Eldes EW1 Bedienungsanleitung

WIRELESS ZONE & PGM OUTPUT EXPANSION MODULE

EW1

Wireless expansion module EW1 is a wireless device with 2 zones and 2 PGM outputs. This expansion module connects to ELDES

wireless alarm systems and enables wireless access for to 2 wired devices such as movement PIR sensors, magnetic door contacts etc.

In addition it allows to connect and control up to 2 appliances, i.e. lighting, heating etc. After the wiring process to EW1 it is necessary

to bind EW1 to the alarm system by sending a corresponding command via SMS message or using software ELDES Conguration

Tool. It is possible to connect up to 16 EW1 devices to ELDES alarm system at a time. Minimum distance for wireless connection is 3

centimeters, maximum – 150 meters (in open areas).

1. Package Content

1. EW1 ........................................................qty. 1

2. EW1 User Manual .............................qty. 1

2. Technical Specications

2.1 Electrical & Mechanical Characteristics

Power Supply 7-15V 20mA max

Number of Zones 2

Number of PGM Outputs 2

Wireless Transmitter-Receiver Frequency 868 MHz

Range of Operating Temperatures -20...+55ºC

Dimensions 38x60x12mm

Wireless Communication Range Up to 30 meters in premises; up to 150 meters in open areas

Compatible with Alarm Systems ELDES Wireless

Maximum Allowed Zone Voltage Values 0-30V

Maximum Commuting PGM Output Values Voltage – 30V; current 500mA

2.2 Connector & LED Functionality

COM Common contact for power supply, zones, PGM outputs

Z2, Z1 Security zones

C2, C1 PGM outputs

DC+ Positive power supply contact

D1, D2 Pins for restoring default settings

LED EW1 status

3. Installation

1. Disconnect ELDES alarm system main power supply and backup battery.

2. Connect the circuit as indicated in Fig. No. 2

3. Bind the device to ELDES alarm system. Use ELDES Conguration Tool software or

send a corresponding SMS message. Please refer to software‘s HELP section or

refer to installation manual of ELDES alarm system.

4. The system automatically informs about successful/unsuccessful binding pro-

cess. If attempt to bind is unsuccessful, try to move EW1 closer to ELDES alarm

system device and bind anew.

5. EW1 module is ready for use.

NOTE: If you are unable to bind the wireless device, please, restore the pa-

rameters of the wireless device to default and try again. See chapter 4. Re-

storing Default Parameters for more details.

4. Restoring Default Parameters

1. Disconnect EW1 power supply.

2. Short circuit (connect) pins D1 and D2.

3. Power up EW1 and wait untill LED provides several short ashes.

4. Disconnect power supply.

5. Remove short-circuit from D1 and D2 pins.

6. Power up EW1.

7. Parameters restored to default.

LED

COM

DC+

Fig. No. 1

+12V

EW1

Power supply

DC+ C1 C2 Z1 Z2 COM

Fig. No. 2

USER MANUAL EW1 V1.0 3

5. Additional Information

Limited Liability

The buyer must agree that the system will reduce the risk of re, theft, burglary or other dangers but does not guarantee against such

events.“ELDES UAB”will not take any responsibility regarding personal or property or revenue loss while using the system.

“ELDES UAB”liability according to local laws does not exceed value of the purchased system.“ELDES UAB”is not aliated with any of

the Internet providers therefore is not responsible for the quality of Internet service.

Manufacturer Warranty

This device carries a 24-month warranty by the manufacturer“ELDES UAB”. Warranty period starts from the day the system has been

purchased by the end user. The warranty is valid only if the system has been used as intended, following all guidelines listed in the

manual and within specied operating conditions. Receipt must be kept as a proof of purchase date. The warranty is voided if the

system has been exposed to mechanical impact, chemicals, high humidity, uids, corrosive and hazardous environment or other

force majeure factors.

Safety instructions

Please read and follow these safety guidelines in order to maintain safety of operators and people around:

• DO NOT use the system where it can be interfere with other devices and cause any potential danger.

• DO NOT use the system with medical devices.

• DO NOT use the system in hazardous environment.

• DO NOT expose the system to high humidity, chemical environment or mechanical impacts.

• DO NOT attempt to personally repair the system.

EW1 must be powered by 7-15V 20mA max. DC power supply which must be approved by LST EN 60950-1 standard and be

easily accessible nearby the device.When connecting the power supply to EW1, switching the pole terminals places is forbidden.

Any additional devices linked to EW1 (electrical appliances, relays etc.) must be approved by LST EN 60950-1 standard.

EW1 is fully turned o by disconnecting 2-pole switch device of the external power supply or any other linked device that EW1

is powered from.

The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates

that the product must not be disposed of together with household waste. To prevent possible harm to human health

and/or the environment, the product must be disposed on in an approved and environmentally safe recycling process.

For further information on how to dispose of this product correctly, contact the system supplier, or the local authority

responsible for waste disposal in your area.

It is not allowed to copy and distribute information in this document or pass to a third party without advanced written

authorization by“ELDES UAB”.“ELSDES UAB”reserves the right to update or modify this document and/or related products

without a warning. Hereby, ELDES UAB declares that this wireless zone & PGM output expansion module EW1 is in com-

pliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity

may be consulted at www.eldes.lt

Andere Eldes Computerhardware Handbücher

Eldes

Eldes ESIM252 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung