Elation PROTEUS RAYZOR 760 Bedienungsanleitung

User Manual

PROTEUS

RAYZOR 760 /

RAYZOR 760 WMG

images, and instructions herein are subject to change without notice. ELATION PROFES-

SIONAL logo and identifying product names and numbers herein are trademarks of ELATION

PROFESSIONAL. Copyright protection claimed includes all forms and matters of copyrightable

materials and information now allowed by statutory or judicial law or hereinafter granted.

Product names used in this document may be trademarks or registered trademarks of their

respective companies and are hereby acknowledged. All non-ELATION brands and product

names are trademarks or registered trademarks of their respective companies.

ELATION PROFESSIONAL and all a󰤳liated companies hereby disclaim any and all liabilities

for property, equipment, building, and electrical damages, injuries to any persons, and direct

or indirect economic loss associated with the use or reliance of any information contained

within this document, and/or as a result of the improper, unsafe, insu󰤳cient and negligent

assembly, installation, rigging, and operation of this product.

Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040

323-582-3322 | 323-832-9142 fax | www.elationlighting.com | info@elationlighting.com

Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands

+31 45 546 85 66 | +31 45 546 85 96 fax | www.elationlighting.eu | info@elationlighting.eu

Elation Professional Mexico

AV Santa Ana 30 | Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

Date Document

Version

Software

Version DMX Channels Notes

05/28/2019 1.0 1.2.1 25 / 52 / 80 Initial release

09/30/2019 1.1 N/C No Change Included RJ4 data cable note.

10/15/2019 2.0 1.2.2 No Change Updated System sub menus, DMX Control

Channel, RGBW/ SparkLED FX Tables

03/05/2020 2.5 N/C No Change Added torque screw setting page

05/12/2020 3.0 N/C No Change Added Elation Proteus Rayzor 760 WMG

08/10/2020 3.5 N/C No Change Updated thermal

10/14/2020 4.0 N/C No Change Updated specifications

02/04/2021 4.5 1.2.4 No Change Updated primary/secondary modes

03/15/2021 5.0 N/C No Change Hibernation/sun protection warning and

information

05/20/2021 5.5 N/C No Change Updated Maintenance Guidelines

08/15/2022 6.0 N/C No Change

Updated Introduction, System Menu, DMX

Traits, and Torque settings for screws;

added RDM; updated formatting

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version

of this document may be available online. Please check www.elationlight-

ing.com for the latest revision/update of this manual before beginning

installation and/or programming.

TABLE OF CONTENTS

Introduction 4

Warranty Returns 5

Safety Precautions 6

Maintenance Guidelines 8

Overview 9

Installation Guidelines 10

Torque Settings for Screws 15

Remote Device Management (RDM) 17

System Menu 18

Record Controller 22

Lighting Console Patching Guidelines 25

DMX Traits 30

Color Temperature Control Table 39

FX Generator Guidelines 41

RGBW FX Table 43

Spark LED FX Table 48

Error Codes 53

Specifications 54

Dimensional Drawings 55

Optional Accessories | FCC Statement 56

Please read and understand the instructions in this manual carefully and thoroughly before

attempting to operate this device. These instructions contain important safety and use infor-

mation. This device is intended for use by trained personnel only, and is not suitable for

private use.

UNPACKING

Every device has been thoroughly tested and has been shipped in perfect operating condition.

Carefully check the shipping carton for damage that may have occurred during shipping. If the

carton is damaged, carefully inspect the device for damage, and be sure all accessories neces-

sary to install and operate the device have arrived intact. In the event that damage has been

found or parts are missing, please contact our customer support team for further instructions.

Please do not return this device to your dealer without 󰤱rst contacting customer support.

Please do not discard the shipping carton in the trash. Please recycle whenever possible.

IP65 RATED

An IP rated lighting 󰤱xture is commonly installed in outdoor environments and has been designed

with an enclosure that e󰤰ectively protects against the ingress (entry) of external foreign

objects such as dust and water. The International Protection (IP) rating system is commonly

expressed as “IP” followed by two numbers (i.e. IP65) where the numbers de󰤱ne the degree

of protection. The 󰤱rst digit (Foreign Bodies Protection) indicates the extent of protection

against particles entering the 󰤱xture, while the second digit (Water Protection) indicates the

extent of protection against water entering the 󰤱xture. An IP65 rated lighting 󰤱xture, such

as this one, has been designed and tested to protect against the ingress of dust (6) and

low-pressure water jets from any direction (5).

BOX CONTENTS

Omega Brackets (x2)

IP65 Rated 5-pin DMX Cable (x1)

IP65 Rated RJ45 Data Cable (x1) - FIXTURE TO FIXTURE INTERCONNECTION USE ONLY!

IP65 Locking Power Cable (x1)

CUSTOMER SUPPORT

Contact ELATION Service for any product related service and support needs.

Also visit forums.elationlighting.com with questions, comments or suggestions.

ELATION SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

323-582-3322 | Fax 323-832-9142 | support@elationlighting.com

ELATION SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

+31 45 546 85 63 | Fax +31 45 546 85 96 | support@elationlighting.eu

REPLACEMENT PARTS - please visit parts.elationlighting.com

INTRODUCTION

WARRANTY RETURNS (USA ONLY)

To obtain warranty service, a Return Materials Authorization (RMA) number must first be

obtained from ELATION. It is the Customer’s responsibility to provide product proof of

purchase and serial number by acceptable evidence such as an invoice copy or an approved

ELATION Extended Warranty Certificate (“EWC”) and any relevant maintenance records at the

time warranty service is sought. Failure to provide acceptable evidence of product proof of

purchase or EWC and any relevant maintenance records may be cause for denial of warranty

service.

Products returned for warranty service must be sent without any accessories (i.e., power,

data, and safety cables, brackets, clamps, rigging hardware, frost filters, gel frames, barn

doors, lens, hoses, nozzles, rack mounting hardware, etc.), must be boxed using the original

and/or suitable packaging materials (double-box and foam) that provides ample product pro-

tection for ground and/or air freight transit, and must be shipped freight pre-paid and insured

to ELATION in Los Angeles, CA or an ELATION Authorized Service Center. The RMA number

must be clearly written on the outside of the return box, and a brief description of the prob-

lem and the RMA number must be documented and included in the box.

Products returned for warranty service without an RMA number clearly marked on the out-

side of the package will be refused and returned to the shipper at the Customer’s expense.

Products returned for warranty service, which are received damaged due to inadequate and/

or improper packaging and/or due to damage caused by shipping carrier, may incur addi-

tional repair charges before warranty service begins and/or may void this warranty. If any

product accessories (included and/or optional) are shipped with the product, ELATION and/

or the ELATION Authorized Service Center shall have no liability what so ever for the loss

and/or damage to any such accessories, nor the safe return thereof. If the requested war-

ranty repairs or service (including parts replacement) are within the terms of this warranty,

ELATION will pay return ground transportation shipping charges to a single designated point

within the United States.

SAFETY PRECAUTIONS

PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED.

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT

ANY REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER’S

WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE

AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS

MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO

ANY WARRANTY CLAIMS AND/OR REPAIRS.

NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!

RETINA INJURY RISK - MAY INDUCE BLINDNESS!

SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

This 󰤱xture is a sophisticated piece of electronic equipment. To guarantee a smooth opera-

tion, it is important to follow all instructions and guidelines in this manual. Elation Profes-

sional is not responsible for injuries and/or damages resulting from the misuse of this 󰤱xture

due to the disregard of the information printed in this manual. Only quali󰤱ed and/or certi󰤱ed

personnel should perform installation of this 󰤱xture and only the original rigging parts in-

cluded with this 󰤱xture should be used for installation. Any modi󰤱cations to the 󰤱xture and/

or the included mounting hardware will void the original manufacturer’s warranty and in-

crease the risk of damage and/or personal injury

DO NOT PLUG FIXTURE INTO A DIMMER PACK!

NEVER OPEN THIS FIXTURE WHILE IN USE!

UNPLUG POWER BEFORE SERVICING FIXTURE!

NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT! KEEP

FLAMMABLE MATERIALS AWAY FROM FIXTURE!

ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A

DIELECTRIC GREASE (AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO PREVENT

WATER CORROSION AND/OR ELECTRICAL SHORT CIRCUIT.

MINIMUM DISTANCE TO OBJECTS/SURFACES

MUST BE 3.3 FEET (1 METER)

MAXIMUM TEMP OF EXTERNAL SURFACE 185° F (85°C)

MINIMUM DISTANCE OF FLAMMABLE MATERIALS FROM THE SURFACE IS 1.6 FEET

(0.5 METER)

SAFETY PRECAUTIONS

• DO NOT TOUCH the 󰤱xture housing during operation. Turn OFF the power and allow ap-

proximately 15 minutes for the 󰤱xture to cool down before servicing.

• DO NOT shake 󰤱xture, and avoid brute force when installing and/or operating 󰤱xture.

• DO NOT operate 󰤱xture if the power cord is frayed, crimped, damaged and/or if any of the

power cord connectors are damaged and do not insert into the 󰤱xture securely with ease.

• NEVER force a power cord connector into the 󰤱xture. If the power cord or any of its con-

nectors are damaged, replace it immediately with a new one of the same power rating.

• DO NOT block any air ventilation slots.

• All fan and air inlets must remain clean and never blocked.

• Allow approx. 6” (15cm) between 󰤱xture and other devices or a wall for proper cooling.

• Always disconnect 󰤱xture from main power source before performing any type of service

and/or cleaning procedure.

• Only handle the power cord by the plug end. Never pull out the plug by tugging the wire

portion of the cord.

• During the initial operation of this 󰤱xture, a light smoke or smell may emit from the inte-

rior of the 󰤱xture. This is a normal process and is caused by excess paint in the interior of

the casing burning o󰤰 from the heat associated with the lamp and will decrease gradually

over time.

• Consistent operational breaks will ensure 󰤱xture will function properly for many years.

• ONLY use the original packaging and materials to transport the 󰤱xture in for service.

MAINTENANCE GUIDELINES

DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!

CLEANING

Frequent cleaning is recommended to ensure proper function, optimized light output, and an

extended life. The frequency of cleaning depends on the environment in which the 󰤱xture

operates: damp, smoky or particularly dirty environments can cause greater accumulation of

dirt on the 󰤱xture’s optics. Periodically clean the external lens surface with a soft cloth to

avoid dirt/debris accumulation. NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

Regular inspections are recommended to ensure proper function and extended life. There are

no user serviceable parts inside this 󰤱xture. Please refer all other service issues to an autho-

rized Elation service technician. Should you need any spare parts, please order genuine parts

from your local Elation dealer.

Please refer to the following points during routine inspections:

• A detailed electric check by an approved electrical engineer every three months, to make

sure the circuit contacts are in good condition and prevent overheating.

• Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall

out during normal operation, resulting in damage or injury as larger parts could fall.

• Check for any deformations on the housing, color lenses, rigging hardware, and rigging

points (ceiling, suspension, trussing). Deformations in the housing could allow for dust to

enter into the 󰤱xture. Damaged rigging points or unsecured rigging could cause the 󰤱xture

to fall and seriously injure a person(s).

• Electric power supply cables must not show any damage, material fatigue or sediments.

NEVER remove the ground prong from the power cable.

FIXTURE DISASSEMBLY

The following points should be observed after performing any maintenance procedure that

requires disassembly of the unit:

• After the unit has been reassembled, open the valve and allow the unit to run for approxi-

mately 2 hours in order to dry out any moisture that has been trapped inside the 󰤱xture.

The process should continue until indicated humidity drops below 15% for the head and

30% for the base.

• Once this has been achieved, the light can be switched o󰤰, but the unit should remain

connected to power so that the cooling fan can cool down the unit. Please note that al-

lowing cool down time should ALWAYS be done after lamp operation.

• Some units may require partial disassembly in order to gain access to the valve. Please

contact Elation service for information regarding the location and access procedure for

the valve on your speci󰤱c unit model.

OVERVIEW

1. Lens

2. System Menu LCD Display

3. Mode/Esc Button

4. Left Button

5. Enter Button

6. Down Button

7. Right Button

8. Up Button

9. Pan Lock

10.Carrying Handle(s)

11.5-pin DMX Output

12.5-pin DMX Input

13.RJ45 Output

14.RJ45 Input

15.Fuse

16.Service Port

17.Value

18.Power Input

INSTALLATION GUIDELINES

FLAMMABLE MATERIAL WARNING

Keep fixture minimum 5.0 feet (1.5m) away from flammable materials and/or pyro-

technics.

Fixture MUST be installed following all local, national, and country commercial electrical and

construction codes and regulations.

Before rigging/mounting a single fixture or multiple fixtures to any metal truss/structure or

placing the fixture(s) on any surface, a professional equipment installer MUST be consulted to

determine if the metal truss/structure or surface is properly certified to safely hold the com-

bined weight of the fixture(s), clamps, cables, and accessories.

Overhead rigging requires extensive experience, including calculating working load limits,

installation material being used, and periodic safety inspection of all installation material and

the fixture, among other skills. If you lack these qualifications, do not attempt the installa-

tion yourself. Improper installation can result in bodily injury.

Fixture ambient operating temperature range is -4° to 113°F (-20° to 45°C). Do not operate

the fixture when the ambient temperature falls outside of this range.

Fixture(s) should be installed away from walking paths, seating areas, or areas were unauthor-

ized personnel might reach the fixture by hand.

NEVER stand directly below the fixture(s) when rigging, removing, or servicing.

Overhead fixture installation must always be secured with a secondary safety attachment,

such as an appropriately rated safety cable.

Allow approximately 15 minutes for the fixture to cool down before serving.

ELECTRICAL CONNECTIONS

A qualified electrician should be used for all electrical connections and/or installa-

tions.

MINIMUM DISTANCE TO SURFACES/OBJECTS IS 3.3 FEET (1 METER).

MINIMUM DISTANCE TO FLAMMABLE MATERIALS IS 1.6 FEET (0.5 METER).

EXTERNAL SURFACE CAN REACH TEMPERATURES OF 185°F (85°C).

DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elation DJ-Equipment Handbücher

Elation

Elation IP GOBO ROTATOR Bedienungsanleitung

Elation

Elation SIXPAR 300 Bedienungsanleitung

Elation

Elation KL FRESNEL 8 Bedienungsanleitung

Elation

Elation FSD 575 Bedienungsanleitung

Elation

Elation TVL551 Bedienungsanleitung

Elation

Elation PROTEUS RAYZOR 760 WMG Bedienungsanleitung

Elation

Elation DESIGN WASH LED ZOOM Bedienungsanleitung

Elation

Elation DTW BLINDER 700 IP Bedienungsanleitung

Elation

Elation CHORUS LINE 16 Bedienungsanleitung

Elation

Elation ARTISTE PICASSO Bedienungsanleitung

Elation

Elation Flex LED Tape WP Bedienungsanleitung

Elation

Elation FUZE WASH 575 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Elation

Elation FUZE PAR Z120 IP Bedienungsanleitung

Elation

Elation DTW PAR 300 Bedienungsanleitung

Elation

Elation CYBER PAK Bedienungsanleitung

Elation

Elation Artiste Van Gogh EAV259 Bedienungsanleitung

Elation

Elation DP-415 Bedienungsanleitung

Elation

Elation KL CYC L Bedienungsanleitung

Elation

Elation Elation Professional Scene Setter Bedienungsanleitung

Elation

Elation ELAR EXTQW BAR HP Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Elation

Elation Elation Fuze Wash 500 WH Bedienungsanleitung

Elation

Elation CHORUS LINE 16 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung

Chauvet

Chauvet ovation B-2805FC Bedienungsanleitung