Ekwb EK-Quantum Momentum ROG Crosshair VIII Hero Bedienungsanleitung

USER GUIDE

EK-Quantum

Momentum ROG Crosshair VIII Hero

MONOBLOCK

This product is intended for installation only by expert users.

Please consult with a qualiﬁed technician for installation. Improper

installation may result in damage to your equipment. EK Water Blocks

assumes no liability whatsoever, expressed or implied, for the use of

these products, nor their installation. The following instructions are

subject to change without notice. Please visit our web site at www.

ekwb.com for updates. Before installation of this product please

read important notice, disclosure and warranty conditions printed

on the back of the box.

Before you start using this product please follow these basic guidelines:

Please carefully read the manual thoroughly before beginning

with the installation process!

Please remove your motherboard from the computer to assure

safest mounting process in order to prevent any possible

damages to your CPU and/or motherboard’s circuit board (PCB).

The EK- Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber o-ring gaskets.

The use of quality, market proved corrosion inhibiting coolants

is always strongly recommended for any liquid cooling system.

- 3 -

TABLE OF CONTENT

PREPARING YOUR MOTHERBOARD 4

REMOVING STOCK COOLER 4

REMOVING OF THE ORIGINAL PLASTIC HOLDDOWN AND THE FACTORY BACKPLATE 5

APPLYING THERMAL COMPOUND 6

CUTTING THERMAL PADS 6

PLACING THERMAL PADS ON THE MOTHERBOARD 6

PLACING THE BLOCK ON TO MOTHERBOARD 7

ATTACHING BLOCK ON THE MOTHERBOARD 7

CONNECTING THE DRGB LED STRIP 8

REQUIRED TOOLS 9

SUPPORT AND SERVICE 10

SOCIAL MEDIA 10

- 4 -

PREPARING YOUR MOTHERBOARD

REMOVING STOCK COOLER

Remove all encircled screws. There are 4 screws on the back of the

motherboard, that need to be removed in order to remove the factory

installed MOSFET cooling solution. Additional 4 screws need to be

removed to remove I/O cover. You can attach the I/O cover back,

after you mount the Monoblock.

I/O Cover screws

Mosfet screws

- 5 -

REMOVING OF THE ORIGINAL PLASTIC

HOLD-DOWN AND THE FACTORY

BACKPLATE

Using Philips-head screwdriver remove the four UNC 6-32 screws

securing the original plastic hold-down clamps around the socket as

shown on the sketch. Remove the original backplate and the hold-

down clamps.

UNC 6-32 Screws

Factory

Backplate

- 6 -

APPLYING THERMAL COMPOUND

Apply thermal compound on CPU heat spreader (IHS) with enclosed

EK-TIM Ectotherm thermal grease. The quantity of about two rice

grains is just about right. There is no need to cover the whole IHS.

Applying too much thermal grease will have negative impact on the

cooling performance!

CUTTING THERMAL PADS

Your block comes with thermal pads which needs to be trimmed

in order to ﬁt the voltage regulation area (MOSFET) on the

motherboard’s circuit board.

WARNING: Dimensions on pictures below are scaled.

PLACING THERMAL PADS ON THE

MOTHERBOARD

Place thermal pads on PCB as shown on the picture.

Please remove the protective foil from both sides of the

thermal pads prior to installation!

Place 1mm Thermal Pads in larger strips over the marked

area and make sure all mosfet and inductor chips are covered.

Thermal Pad F – 1.0 mm

120

- 7 -

PLACING THE BLOCK ON TO MOTHERBOARD

Place the EK-Quantum Momentum ROG Crosshair VIII Hero

Monoblock series water block gently to the motherboard or vice

versa (as shown on the photo below). Make sure that mounting holes

are aligned.

ATTACHING BLOCK ON THE MOTHERBOARD

STEP 1

Prior to fastening the screws please make sure the mounting holes

on the motherboard’s circuit board are aligned with the water block.

Mosfet part: Use four (4) M2,5x5 AX1 screws with PVC washers.

Tighten the screws evenly. Do not use excessive force when

tightening the screws!

CPU part: Use four (4) M3x10 DIN7984 with screws. Tighten the

screws using enclosed 2 mm Allen key.

STEP 1

M2.5 PVC

washers M3x10 Screws

M2.5x5 Screws

AM4 Backplate

Insulator

- 8 -

STEP 2

For the EK- Quantum Momentum ROG Crosshair VIII Hero

Monoblock series water block to operate properly the G1/4 port

nearest to the right edge of the water block MUST BE USED AS

THE INLET PORT.

EK recommends the use of EK- Fittings. When using ﬁttings other

than EK series please use hose clamps or appropriate substitute

to secure the tubing to the barb. The use of biocide containing and

corrosion inhibiting coolant is always recommended for any liquid

cooling system.

CONNECTING THE D-RGB LED STRIP

Plug the 3-pin connector from Monoblock D-RGB LED strip to the

motherboard.

Please ensure that the arrow indicated on the connector is

plugged into the +5V line as indicated on your motherboard.

Failure to do so will damage your motherboard or LED strip.

STEP 2

D-RGB Header

RGB Header

IMPORTANT:

Use this opening

as an Inlet Port!

- 9 -

REQUIRED TOOLS

Phillips-head screwdriver Scissors

Allen Key

For assistance please contact:

http://support.ekwb.com/

EKWB d.o.o.

Pod lipami 18

1218 Komenda

Slovenia - EU

EKWaterBlocks

@EKWaterBlocks

ekwaterblocks

EKWBofﬁcial

SUPPORT AND SERVICE

SOCIAL MEDIA

Inhaltsverzeichnis

Andere ekwb Computerhardware Handbücher

ekwb

ekwb 3831109831618 Leitfaden

ekwb

ekwb EK-FC980 GTX Ti WF3 Handbuch

ekwb

ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Bedienungsanleitung

ekwb

ekwb EK-Vector Radeon RX5700 + XT Backplate Bedienungsanleitung

ekwb

ekwb EK-Classic GPU Water Block RTX 3080/3090... Bedienungsanleitung

ekwb

ekwb EK-FC590 GTX Handbuch

ekwb

ekwb EK-FC 780 GTX Ti DCII Handbuch

ekwb

ekwb EK-FB KIT ASUS R5E Leitfaden

ekwb

ekwb EK-FC780 GTX Ti Series Bedienungsanleitung

ekwb

ekwb EK-PRO GPU WB RTX 30x0 Bedienungsanleitung

ekwb

ekwb EK-FC Titan X Leitfaden

ekwb

ekwb EK-Quantum Vector Trinity RTX 3080/3090 Bedienungsanleitung

ekwb

ekwb EK-Quantum Vector Trinity RTX 3080/3090 Bedienungsanleitung

ekwb

ekwb EK X Series Bedienungsanleitung

ekwb

ekwb EK-Vector FTW3 RTX 2080 Ti Leitfaden

ekwb

ekwb Velocity-AMD Bedienungsanleitung

ekwb

ekwb EK-XTOP Revo D5 PWM Handbuch

ekwb

ekwb EK-FC 770 GTX DCII Handbuch

ekwb

ekwb EK-Supremacy EVO X99 Series Bedienungsanleitung

ekwb

ekwb EK-QuantumX Delta TEC Bedienungsanleitung

ekwb

ekwb EK-FB ASUS P7P55 KIT Leitfaden

ekwb

ekwb EK-Classic GPU Water BlockRTX 2080Ti D-RGB Bedienungsanleitung

ekwb

ekwb EK-FCTK20 Leitfaden

ekwb

ekwb EK-RES X3 Series Handbuch

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung

ekwb EK-Quantum Momentum ROG Crosshair VIII Hero Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken