elco FS200 IM Bedienungsanleitung
Manual
ELCO FS200
IM FS2-GW-DP00
Order No.: ELCO FS2-GW-DP00
This manual is part of the documentation package
with order number ELCO FS200_IM and relevant for:
Product Order number as of state:
HW FW
IM FS200 FS2-GW-DP00 01 2.03
Manual ELCO Intelligent I/O-FS200 About this manual
Subject to change to cater for technical progress.
The information contained in this manual is supplied without warranties.
The information is subject to change without notice.
© Copyright 2011, ELCO(Tianjin)ELECTRONIC CO,.LTD.
Tel.: +86 (22) 23888288/23788282
Fax.: +86 (22) 23788399
http://www.elco-holding.com.cn
Hotline:+86 (22) 23788282
All rights reserved
The contents of this manual were verified with respect to the hard- and
software.
However, we assume no responsibility for any discrepancies or errors. The
information in this manual is verified on a regular basis and any required
corrections will be included in subsequent editions.
Suggestions for improvement are always welcome.
ELCO and FS200
are registered trademarks of ELCO(Tianjin)ELECTRONICS CO,.LTD.
SPEED7
is a registered trademark of profichip GmbH
SIMATIC, STEP and S7-300
are registered trademarks of Siemens AG.
Any other trademarks referred to in the text are the trademarks of the
respective owner and we acknowledge their registration.
Disclaimer of
liability
Trademarks
No.12,4th XEDA Branch Road,Xiqing Economic Development Area,
Tianjin 300385,P.R.China
Tel.: +86 (22) 23888288/23788282
About this manual
Subject to change to cater for technical progress.
About this manual
This manual describes the FS200 bus coupler for Profibus DP of
commissioning and operation.
Chapter 1: Basics and Assembly
found.
Chapter 2: Hardware description
Here the hardware components of the FS200 are more described.
You will find the technical data at the end of this chapter.
Chapter 3: Deployment
This chapter describes the usage of the FS200 with Profibus. After
a short introduction you may find here every information about assembly,
project engineering and diagnostic. The chapter closes with the description
of the firmware update.
Overview
Manual ELCO Intelligent I/O-FS200
the System intelligent I/O from ELCO.
Here you may find every information for
The focus of this chapter is on the introduction of the ELCO Intelligent I/O
Besides the dimensions the general technical data of System FS200 will
be
FS200. Here you will find the information required to assemble and
wire a controller system consisting of System FS200 components.
Manual ELCO intelligent I/O-FS200 Contents
i
Contents
User considerations.................................................................................1
Safety information....................................................................................2
Chapter 1 Basics and Assembly .....................................................1-1
Safety Information for Users................................................................. 1-2
System conception............................................................................... 1-3
Dimensions .......................................................................................... 1-6
Installation............................................................................................ 1-7
Wiring................................................................................................. 1-11
Installation guidelines ......................................................................... 1-14
General data ...................................................................................... 1-17
Chapter 2 Hardware description .....................................................2-1
Properties............................................................................................. 2-2
Structure .............................................................................................. 2-3
Technical data...................................................................................... 2-6
Chapter 3 Deployment .....................................................................3-1
Basics .................................................................................................. 3-2
Project engineering ............................................................................ 3-10
DP-V1 services .................................................................................. 3-13
DP-V1 - I&M data ............................................................................... 3-15
Profibus installation guidelines ........................................................... 3-17
Diagnostic functions ........................................................................... 3-20
Firmware update ................................................................................ 3-28
Contents
ii
Manual ELCO intelligent I/O-FS200
Manual ELCO Intelligent I/O-FS200 User considerations
1
User considerations
This manual describes the FS2-GW-DP00 of the Intelligent I/O from ELCO. It
contains a description of the structure, project engineering and
deployment.
The manual is targeted at users who have a background in automation
technology.
The manual consists of chapters. Every chapter provides a self-contained
description of a specific topic.
The following guides are available in the manual:
• an overall table of contents at the beginning of the manual
• an overview of the topics for every chapter
The manual is available in:
• printed form, on paper
• in electronic form as PDF-file (Adobe Acrobat Reader)
Important passages in the text are highlighted by following icons and
headings:
Danger!
Immediate or likely danger.
Personal injury is possible.
Attention!
Damages to property is likely if these warnings are not heeded.
Note!
Supplementary information and useful tips.
Objective and
contents
Target audience
Structure of the
manual
Guide to the
document
Availability
Icons
Headings
Safety information
2
Safety information
The Intelligent I/O FS200 is constructed and produced for:
• communication and process control
• general control and automation applications
• industrial applications
• operation within the environmental conditions specified in the technical
data
• installation into a cubicle
Danger!
This device is not certified for applications in
• in explosive environments (EX-zone)
The manual must be available to all personnel in the
• project design department
• installation department
• commissioning
• operation
The following conditions must be met before using or commissioning
the components described in this manual:
• Modification to the process control system should only be carried out
when the system has been disconnected from power!
• Installation and modifications only by properly trained personnel
• The national rules and regulations of the respective country must be
satisfied (installation, safety, EMC ...)
National rules and regulations apply to the disposal of the unit!
Applications
conforming with
specifications
Documentation
Disposal
Manual ELCO Intelligent I/O-FS200
Chapter 1 Basics and Assembly
1-1
Chapter 1 Basics and Assembly
The focus of this chapter is on the introduction of the ELCO FS200.
Here you will find the information required to assemble and wire a
controller system consisting of FS200 components.
Besides the dimensions the general technical data of FS200 will be
found.
Topic Page
Chapter 1 Basics and Assembly .....................................................1-1
Safety Information for Users................................................................. 1-2
System conception............................................................................... 1-3
Dimensions .......................................................................................... 1-6
Installation............................................................................................ 1-7
Wiring................................................................................................. 1-11
Installation guidelines ......................................................................... 1-14
General data ...................................................................................... 1-17
Overview
Content
Manual ELCO Intelligent I/O-FS200
Chapter 1 Basics and Assembly
1-2
Safety Information for Users
ELCO modules make use of highly integrated components in MOS-
Technology. These components are extremely sensitive to over-voltages
that can occur during electrostatic discharges.
The following symbol is attached to modules that can be destroyed by
electrostatic discharges.
The Symbol is located on the module, the module rack or on packing
material and it indicates the presence of electrostatic sensitive equipment.
It is possible that electrostatic sensitive equipment is destroyed by energies
and voltages that are far less than the human threshold of perception.
These voltages can occur where persons do not discharge themselves
before handling electrostatic sensitive modules and they can damage
components thereby, causing the module to become inoperable or
unusable.
Modules that have been damaged by electrostatic discharges can fail after
a temperature change, mechanical shock or changes in the electrical load.
Only the consequent implementation of protection devices and meticulous
attention to the applicable rules and regulations for handling the respective
equipment can prevent failures of electrostatic sensitive modules.
Modules must be shipped in the original packing material.
When you are conducting measurements on electrostatic sensitive
modules you should take the following precautions:
• Floating instruments must be discharged before use.
• Instruments must be grounded.
Modifying electrostatic sensitive modules you should only use soldering
irons with grounded tips.
Attention!
Personnel and instruments should be grounded when working on
electrostatic sensitive modules.
Handling of
electrostatic
sensitive modules
Shipping of
modules
Measurements and
alterations on
electrostatic
sensitive modules
Manual ELCO Intelligent I/O-FS200
Manual ELCO Intelligent I/O-FS200 Chapter 1 Basics and Assembly
1-3
System conception
ELCO FS200 is a modular automation system for assembly on a 35mm
mounting rail. By means of the peripheral modules with 2, 4 or 8 channels
this system may properly be adapted matching to your automation tasks.
The wiring complexity is low, because the supply of the DC 24V power
section is integrated to the backplane bus and defective modules may be
replaced with standing wiring.
By deployment of the power modules in contrasting colors within the
system, further isolated areas may be defined for the DC 24V power
section supply.
The FS200 consists of the following components:
• Bus coupler
• Periphery modules
• Power modules
• Accessories
With a bus coupler bus interface and power
module is integrated to one casing. With the bus
interface you get access to a subordinated bus
system.
Via the integrated power module for power supply
the bus interface is supplied as well as the
electronic of the connected periphery modules.
The DC 24 power section supply for the linked
periphery modules is established via a further
connection.
By installing of up to 64 periphery modules at the
bus coupler, these are electrically connected, this
means these are assigned to the backplane bus,
the electronic modules are power supplied and
each periphery module is connected to the DC
24V power section supply.
Overview
Components
Bus coupler
Inhaltsverzeichnis
Andere elco Steuereinheit Handbücher
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
