Electrolux Professional ZPPWES Bedienungsanleitung

ENGLISH

A SAFETY INSTRUCTIONS ................................................................................ Page 6

B GENERAL INFORMATION .............................................................................. Page 7

B1 Introduction ...................................................................................................................... Page 7

B2 Definitions........................................................................................................................ Page 7

B3 Typographical conventions .............................................................................................. Page 7

B4 Machine and Manufacturer’s identification data............................................................... Page 8

B5 Equipment identification .................................................................................................. Page8

B5.1 How to identify the technical data........................................................................ Page 8

B5.2 How to interpret the factory description............................................................... Page 8

B6 Copyright ......................................................................................................................... Page 9

B7 Liability............................................................................................................................. Page 9

B8 Personal protection equipment ........................................................................................ Page 9

B9 Keeping the manual......................................................................................................... Page 9

B10 Users of the manual ........................................................................................................ Page 9

C GENERAL DESCRIPTION OF MACHINE ....................................................... Page 10

C1 General description ......................................................................................................... Page 10

D TECHNICAL DATA ........................................................................................... Page 10

D1 Main technical characteristics.......................................................................................... Page 10

D2 Characteristics of power supply....................................................................................... Page 11

E TRANSPORT, HANDLING AND STORAGE.................................................... Page 12

E1 Introduction...................................................................................................................... Page 12

E1.1 Transport: Instructions for the carrier................................................................... Page 12

E2 Handling .......................................................................................................................... Page 12

E2.1 Procedures for handling operations..................................................................... Page 12

E2.2 Translation ........................................................................................................... Page 12

E2.3 Placing the load ................................................................................................... Page 12

E3 Storage ............................................................................................................................ Page 12

F INSTALLATION AND ASSEMBLY ................................................................... Page 13

F1 Customer responsibilities ................................................................................................ Page 13

F2 Characteristics of the place of machine installation......................................................... Page 13

F3 Machine space limits ....................................................................................................... Page 13

F4 Positioning ....................................................................................................................... Page 13

F5 Disposal of packing ......................................................................................................... Page 14

F6 Plumbing connections ..................................................................................................... Page 14

F6.1 Plumbing circuits ................................................................................................. Page 15

F6.2 Installation diagrams............................................................................................ Page 16

F7 Electrical connections...................................................................................................... Page 20

F8 Energy control arrangement ............................................................................................ Page 21

F9 HACCP arrangement....................................................................................................... Page 21

G DESCRIPTION OF CONTROL PANEL ............................................................ Page 22

G1 Basic controls .................................................................................................................. Page 22

H STARTING ........................................................................................................ Page 23

EN INDEX

H1 Preliminary checks, adjustments and operational tests ...................................................Page 23

H1.1 Electrical and plumbing checks ...........................................................................Page 23

H1.2 Check the positioning of tank components ..........................................................Page 23

H1.2.1 Check the fitting of filters ................................................................... Page 23

H1.2.2 Arm fitting check................................................................................ Page 23

H2 Starting ............................................................................................................................Page 23

H3 Detergent/rinse-aid dispensers and settings ...................................................................Page 23

H4 Setting the dispensers ..................................................................................................... Page 24

I GENERAL SAFETY RULES.............................................................................Page 26

I1 Introduction ......................................................................................................................Page 26

I1.1 Protection devices installed on the machine........................................................Page 26

I1.1.1 Guards ..............................................................................................Page 26

I1.2 Safety signs to be displayed on the machine or near the work area ................... Page 26

I2 Decommissioning ............................................................................................................Page 26

I3 Instructions for use and maintenance..............................................................................Page 26

I4 Improper use....................................................................................................................Page 27

I5 Residual risks ..................................................................................................................Page 27

J NORMAL MACHINE USE.................................................................................Page 28

J1 Correct use ...................................................................................................................... Page 28

J2 Characteristics of personnel enabled to operate on the machine....................................Page 28

J3 First use ........................................................................................................................... Page 28

J4 Daily activation of machine ..............................................................................................Page 28

J5 Wash cycles.....................................................................................................................Page 28

J6 Operation .........................................................................................................................Page 29

J7 Alarms .............................................................................................................................Page 30

J8 Machine cleaning.............................................................................................................Page 30

J8.1 End of service and daily internal cleaning ...........................................................Page 30

J8.2 Exterior cleaning..................................................................................................Page 32

J9 Long idle periods .............................................................................................................Page 32

J10 Maintenance ....................................................................................................................Page 32

J10.1 Preventive maintenance ...................................................................................... Page 32

J11 Machine disposal .............................................................................................................Page 33

J12 Troubleshooting ...............................................................................................................Page 33

ENGLISH

INDEX OF FIGURES

Figure 1 Reproduction of the marking/dataplate on the machine..................................................... Page 8

Figure 2 Position of marking............................................................................................................. Page 8

Figure 3 Technical data identification ............................................................................................... Page 8

Figure 4 Example of document identification data. .......................................................................... Page 9

Figure 5 Unpacking .......................................................................................................................... Page 13

Figure 6 Machine positioning ........................................................................................................... Page 13

Figure 7 Removal of wooden spacers.............................................................................................. Page 13

Figure 8 Removing the film ..............................................................................................................Page 14

Figure 9 Feet adjustment ................................................................................................................. Page 14

Figure 10 Feed pipe connection......................................................................................................... Page 14

Figure 11 380-415 V 3N..................................................................................................................... Page 21

Figure 12 400-440V 3 ........................................................................................................................ Page 21

Figure 13 220-230V 3 ........................................................................................................................ Page 21

Figure 14 Energy control .................................................................................................................... Page 21

Figure 15 Tank filters .......................................................................................................................... Page 23

Figure 16 Wash and rinse arms ......................................................................................................... Page 23

Figure 17 Automatic dispenser arrangement ..................................................................................... Page 24

Figure 18 Detergent dispenser terminal block.................................................................................... Page 24

Figure 19 Rinse aid dispenser terminal block .................................................................................... Page 24

Figure 20 Wash water pressure adjustment....................................................................................... Page 29

Figure 21 Basket for pans .................................................................................................................. Page 30

Figure 22 Tray rack............................................................................................................................. Page 30

Figure 23 Release the door................................................................................................................ Page 30

Figure 24 Tank filters .......................................................................................................................... Page 31

Figure 25 Refit the door ..................................................................................................................... Page 31

Figure 26 Rotating wash arms and rinse arms .................................................................................. Page 31

Figure 27 Fixed wash arm removal .................................................................................................... Page31

Figure 28 Fixed wash arm cleaning ................................................................................................... Page32

INDEX OF TABLES

Ta b l e 1 Main technical characteristics, performance and consumption.......................................... Page 10

Ta b l e 2 Control panel...................................................................................................................... Page 22

Ta b l e 3 Residual risks..................................................................................................................... Page 27

EN INDEX OF FIGURES AND TABLES

Foreword

The instruction manual (hereinafter Manual) provides the operator with useful information for working correctly and

safely, facilitating him in using the machine (hereinafter “machine”, “dishwasher” or “equipment”).

The following must not be considered a long and exacting list of warnings, but rather a set of instructions suitable for

improving machine performance in every respect and, above all, preventing injury to persons and animals and dam-

age to property due to improper operating procedures.

All persons involved in machine transport, installation, starting, use and maintenance, repair and dismantling must

consult and carefully read this manual before performing the various operations, for the purpose of avoiding wrong

and improper actions that could negatively affect the machine’s integrity or endanger persons.

The manual must always be available to operators and carefully kept in the place where the machine is used so that

it is immediately at hand for consultation in case of doubts or whenever required.

If, after reading this manual, there are still doubts regarding machine use, do not hesitate to contact the Manufac-

turer, or the authorized assistance centre, to receive prompt and precise assistance for better operation and maxi-

mum efficiency of the machine.

During all phases of machine use, always respect the current regulations on safety, work hygiene and environmental

protection. It is the user’s responsibility to make sure the machine is started and operated only in optimal safety con-

ditions for persons, animals and property.

A SAFETY INSTRUCTIONS

• This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning use of the appliance in a

safe way and understand the hazards involved.

• Do not let children play with the appliance.

• Cleaning and user maintenance shall not be made by children without supervision.

WARNING

Do not wash the appliance with direct or high pressure jets of water.

ENGLISH

BGENERAL INFORMATION

B1 Introduction

This chapter describes the symbols used (that mark

and identify the type of warning) and gives the defini-

tions of terms used in the manual, responsibilities and

B2 Definitions

Listed below are the definitions of the main terms used

in the Manual. Carefully read them before using the

Manual.

Operator

an operator who carries out machine installation,

adjustment, use, maintenance, cleaning, repair and

transport.

Manufacturer

Electrolux Professional S.p.A. or any other assistance

centre authorized by Electrolux Professional S.p.A..

Operator qualified for normal machine use

an operator who has been informed, instructed and

trained regarding the tasks and hazards involved in

normal machine use.

Specialized technician or Technical assistance

an operator instructed/trained by the Manufacturer and

who, based on his professional and specific training,

experience and knowledge of the accident-prevention

regulations, is able to appraise the operations to be

carried out on the machine and recognize and prevent

possible risks. His professionalism covers the mechan-

ical, electrotechnical and electronics fields.

Danger

source of possible injury or harm to health.

Hazardous situation

any situation where an operator is exposed to one or

more hazards.

Risk

a combination of probabilities and risks of injury or

harm to health in a hazardous situation.

Guards

safety measures consisting of the use of specific tech-

nical means (guards and safety devices) for protecting

operators against dangers.

Guard

an element of a machine used specifically to provide

protection by means of a physical barrier.

Safety device

a device (other than a guard) that eliminates or

reduces the risk; it can be used alone or in combina-

tion with a guard.

Customer

the person who purchased the machine and/or who

manages and uses it (e.g. company, entrepreneur,

firm).

Emergency stop device

a group of components intended for the emergency

stop function; the device is activated with a single

action and prevents or reduces damage to persons/

machines/property/animals.

Electrocution

an accidental discharge of electric current on a human

body.

B3 Typographical conventions

For best use of the manual, and therefore the machine,

it is advisable to have good knowledge of the terms

and typographical conventions used in the documenta-

tion.

The following symbols are used in the manual to mark

and identify the various types of hazards:

Machine guards and protection devices marked with

this symbol must only be opened by qualified person-

nel, after disconnecting the power to the machine.

Words and safety warnings further explaining the type

of hazard are placed next to the symbols in the text.

The warnings are intended to guarantee the safety of

personnel and prevent damage to the machine or the

product being worked.

The drawings and diagrams given in the manual are

not in scale. They supplement the written information

with an outline, but are not intended to be a detailed

representation of the machine supplied.

The numerical values given in the machine installation

diagrams refer to measurements expressed in mm

(see pargraph F6.2 “Installation diagrams”).

WARNING!

DANGER FOR THE HEALTH

AND SAFETY OF OPERATORS.

WARNING!

DANGER OF ELECTROCU-

TION - DANGEROUS VOLTAGE.

WARNING!

DANGER OF DAMAGE TO THE

MACHINE.

B4 Machine and Manufacturer’s identification

data

A reproduction of the marking or dataplate on the

machine is given below.

Figure 1 Reproduction of the marking/dataplate

on the machine.

The dataplate gives the product identification and tech-

nical data; the meaning of the information given on it is

listed below.

F.Mod. .................... factory description of the product

Comm. Model ........ trade description

PNC: ...................... production code number

Ser. Nr. .................. serial number

AC 400V 3N ........... power supply voltage

50 Hz ..................... power supply frequency

20 kW ..................... max. power absorbed

13 kW .....................power absorbed as factory setting

2015 ....................... year of construction

CE .......................... CE marking

IPX5 ....................... protection rating

Electrolux Professional S.p.A.

Viale Treviso, 15

33170 Pordenone

(Italy) ...................... Manufacturer

The marking plate is located on the right side panel of

the equipment.

Figure 2 Position of marking

B5 Equipment identification

B5.1 How to identify the technical data

To identify the technical data (Figure 3) read the fac-

tory description of the product (F.Mod.) on the data-

plate, identify the main machine data and consult the

Table 1 “Main technical characteristics, performance

and consumption”.

Figure 3 Technical data identification

B5.2 How to interpret the factory description

The factory description on the dataplate has the follow-

ing meaning (some examples are given below):

WARNING!

Do not remove, tamper with or

make the machine marking

illegible.

ELX Made in EU 2011

F.Mod. EPPWESG Comm. Model EPPWESG

PNC 9CGX 50604800 Ser.Nr. 22406001

EL AC 400V 3N 50 Hz Max. 20 kW

Nominal. 13kW

Electrolux Professional spa- Viale Treviso, 15 - 33170 Pordenone (Italy)

ELX Made in EU 2011

F.Mod.

EPPWESG

Comm. Model

EPPWESG

PNC 9CGX

506048

00 Ser.Nr.

22406001

EL AC 400V 3N 50 Hz Max. 13 kW

Nominal 20kW

Electrolux Professional spa - Viale Treviso, 15 - 33170 Pordenone (Italy)

IMPORTANT!

Refer to the data given on the machine

marking for relations with the Manufac-

turer (e.g. when ordering spare parts,

etc.).

IMPORTANT!

When disposing of the machine the

marking must be destroyed.

Electric versions

(1) (2) (3) (4) (5) (6) (7)

Z PPW E S G

N PPW E H G

E PPW E L G 60 60

E PPW E S G M 6

Steam versions

(1) (2) (3) (4) (5) (6) (7)

Z PPW S S G

Z PPW S L G

Variables description

(1) Mark Z = Zanussi, N = To brand, E = Electrolux.

(2) Machine type PPW = Pot washer

(3) Supply E = Electric, S = Steam

(4) Model S = small, H = high, L = large

(5)...(7) G = Detergent pump + rinse aid pump + drain pump,

M = Marine, 6-60 = 60 Hz.

ELX Made in EU

F.Mod. EPPWESG

Electrolux Professional spa- Viale Treviso, 15

D1 Main technical characteristics

MODEL EPPWES

Power supply Electric

Power supply voltage V 400 3N

Frequency Hz 50

ENGLISH

B6 Copyright

This manual is intended for consultation only by the

operator and can be given to third parties only with the

written permission of Electrolux Professional S.p.A..

B7 Liability

The instructions are updated to the month and year

given in the box located at the bottom right of the

cover. The edition corresponds to the manual revision

number. Every new edition replaces and cancels the

previous ones.

Figure 4 Example of document identification data.

The Manufacturer declines any liability for damage and

malfunctioning caused by:

• non-compliance with the instructions contained in

this manual;

• repairs not carried out in a workmanlike fashion,

and replacements using spare parts different from

those specified in this manual (the fitting and use of

non-original spare parts and accessories can nega-

tively affect machine operation);

• operations by non-specialized technicians;

• unauthorized modifications or operations;

• inadequate maintenance;

• improper machine use;

• unexpected extraordinary events;

• use of the machine by uninformed and untrained

personnel;

• non-application of the current provisions in the

country of use, concerning safety, hygiene and

health in the workplace.

The Manufacturer declines any liability for damage

caused by arbitrary modifications and conversions car-

ried out by the user or the Customer.

The employer or workplace manager is responsible for

identifying and choosing adequate and suitable per-

sonal protection equipment to be worn by operators, in

compliance with current regulations in the country of

use.

Electrolux Professional S.p.A. declines any liability for

possible inaccuracies contained in the manual, if due

to printing or translation errors.

Any supplements to the instruction manual the Cus-

tomer receives from the Manufacturer must be kept

together with the manual, of which they will form an

integral part.

B8 Personal protection equipment

Give below is a summary table of the Personal Protec-

tion Equipment (PPE) to be used during the various

stages of the machine’s service life.

(*) During Normal use, gloves protect hands from the

contact with chemical substances, water and hot sur-

faces.

