Elecro Engineering H.R.UV-C Montageanleitung

H.R.UV-C

Installation & Operating Manual

HR-55

HRP-55

HR-110

HRP-110

www.elecro.co.uk

Important Notes

Congratulations on purchasing the H.R.UV-C pool sanitising system,

the latest in UV technology, manufactured in England to the highest

standards.

To ensure your new product will give years of trouble free service please

carefully read the following instructions.

Incorrect installation will aect your warranty. Do not discard this

manual, please retain for future reference.

Important safety information

•Consult a qualied electrician

•Never look directly at an illuminated UV lamp

• Do not run this unit dry, do not cover this unit

• Always isolate the unit from mains electricity and turn o the water

supply before carrying out maintenance

• Always disconnect all pool appliances from the mains electricity supply

before servicing

• Power must be supplied through a Residual Current Device (RCD) with

a rated residual operating current not exceeding 30mA

• This unit must be earthed. Never use a higher rated fuse than specied

• The unit must not be submerged in water

• If the quartz sleeve is cracked, replace it immediately

•Young children should always be supervised near water

Specication

Model: HR-55 & HR-110 (Analogue); HRP-55 & HRP-110 (Digital)

Rating: 220~240V 50/60Hz; 110~120V 50/60Hz

MAX Pressure = 3 Bar

This unit is manufactured in conformance with:

Safety: BS EN 60335-1:2002. BS EN 60335-2-55:2003

EMC: EN 55015: 2000. EN 61000-3-2: 2000 EN 61000-3-3: 1995.

EN61547:1995

This unit is CE approved.

www.elecro.co.uk

ENGLISH

Product Overview

The H.R.UV-C is available in 55W single tube and 110W double tube

formats, supplied complete with ow switch and either an analogue

lamp life indicator and reset switch, or digital lamp life countdown with

intelligent dosing pump.

Fig 1.

55W Single Tube Unit

Note: Digital Model Shown

www.elecro.co.uk

ENGLISH

Fig 2.

110W Double Tube Unit

Note: Digital Model Shown

www.elecro.co.uk

Positioning the Unit

CAUTION: To prevent this unit falling into water, do not install above

or alongside your pool.

The H.R.UV-C unit is weatherproof but not waterproof; it must be installed

in a dry weatherproof enclosure. The unit must be mounted on a at

vertical surface horizontally or vertically. It must not be submerged in

water or placed in a position where water may collect around the unit.

To prevent the unit inadvertently being dropped into the pool, the unit

must be installed at least 3.5 metres from the edge of the pool.

The unit must always be plumbed into the water system after the lter as

shown in g 3. to prevent dirt and debris being pumped into the unit.

Fig 3.

ENGLISH

5www.elecro.co.uk

ENGLISH

Mounting the UV Unit

The unit may be mounted on a wall or other suitable vertical surface that

is structurally strong enough (for example: when full of water the unit is

too heavy to mount onto a conventional wooden fence panel). The unit is

supplied with a xing kit. The unit can be mounted vertically as shown in

the next pages in g 5. and 6. or horizontally as shown in g 7.

NOTE!

When mounting the UV it is essential to leave a clearance space of at least 1

metre from one side of the unit to allow access to replace the lamp(s) and/or

quartz sleeve(s) when required. Both the lamps and the quartz sleeve can be

replaced from either end of the unit; if installing vertically the 1 metre clearance

space must be above or below the unit, if installing horizontally the 1m

clearance space must be to the left or right of the unit.

ENGLISH

Fig.4

www.elecro.co.uk

ENGLISH

Washer x4

Screw x4

Raw plug x5

Fig 5.

55W Single Tube Unit

www.elecro.co.uk

Fig 6.

110W Double Tube Unit

Washer x5

Raw plug x5

Screw x5

2www.elecro.co.uk 8

Fig 7.

ENGLISH

Vertical

mounting

110W Double Tube Unit

Horizontal mounting

55W Single Tube Unit

Horizontal mounting

Water must enter low

and exit high

Water must enter low

and exit high

Factory Default

Optional reverse ow

explained on page 10

Factory Default

Optional reverse ow

explained on page 10

Mounting Continued

Vertical

mounting

www.elecro.co.uk

Connection to the water supply

The unit is supplied with unions to allow connection to 2" or 63-mm rigid

pipe. Reducers are also supplied to allow connection to 50-mm or 1½" rigid

pipe - see g. 8.

For connection to 63-mm or 2" diameter pipe

Insert 63-mm

diameter pipe up

to this stop

Insert 2" diameter

pipe up to this

stop

ADHESIVE

ABS

PVC ×

Insert 50-mm

diameter pipe up

to this stop

Insert 1½"

diameter pipe up

to this stop

Solvent weld your

pipe to the correct

stop

Solvent weld the

supplied reducer

into the union

NOTE!

ADHESIVE

ABS

PVC ×

NOTE!

Fig 8.

For connection to 50-mm or 1½" diameter pipe

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Elecro Engineering Wasserfiltersystem Handbücher

Elecro Engineering

Elecro Engineering Spectrum Hybrid SH-55 Montageanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung