Electro-Harmonix Epitome Bedienungsanleitung

EPITOME

MULTI-EFFECT PEDAL featuring

MICRO POG, STEREO ELECTRIC

MISTRESS, & HOLY GRAIL PLUS

Congratulations on your purchase of the Electro-Harmonix Epitome multi-effect

pedal. The Epitome combines three of the most popular and advanced Electro-

Harmonix pedals: the Micro POG octave generator, the Stereo Electric Mistress

flanger/chorus pedal, and the Holy Grail Plus reverb unit.

The effects on the Epitome can function independently, together, or can interact

with each other in a unique manner by engaging SHIMMER mode. The three

separate footswitches, one for each section, allow for individual control over

which effect is on or off. Each effect has its own dedicated knobs and switches,

all of which are tweakable at any moment; there are no menus or hidden

settings to scroll through.

Shimmer mode reroutes the Epitome’s effects in a way that would not be

possible with the three separate effects pedals. In Shimmer mode, the octaves

from the Micro POG are separated from the Dry signal allowing the Holy Grail

Plus to only reverberate the octaves. Additionally, Flerb mode in the Holy Grail

Plus changes to an echo effect, where the Micro POG is placed in the feedback

path of the delay to create echoes that change octaves with each repeat.

Using the Epitome is like having three separate effects pedals on your

pedalboard, without the need for additional cables or separate power supplies,

all in the footprint of one medium sized pedal. The Epitome’s footprint is 5.75” x

4.75”.

WARNING: Your Epitome comes equipped with an Electro-Harmonix

9.6DC-200BI power supply (same as used by Boss®& Ibanez®: 9.6

Volts DC 200mA). The Epitome requires 185mA at 9VDC with a center

negative plug. The Epitome does not take batteries. Using the wrong

adapter may damage your unit and void the warranty.

- CONTROLS, INDICATORS, & I/O -

MICRO POG SECTION

DRY Knob - Controls the output volume of the DRY signal. The DRY signal is

the signal present at the INPUT jack. As this knob is turned clockwise, the

volume of the DRY signal increases. If the Holy Grail Plus is set to ECHO Mode,

the DRY knob sets the delay’s feedback for the dry signal. See page 5 for more

info on the ECHO mode.

SUB OCTAVE Knob - Controls the output volume of the SUB OCTAVE signal.

The SUB OCTAVE signal is one octave below the original input signal, half the

frequency of the input signal. As this knob is rotated clockwise, the volume of

the SUB OCTAVE signal will increase. If the Holy Grail Plus is set to ECHO Mode,

the SUB OCTAVE knob sets the delay’s feedback for the SUB Octave signal. See

page 5 for more info on the ECHO mode.

OCTAVE UP Knob - Controls the output volume of the OCTAVE UP signal. The

OCTAVE UP signal is one octave above the original input signal or twice the

frequency of the original input signal. The volume of the OCTAVE UP signal

increases as this knob is rotated clockwise. If the Holy Grail Plus is set to ECHO

Mode, the OCTAVE UP knob sets the delay’s feedback for the upper octave

signal. See page 5 for more info on the ECHO mode.

STEREO ELECTRIC MISTRESS SECTION

RATE Knob - This knob controls the speed or rate of the LFO signal that

modulates the flanger. It also controls the rate of the Chorus effect. Turning the

RATE knob clockwise increases the rate of modulation. When the RATE knob is

turned down, between fully counter-clockwise and the 10 o’clock position, the

Stereo Electric Mistress will enter Filter Matrix mode. In Filter Matrix mode the

LFO signal is disconnected from the Flanger and Chorus so that you can

manually modulate the Flanger/Chorus by turning the RATE knob. Keep the

RATE knob below 10 o’clock to keep it in Filter Matrix mode.

FLANGER Depth Knob - Controls the amount of Flange that is mixed with the

direct signal. The more you turn the knob clockwise, the more pronounced the

flanger effect will be. Turning the FLANGER knob down completely bypasses the

flanger.

CHORUS Depth Knob - Controls the amount of the chorus sound. The more

you turn the knob clockwise, the more pronounced the chorus effect will be.

Turn the CHORUS knob down completely to bypass the chorus effect.

Hint - The Flanger and Chorus effect can be used together. While each individual effect

produces rich sweeping textures, together they can produce dramatically different and

warm soundscapes that are not available when one effect is used alone. See page 5 for

more information on the Stereo Electric Mistress sounds.

HOLY GRAIL PLUS SECTION

REVERB Switch - Chooses the reverb mode. From top to bottom, the modes

are SPRING, HALL, ROOM and FLERB. When Shimmer is enabled, FLERB mode

changes to an echo effect. See Page 6 for descriptions of each reverb mode.

AMOUNT Knob - The function of the AMOUNT knob changes with each REVERB

mode:

REVERB Mode

AMOUNT Parameter

SPRING

Reverb Time & Spring Time

HALL

Reverb Time

ROOM

Damping Amount

FLERB/Echo

Modulation Rate/Delay Time

BLEND Knob - Controls the wet/dry mix from 100% Dry (counter-clockwise

position) to 100% Wet (clockwise position). Set BLEND to 12 o’clock for an equal

mix of both.

SHIMMER Switch - Enables SHIMMER mode, which changes the routing

between each effect to produce a lush, shimmering reverb tone while keeping a

dry initial attack. See pages 4-5 for details on SHIMMER mode. When SHIMMER

mode is enabled, the Holy Grail Plus LED lights up green. If SHIMMER is

disabled, the Holy Grail Plus LED will be red.

FOOTSWITCHES & LEDs

Each effect section of the Epitome has its own independent footswitch to toggle

the associated effect in and out of bypass. Bypass through the Epitome is

buffered bypass.

MICRO POG Footswitch and STATUS LED –The footswitch located nearest

to the IN jack toggles the Micro POG effect on or off. When the LED in the Micro

POG section is lit, the Micro POG effect is active. When the Micro POG LED is off,

the Micro POG section is bypassed.

STEREO ELECTRIC MISTRESS Footswitch and STATUS LED –The

footswitch located in the middle of the Epitome toggles the Stereo Electric

Mistress effect on or off. When the LED in the Stereo Electric Mistress section is

lit, the Stereo Electric Mistress effect is active. When the Stereo Electric Mistress

LED is off, the Stereo Electric Mistress section is bypassed. When lit, the Stereo

Electric Mistress LED fades between red and green to show the rate of

modulation.

HOLY GRAIL PLUS Footswitch and STATUS LED –The footswitch located

nearest the OUT jack of the Epitome toggles the Holy Grail Plus effect on or off.

When the LED in the Holy Grail Plus section is lit (either red or green), the Holy

Grail Plus effect is active. When the Holy Grail Plus LED is off, the Holy Grail Plus

section is bypassed. A red LED in the Holy Grail Plus section indicates that the

SHIMMER setting is off. A green LED in the Holy Grail Plus section indicates that

the SHIMMER setting is on. More information on the operation of the SHIMMER

switch is on pages 4-5.

I/O & POWER JACKS

MONO/L and R INPUT Jacks - The Epitome allows for full stereo input. The

input jacks are labeled: Mono/L and R. When using the Epitome with only one

input we suggest you use the MONO/L input. When using a single input, the

input impedance is 500k. When using both inputs, the input impedance at each

jack is 1M.

MONO/L Output Jack - This 1/4” jack is the main effect output jack when

connected in mono and the Left output when hooked up in stereo. The output

impedance at this jack is 910.

R Output Jack - This 1/4” jack is the Right effect output jack. Connect this jack

to your second amp or second mixer channel when connecting the Epitome in

stereo. The output impedance at this jack is 910.

9V Power Jack - Connect the output plug from the AC Adapter that was

supplied with your Epitome to this jack, located at the top of the unit. The

Epitome requires 185mA at 9VDC. The polarity of the power jack is center

negative.

- STEREO OPERATION AND THE SHIMMER SWITCH -

The Epitome can be used either as a mono or stereo effect unit. Signal routing in

the Epitome depends on which effects are engaged, and the position of the

SHIMMER switch.

SHIMMER Switch Off –With the SHIMMER switch off, the effects in the

Epitome work independently, in the following order:

IN MICROPOG STEREO ELECTRIC MISTRESS HOLY GRAIL PLUS OUT

The Micro POG section is a mono effect. If both the L and R inputs are being

used, the L and R signals are combined before going through the Micro POG

octave section, while the DRY signal remains stereo through the Micro POG.

When the Micro POG is bypassed, L and R inputs remain separate.

The Stereo Electric Mistress section is stereo. The Stereo Electric Mistress will

produce separate stereo flange/chorus sounds whether it is fed by a stereo

signal or a mono signal (such as a single guitar or the output of the Micro POG).

The Holy Grail Plus section has a mono input but a stereo output. If the Holy

Grail Plus is being fed by a stereo signal (such as the output of the Stereo

Electric Mistress or the L and R inputs), the L and R signals are combined before

entering the Holy Grail Plus reverb block but the DRY signal remain in stereo.

The output of the reverb effect is stereo. When the Holy Grail Plus is bypassed, L

and R inputs remain separate.

SHIMMER Switch On –With the SHIMMER switch engaged, the effects

interact to produce sounds unique to the Epitome pedal. The signal path is

rearranged in the following manner:

IN MICROPOG HOLY GRAIL PLUS STEREO ELECTRIC MISTRESS OUT

Normal SHIMMER Mode –The Epitome is in normal SHIMMER mode when

the SHIMMER switch is on, both the Micro POG and Holy Grail Plus are engaged,

and the Holy Grail Plus is set to SPRING/HALL/ROOM. In this setting, the Holy

Grail Plus only applies reverb to the octave signals from the Micro POG. The

BLEND knob controls the balance between the separated dry signal and the

reverberated octave signals.

ECHO Mode (Shimmer engaged, set to FLERB) –The Holy Grail Plus functions

as a delay pedal when SHIMMER is enabled, the Holy Grail Plus section is on,

and the Holy Grail Plus is set to FLERB. In this mode, the AMT knob controls

the delay time, ranging from 25ms to 590ms. If the Micro POG section is

off, the delay will produce only one repeat. If the Micro POG section is engaged,

then the knobs on the Micro POG control the delay’s feedback for each of their

associated octaves, allowing for each echo repeat to go through the octave

effects. As an example, if the OCTAVE UP knob is turned to 2 o’clock and you

play a C2 note, each echo will go up one octave to C3, C4, C5, etc.

- STEREO ELECTRIC MISTRESS EFFECT DESCRIPTIONS -

FLANGER Effect - The flanging effect can be thought of as a pitch slowly

sweeping between high and low limits superimposed on the guitar signal. The

RATE control allows you to change the speed at which the sweep occurs. With

the RATE control fully counter-clockwise, you enter the Filter Matrix mode, which

extends to the 10’o'clock position of the knob. Turning the dial clockwise

increases the rate to the point where the frequency of the input signal appears

to be shifted in a vibrato-like fashion. The Chorus effect follows the same

principle but produces a lush chorus where the rate control is identically applied

to the Chorus and Flanger.

FILTER MATRIX Mode - The Stereo Electric Mistress has been set at the

factory for maximum color capacity in the FLANGER mode. One of the unique

settings inherited from the legendary Deluxe Electric Mistress is the Filter Matrix

mode. The harmonic makeup of the flange remains while no frequency

modulation is applied. Different tonalities can be obtained when the RATE knob

is set between a totally off position to around 10 o’clock position.

- HOLY GRAIL EFFECT DESCRIPTIONS -

SPRING Reverb - The Spring Reverb effect is a simulation of the spring reverb

found in many classic guitar amps. In SPRING mode, the AMOUNT knob controls

the size of the spring reverb. The further you turn the AMOUNT knob clockwise,

the bigger the spring reverb will be. Set the AMOUNT knob to 12 o’clock to

obtain the Spring Reverb found in the Holy Grail.

HALL Reverb - Hall Reverb is a simulation of the reverb heard in a large space

In HALL mode, the AMOUNT knob controls the reverb time. The further you turn

the AMOUNT knob clockwise, the longer the reverb time and the larger the

reverb space. Using the AMOUNT control you can obtain reverb spaces from a

room to a large hall. To obtain the Hall Reverb sound found in the Holy Grail,

turn the AMOUNT knob to 1 o’clock.

ROOM Reverb - Room Reverb is a simulation of the reverb heard in a small

space. In ROOM mode, the AMOUNT knob controls the damping factor of the

reverb. As the AMOUNT knob is turned clockwise, the reverb will be less

damped. Set the AMOUNT knob to its minimum position (full counter-clockwise)

and the reverb will be heavily damped, sounding like a bathtub reverb. Turn the

AMOUNT knob to full clockwise and the reverb sounds like an open room with no

damping.

FLERB Reverb - The Flerb Reverb effect is made up of a reverb followed in

series by a flanger. In FLERB mode, the AMOUNT knob controls the rate of the

Flerb’s modulation. As you turn AMOUNT clockwise, the rate of modulation

increases. To obtain the Flerb sound found in the Holy Grail, turn the AMOUNT

knob to 8 o’clock.

ECHO (Shimmer engaged, set to FLERB) –The Echo effect plays back a delayed

copy of the input signal. In ECHO mode, the AMOUNT knob controls the delay

time, ranging from 25ms to 590ms. The Micro POG’s knobs control the delay’s

feedback for each individual octave when the Micro POG is engaged. If the Micro

POG is not engaged, the echo effect will have just one repeat. As feedback is

increased on any octave, the Echo produces more repeats of that octave with

each cycle through the delay line going up or down an octave.

- SAMPLE SETTINGS: SHIMMER OFF -

12 String Guitar

OFF

Old Radio

OFF

Huge Hall

OFF

- SAMPLE SETTINGS: SHIMMER ON -

Lush Chord Reverb

OFF

Subtle Ambience Reverb

OFF

Fast Echo

OFF

- SAMPLE SETTINGS: SHIMMER ON -

Fluttering Echoes

OFF

Octave Echo Multiplicity

OFF

Bass Follower

OFF

- USER SETTINGS -

Use this page to record your favorite settings

Inhaltsverzeichnis

Andere Electro-Harmonix Musikpedal Handbücher

Electro-Harmonix

Electro-Harmonix nano STEEL LEATHER Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix HELL MELTER Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Andy Summers Walking On The Moon Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Superego+ Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix OPERATION OVERLORD Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix SLAMMI Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix KEY9 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix nano SMALL STONE Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix NEO MISTRESS Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix SOUL FOOD Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Grand Canyon Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Super Switcher Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Intelligent Harmony Machine Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Memory Boy Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix MEL9 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix BAD STONE Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix 1 ECHO Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix 8-STEP PROGRAM FOOT CONTROLLER Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Holier Grail Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Pitch Fork Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix LUMBERJACK Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix EDDY Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix Pitch Fork+ Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix METAL MUFF with TOP BOOST Bedienungsanleitung

Beliebte Musikpedal Handbücher anderer Marken

Behringer

Behringer ULTRA WAH UW300 Bedienungsanleitung

Whirlwind

Whirlwind oc-bass Bedienungsanleitung

Strymon

Strymon Lex-rotary Bedienungsanleitung

Behringer

Behringer PB600 Bedienungsanleitung

Lexicon

Lexicon MX200 Bedienungsanleitung

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Bedienungsanleitung

Matthews Effects

Matthews Effects Whaler V2 Bedienungsanleitung

Grid 1

Grid 1 Pedal Jeanie Bedienungsanleitung

Amptweaker

Amptweaker tightboost Bedienungsanleitung

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Bedienungsanleitung

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER Bedienungsanleitung

BYOC

BYOC Analog Chorus Handbuch

Dimavery

Dimavery EPVP-50 Bedienungsanleitung

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Bedienungsanleitung

Pro-MIDI

Pro-MIDI G25 Bedienungsanleitung

DW 7000 Bedienungsanleitung

FAMC

FAMC Liquid-Foot Jr. Series Bedienungsanleitung

Dimavery

Dimavery EPOD-50 Overdrive Bedienungsanleitung