Failure to use the personal protection equipment by

operators, specialised technicians or users can involve

exposure to chemical risk and possible damage to

health.

B9 Keeping the manual

The manual must be carefully kept for the entire life of

the machine until decommissioning.

The manual must stay with the machine in case of

transfer, sale, hire, granting of use or leasing.

B10 Users of the manual

This manual is intended for:

• the carrier and handling personnel;

• installation and start-up personnel;

• the employer of machine users and the workplace

manager;

• operators in charge of normal machine use;

• specialized technicians - technical assistance (see

wiring diagram and service manual).

DOC. NO. 5956.68P.03

EDITION: 1 03.2015

Month YearEdition

Number

Document

Stage

Protective

garments

Safety foot-

wear

Gloves Glasses Safety

helmet

Transport X

Handling X

Unpacking X

Assembly X

Normal use X X X (*)

Adjustments X

Routine

cleaning X X (*)

Extraordinar

y cleaning

X X

Maintenance X

Dismantling X

Scrapping X

Key:

X PPE REQUIRED

PPE AVAILABLE OR TO BE USED IF

NECESSARY

PPE NOT REQUIRED

C GENERAL DESCRIPTION OF MACHINE

C1 General description

The dishwasher is suitable for washing dishes, glasses, cups, cutlery, trays, containers and receptacles in plastic

and/or steel used for preparing, cooking and serving; as well as various cooking utensils in ceramic and/or metal.

The machine is designed for the above-mentioned applications. Under no circumstances may the machine be used

for other applications or ways not provided for in this manual.

This equipment has been produced to meet the needs for a better work environment and economical efficiency.

These dishwashers are used in restaurants, cafeterias, cooking centres and large institutions.

The special dish racks, that can be equipped with various inserts, offer practical and easy use for obtaining excellent

washing results. The electronic system enables complete supervision of the washing process. The control panel

also has a display that shows the operating parameters and signals any anomalies.

Systems for scraping and wetting the dishes (e.g. manual prewash spray) and areas for sorting and arranging them

in the racks must be arranged ahead of the dishwasher.

D TECHNICAL DATA

D1 Main technical characteristics

Table 1 Main technical characteristics, performance and consumption

MODELS ZPPWES/

NPPWES/

EPPWES

ZPPWEH/

NPPWEH/

EPPWEH

ZPPWEL/

NPPWEL/

EPPWEL

ZPPWSSG ZPPWSLG

EPPWESGM6

Power supply Electric Electric Electric Steam Steam Electric

Supply voltage: V 400V 3N~(1) 400V 3N~ 400-V

3N~(1)

400V 3N~ 400V 3N~ 440V 3N~

- convertible to V 230V 3~(2) 230V 3~ 230V 3~(2) 230V 3~ 230V 3~

Frequency Hz 50(1) 50 50(1) 50 50 60

Max. power input kW 13/20 (*) 13/20 (*) 17/26 (*) 9,5 5 13/20 (*)

Boiler heating elements kW 10.5 10.5 10.5 10,5 10,5 10.5

Tank heating elements kW 7 7 10.5 7 10,5 7

Steamconsumption kg/h---1734-

Maximumsteamtemperature°C---120120-

Inlet steam relative dynamic

pressure

kPa

[bar]

---100-300

[1,0 - 3,0]

100 - 300

[1,0 - 3,0]

Water supply pressure kPa

[bar]

50 - 700

[0,5 - 7,0]

50 - 700

[0,5 - 7,0]

50 - 700

[0,5 - 7,0]

50 - 700

[0,5 - 7,0]

50 - 700

[0,5 - 7,0]

50 - 700

[0,5 - 7,0]

Water supply temp. °C 50 50 50 50 50 50

Water supply hardness °f/°d/°e 14/8/10 max 14/8/10 max 14/8/10 max 14/8/10 max 14/8/10 max 14/8/10 max

Rinse cycle water consumption l 7 7 12 7 12 7

Boiler capacity l 18 18 18 18 18 18

Tank capacity l 95 95 150 95 150 95

Standard cycle time with water

supply at 50°C

sec. 180-360-

540

180-360-

540

180-360-

540

180-360-

540

180-360-

540

180-360-

540

Noise level for single wash pump dB LpA:74.9dB - KpA:1.5dB(3)

Noise level for double wash pump dB LpA:77.2dB - KpA:1.5dB(3)

Protection rating IPX5 IPX5 IPX5 IPX5 IPX5 IPX5

Net weight Kg 215 240 315 215 315 215

Power supply cable H07RN-F H07RN-F H07RN-F H07RN-F H07RN-F H07RN-F

(*) = If activated by software, coincidence of tank and boiler heating elements.

(1) = 380-400V, 3N~, 60Hz only for models EPPWESG60 and EPPWELG60.

(2) = 220-240V, 3~, 60Hz only for models EPPWESG60 and EPPWELG60.

(3) = The noise emission values have been obtained according to EN ISO 11204.

ENGLISH

Standard cycle time may vary should the inlet water temperature be different from that indicated above.

D2 Characteristics of power supply

The AC power supply to the machine must meet the following conditions:

• max. voltage variation ± 10%

• max. frequency variation ± 1% continuous ± 2% for a short period.

Harmonic distorsion, unbalanced three-phase supply voltage, voltage pulses, interruption, dips and the other electric

characteristics must respect the provisions of point 4.3.2 of Standard EN 60204-1 (IEC 60204-1).

380-415 V 3N 400-440 V 3 220-230 V 3

CSCSCS

5 kW 5X1,5 mm216 A 3P+N - - 4X1,5 mm216A 3P

9,5 kW 5X4 mm232 A 3P+N - - 4X8 mm232A 3P

13 kW 5X4 mm225 A 3P+N 4X4 mm225 A 3P 4X10 mm250A 3P

17 kW 5X6 mm240 A 3P+N 4X6 mm240 A 3P 4X10 mm250A 3P

20 kW 5X6 mm240 A 3P+N 4X6 mm240 A 3P 4X16 mm260A 3P

26 kW 5X10 mm250 A 3P+N 4X10 mm250 A 3P 4X16 mm280A 3P

C = Power supply cable

S = On/Off switch

IMPORTANT!

The machine’s power supply must be protected against overcurrents (short circuits and over-

loads) by fuses or suitable thermal magnetic circuit breakers.

These must be fitted on an omnipolar disconnection system having a contact gap of at least 3 mm.

IMPORTANT!

For protection against indirect contacts (depending on the type of supply provided for and con-

nection of earths to the equipotential protection circuit) refer to point 6.3.3 of EN 60204-1 (IEC

60204-1) with the use of protection devices that ensure automatic cut-off of the supply in case of

isolation fault in the TN or TT systems or, for IT systems, the use of isolation controllers or differ-

ential current protection devices to activate automatic power disconnection (an isolation control-

ler must be provided for indicating a possible first earth fault of a live part, unless a protection

device is supplied for switching off the power in case of a such a fault. This device must activate

an acoustic and/or visual signal which must continue for the entire duration of the fault).

For example: in a TT system, a differential switch with cut-in current (e.g. 30 mA) coordinated

with the earthing system of the building where the machine is located must be installed ahead of

the supply.

IMPORTANT!

Customers are requested to follow these instructions, otherwise the Manufacturer does not guar-

antee the machine for continuous operation and/or against faults.

E TRANSPORT, HANDLING AND STORAGE

E1 Introduction

Transport (i.e. transfer of the machine from one place

to another) and handling (i.e. transfer inside work-

places) must occur with the use of special equipment

of adequate capacity.

The machine must only be transported, handled and

stored by qualified personnel, who must have:

- specific technical training and experience;

- knowledge of the safety regulations and applicable

laws in the relevant sectors;

- knowledge of the general safety provisions;

- the ability to recognize and avoid any possible haz-

ard.

E1.1 Transport: Instructions for the carrier

E2 Handling

Arrange a suitable area with flat floor for machine

unloading and storage operations.

E2.1 Procedures for handling operations

For correct and safe lifting operations:

• use the type of equipment most suitable for charac-

teristics and capacity (e.g. lift trucks or electric pal-

let truck);

• cover sharp edges;

• check the forks and lifting procedures according to

the instructions given on the packing.

Before lifting:

• send all operators to a safe position and prevent

persons from accessing the handling zone;

• make sure the load is stable;

• make sure no material can fall during lifting, and

manoeuvre vertically in order to avoid impacts;

• handle the machine, keeping it at minimum height

from the ground.

E2.2 Translation

The operator must:

• have a general view of the path to be followed;

• stop the manoeuvre in case of hazardous situa-

tions.

E2.3 Placing the load

Before placing the load make sure the path is free and

that the floor is flat and can take the load.

E3 Storage

The machine and/or its parts must be stored and pro-

tected against damp, in a non-aggressive place free of

vibrations and with room temperature of between -

10°C / 14°F and 50°C / 122°F.

The place where the machine is stored must have a

flat support surface in order to avoid any twisting of the

machine or damage to the support feet.

WARNING!

Do not stand under suspended

loads during the loading/

unloading phases. Unauthor-

ized personnel must not

access the work zone.

WARNING!

The machine’s weight alone is

not sufficient to keep it steady.

The transported load can shift:

- when braking;

- when accelerating;

- in corners;

- on particularly rough roads.

WARNING!

For machine lifting, do not use

movable or weak parts such as

casings, electrical raceways,

pneumatic parts, etc., as

anchoring points.

WARNING!

Machine positioning, installa-

tion and disassembly must be

carried out by a specialized

technician.

IMPORTANT!

Do not make modifications to the parts

supplied with the machine. Any miss-

ing or faulty parts must be replaced

with original parts.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Electrolux Professional Waschmaschine Handbücher

Electrolux Professional

Electrolux Professional ESI Bedienungsanleitung

Electrolux Professional

Electrolux Professional Clarus Vibe WH6-7 Bedienungsanleitung

Electrolux Professional

Electrolux Professional WE170V Bedienungsanleitung

Electrolux Professional

Electrolux Professional WB5130H Bedienungsanleitung

Electrolux Professional

Electrolux Professional myPRO XL W1100P Bedienungsanleitung

Electrolux Professional

Electrolux Professional Clarus Vibe WH6-7 Bedienungsanleitung

Electrolux Professional

Electrolux Professional W575N Bedienungsanleitung

Electrolux Professional

Electrolux Professional Lagoon WH6-6 Bedienungsanleitung

Electrolux Professional

Electrolux Professional Wascator FOM71 CLS Bedienungsanleitung

Electrolux Professional

Electrolux Professional WH6-20LAC Bedienungsanleitung

Electrolux Professional

Electrolux Professional WE 170 V Bedienungsanleitung

Electrolux Professional

Electrolux Professional WB6-20 Bedienungsanleitung

Electrolux Professional

Electrolux Professional Wascator FOM71 CLS Bedienungsanleitung

Electrolux Professional

Electrolux Professional WB6-20 Bedienungsanleitung

Electrolux Professional

Electrolux Professional Wascator FOM71 CLS Bedienungsanleitung

Electrolux Professional

Electrolux Professional DOUBLE SKIN XL Bedienungsanleitung

Electrolux Professional

Electrolux Professional Compass Pro WB6-18 Bedienungsanleitung

Electrolux Professional

Electrolux Professional WH5 Bedienungsanleitung

Electrolux Professional

Electrolux Professional Lagoon WH6-6 Bedienungsanleitung

Electrolux Professional

Electrolux Professional WH6-14LAG Bedienungsanleitung

Electrolux Professional

Electrolux Professional WE 170 P Bedienungsanleitung

Electrolux Professional

Electrolux Professional WE170PP Bedienungsanleitung

Electrolux Professional

Electrolux Professional Compass Pro WS6-9 Bedienungsanleitung

Electrolux Professional

Electrolux Professional WB5130H Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

Bosch

Bosch WAN2829BSN Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung