Elatec TWN4 MultiTech 2 HF Bedienungsanleitung

TWN4

MultiTech Mini

DocRev5, February 5, 2019

Elatec GmbH

Contents

1Introduction............................................... 3

2Dimensions............................................... 4

3Connectors............................................... 5

4UsingPIOption ............................................ 6

4.1 SIO Chip soldered on PCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4.2 SAM Card Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5Disclaimer ............................................... 7

Page 2of 7

1 Introduction

TWN4 MultiTech Mini is a module to be integrated on custom PCB. It has a built-in HF antenna and subset

of IOs compared to TWN4 Core Module. TWN4 Mini Reader is currently available as version TWN4 Mini

Reader MIFARE NFC.

Page 3of 7

2 Dimensions

Below are the dimensions of the TWN4 MultiTech Mini. All dimensions in mm unless otherwise stated.

Page 4of 7

3 Connectors

The TWN4 Mini Reader has two on-board single row headers with 8 positions each. The pins of these two

connectors are together enumerated from 1 to 16.

• Single row header

• Pitch 2.54mm

• Pin shape square 0.635mm

Pin Pin Name Function

1 RESET- Low active TTL input with internal pull-up resistor for hard re-

set.

2 PWRDWN- Low active TTL input with internal pull-up resistor for turning

off the voltage regulator.

3 GND Ground

4 VIN Unregulated input to on-board voltage regulator

5 RXD- Low active TTL input with internal pull-up resistor of asyn-

chronous RXD to COM1.

6 TXD- Low active TTL output (push/pull) of asynchronous TXD from

COM1.

7 Res. Reserved for future use (intended for SCK from SPI host in-

terface).

8 Res. Reserved for future use (intended for SS- from SPI host inter-

face).

9 VCC Internaly regulated 3.0V power supply. To be used for SAM1.

10 SAM_IO I/O line for SAM1.

11 GPIO3 GPIO3, I/O pin for general purposes.

12 GPIO2 GPIO2, I/O pin for general purposes.

13 GPIO1 GPIO1, I/O pin for general purposes.

14 GPIO0 GPIO0, I/O pin for general purposes.

15 SAM_CLK Clock output for SAM1

16 SAM_RST Reset output for SAM1

Page 5of 7

4 Using PI Option

To use the PI Option, e.g. to read the PAC bits from an iCLASS transponder, a SIO processor is needed.

This can be either a SIO chip which is soldered directly on a PCB or a SAM card incorporating the SIO

processor.

4.1 SIO Chip soldered on PCB

The SIO processor has to be added to the design of the mainboard. The chip shall be connected to the

SAM-pins of the TWN4 Mini Reader.

Recommended schematic:

4.2 SAM Card Connection

A SAM socket has to be added to the design of the mainboard. The SAM socket shall be connected to the

SAM-pins of the TWN4 Mini Reader.

Following SAM sockets are recommended:

• Molex 47388-2001

• Molex 47308-0001

Recommended schematic:

Page 6of 7

5 Disclaimer

Elatec reserves the right to change any information or data in this document without prior notice. The

distribution and the update of this document is not controlled. Elatec declines all responsibility for the use

of product with any other speciﬁcations but the ones mentioned above. Any additional requirement for a

speciﬁc custom application has to be validated by the customer himself at his own responsibility. Where

application information is given, it is only advisory and does not form part of the speciﬁcation.

All referenced brands, product names, service names and trademarks mentioned in this document are the

property of their respective owners.

Page 7of 7

Andere Handbücher für TWN4 MultiTech 2 HF

Inhaltsverzeichnis

Andere Elatec Steuereinheit Handbücher

Elatec

Elatec TWN4 MultiTech 2 HF Versionshinweis

Elatec

Elatec TWN4 MULTITECH LEGIC M Gebrauchs- und Pflegehandbuch

Elatec

Elatec TWN4 MultiTech 2 HF Bedienungsanleitung

Elatec

Elatec TWN4 Slim LEGIC Bedienungsanleitung

Elatec

Elatec TWN4 MultiTech 2 HF Bedienungsanleitung

Elatec

Elatec TWN4 MULTITECH LEGIC M Bedienungsanleitung

Elatec

Elatec TCP3 3.0.3.1 Bedienungsanleitung

Elatec

Elatec TWN3 MINI Bedienungsanleitung

Elatec

Elatec TWN4 PALON SQUARE M LF HF Bedienungsanleitung

Elatec

Elatec TWN3 LEGIC NFC Bedienungsanleitung

Elatec

Elatec TWN4 PALON SQUARE M LF HF Gebrauchs- und Pflegehandbuch

Elatec

Elatec TWN4 MultiTech 2 HF Bedienungsanleitung

Elatec

Elatec TWN3 LEGIC NFC M Bedienungsanleitung

Elatec

Elatec TWN4 MultiTech 2 HF Gebrauchs- und Pflegehandbuch

Elatec

Elatec TWN3 MIFARE Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung