mm - (120x16mm) [EAN: 3830046996756]

Place the M2,5 self-adhesive PVC washers under marked standoffs on monoblock and

heatsink!

Installation manual for EK-FB ASRock X399 RGB Monoblock water block

Mosfets

CPU socket

AMD X399

Chipset

1. Thermal pad G–1.0mm

(for mosfets, inductor coils and

ethernet chip):

2. Thermal pad F–2.0mm

(for mosfets):

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 1.1. Published on May 28th 2018

Place thermal pads on PCB as shown on the picture below.

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL

PADS PRIOR TO INSTALLATION!

STEP 6: PLACING THERMAL PADS

STEP 7: PLACING A BLOCK ON TO THE MOTHERBOARD

Place the EK-FB ASRock X399 RGB Monoblock and heatsink gently to the motherboard

or vice versa (as shown on photo below). Make sure that mounting holes are aligned.

STEP 8.1: ATTACHING A BLOCK ON TO THE MOTHERBOARD

STEP 8.2: ATTACHING A BLOCK ON TO THE MOTHERBOARD

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block. Secure top 4 (four)

nickel screws with enclosed 2,5mm Allen key. Tighten screws diagonally and evenly

till the end of the thread. Do not use excessive force when tightening the screws!

Prior to fastening the screws please make sure the mounting holes on the

motherboard’s circuit board are aligned with the water block. Use 2 (two) M2,5x5

DIN7985 screws with M2.5 PVC washers and 3 (three) M2,5x5 AX1 screws with M2.5

PVC washers. Tighten the screws evenly. Do not use excessive force when tightening

the screws!

STEP 9: CONNECTING THE RGB LED STRIP (optional)

Plug the 4-pin connector from Monoblock RGB LED strip to the RGB_LED header on

your motherboard. Please ensure that the arrow indicated on the connector is

plugged into the 12V line as indicated on your motherboard. Failure to do so will

damage your motherboard or LED strip.

For the EK-FB ASRock X399 Monoblock series water block to operate properly the lower

G1/4 port of the water block MUST BE USED AS THE INLET PORT. EK recommends

the use of EK-ACF fittings. When using fittings other than EK-ACF series please use

hose clamps or appropriate substitute to secure the tubing to the barb. The use of

biocide containing and corrosion inhibiting coolant is always recommended for any

liquid cooling system.

REQUIRED TOOLS AND MOUNTING SCREWS:

scissors philips screwdriver Allen key

M2.5x5 AX1 screws

Tubing

IMPORTANT: USE

THIS OPENING AS

AN INLET PORT!

Place 1mm thermal pads in

large strip over marked area

and make sure all mosfet chips

and inductor coils are covered.

Also place 1mm thermal pad

over AQUANTIA® 10 Gigabit

LAN chip (only on Fatal1ty

motherboard)

M2.5 PVC

washers

Place 2mm

thermal pads

in large strip

over marked

area and

make sure all

mosfet chips

are covered.

M2.5x5 DIN7985

Dieses Handbuch passt für folgende Modelle

Andere ekwb Computerhardware Handbücher

ekwb

ekwb EK-FC980 GTX Classy Handbuch

ekwb

ekwb EK-FC 770 GTX DCII Handbuch

ekwb

ekwb EK-FC7870 GTX Handbuch

ekwb

ekwb EK-Supreme HF Leitfaden

ekwb

ekwb EK-FC Terminal Bedienungsanleitung

ekwb

ekwb EK-DBAY DCP 2.2 Handbuch

ekwb

ekwb EK-FC 5870 MSI Handbuch

ekwb

ekwb EK-FC 5970 Handbuch

ekwb

ekwb EK-FC780 GTX Ti Matrix Handbuch

ekwb

ekwb EK-FB ASUS R5-E10 Leitfaden

ekwb

ekwb EK-FB MSI X299 GAMING PRO CARBON Monoblock Bedienungsanleitung

ekwb

ekwb EK-Nucleus AIO CR360 Lux D-RGB Bedienungsanleitung

ekwb

ekwb EK-PRO GPU WB AMP-Trinity RTX 4090 Ni+Inox Bedienungsanleitung

ekwb

ekwb EK-FB EVGA X58 CLASSIFIED Bedienungsanleitung

ekwb

ekwb EK-XRES Revo D5 Bedienungsanleitung

ekwb

ekwb EK-Vector Radeon VII Bedienungsanleitung

ekwb

ekwb EK-FB KIT RE4 Handbuch

ekwb

ekwb EK-PRO GPU WB RTX A100 80GB Bedienungsanleitung

ekwb

ekwb EK-FC R9 Nano Series Handbuch

ekwb

ekwb EK-FC1080 GTX Ti FTW3 Bedienungsanleitung

ekwb

ekwb CPU Lignum Bedienungsanleitung

ekwb

ekwb EK-FB ASUS P7P55 KIT Leitfaden

ekwb

ekwb EK-FC 780 GTX Ti DCII Handbuch

ekwb

ekwb EK-Vector Radeon RX5700 + XT Backplate Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung

ekwb EK-FB ASRock X399 RGB Monoblock Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken