EldoLED SOLOdrive 560/S Kurzanleitung

Pay attention when connecting the LED groups:

polarity reversal results in no light output and often damages the LEDs.

More documentation and eldoLED’s terms and conditions are available at www.eldoled.com.

{

120-277 VAC

9 mm

0.35 inch

0.5-1.5 mm

AWG 20-16

DALI

LEDcode / NTC

2 LED groups

(1 ballast)

Wiring diagram SOLOdrive 560/S (SL0560S1)

WARNING: Risk of electrical shock. May result in serious injury or death. Disconnect power before servicing or installing.

CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and build-

ing codes must be observed. Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.

LED group

Indicates the location of the connectors for your LED groups. These

LED groups represent one DALI ballast.

LED wiring distance

Maximum wiring distance at full load:

LEDcode/NTC

LEDcode allows configuration of

• Dimming curve: lin / log

• Minimum dimming level

• NTC throttle temperature

• LED drive current per output: from 200mA-1,050mA in 1mA steps

Programming the driver via LEDcode requires a TOOLbox pro and

FluxTool software.

Connecting a 47kΩNTC thermistor enables closed loop thermal

control. The NTC throttle temperature is programmable through

LEDcode.

DALI

You can use these connectors to connect the driver to a DALI network.

Always combine a DA+ and DA- connector for either data input or data

output.

120-277 VAC

The driver has been designed for use with universal mains voltage in-

put of 120-277 VAC, 50/60Hz.

AWG value 20 19 18 17 16

Distance(m)1418222836

Distance (ft) 45.9 59 72.2 91.9 118.1

Please observe voltage drop over long cable lengths.

Longer cable lengths increase EMI susceptibility.

eldoLED Europe bv Luchthavenweg 18a 5657 EB Eindhoven The Netherlands T +31 40 2054050 F +31 40 2054058 [email protected]

eldoLED America, Inc. 1762 Technology Drive # 226 San Jose, CA95110 USA T +1 408 451 9333 F +1 408 451 9335 nasales@eldoled.com

Wiring diagram SOLOdrive 560/S (SL0560S1)

Connecting 1 LED group

Group 1

Group 2

LEDcode

NTC

120-277VAC

50-60Hz

Dieses Handbuch passt für folgende Modelle

Andere eldoLED Gleichstromantrieb Handbücher

eldoLED

eldoLED LINEARdrive 180 Kurzanleitung

eldoLED

eldoLED POWERdrive 561/M Kurzanleitung

eldoLED

eldoLED LINEARdrive 720D Bedienungsanleitung

eldoLED

eldoLED POWERdrive 562/S Bedienungsanleitung

eldoLED

eldoLED LINEARdrive 720D Bedienungsanleitung

eldoLED

eldoLED POWERdrive 106/S Kurzanleitung

eldoLED

eldoLED POWERdrive 45D Kurzanleitung

eldoLED

eldoLED ECOdrive Series Bedienungsanleitung

eldoLED

eldoLED LINEARdrive 720D Kurzanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

eldoLED SOLOdrive 560/S Kurzanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken