Electrolux KITWSRT Technische Daten

[Type here]

USE AND INSTALLATION MANUAL

SOFTENER MODULE - KITWSRT

Doc. No. xx

Edition 0.1.00 –02/2019

USE AND INSTALLATION MANUAL

All the images and information in this manual belong to ©Electrolux Professional Spa. This document and its

contents cannot be copied or used, in part or as a whole, without the authorisation of Electrolux Professional Spa.

USE AND INSTALLATION MANUAL

EDITIONS OF THIS SERVICE MANUAL

EDITION

DESCRIPTION

DATE

1.0.0

First edition

February 2019

INTRODUCTION

The manual provides the user with useful information for assessing the operation (in total safety, by making

it easy to inspect the system, herein after referred to simply with the term “machine” or “device”).

The following must not be considered as a long and tedious list of warnings, but rather as a series of instructions

to be periodically checked in order to keep the machine running efficiently in the long-term and, above all, to avoid

a succession of machine stoppages resulting from it being operated incorrectly.

It is important that all the maintenance and repair technicians and personnel in charge of dismantling the machine

carefully consult and read this manual before starting the various tasks, in order to prevent incorrect and careless

manoeuvres which could compromise the integrity of the machine or constitute a risk to personal safety.

If, after reading this manual, you have any doubts or uncertainties on how to use the machine, please do not

hesitate to contact the manufacturer or the customer care team that are at your disposal to help ensure that the

machine works correctly and efficiently.

IMPORTANT

The manufacturer declines all responsibility for any operation carried out on the machine that ignores the

indications outlined in this manual.

The manufacturer reserves the right to change the specifications of the equipment covered by this documentation

without prior notice. The manufacturer’s technical bulletins must be used as supplements and annexes to this

manual.

The manufacturer declines all responsibility and will not acknowledge the warranty under any circumstances if

original spare parts, that have been specifically approved by the former, are not used.

Whole or partial reproduction of this manual is forbidden.

This manual can be obtained in digital format, in one of the following ways:

contacting the relevant customer care department;

by downloading the latest and most up-to-date version of this manual and technical bulletins from the website

www.electrolux.com/professional

The manual must always be part of the documentation made available when the machine is being used and must

be readily available for consultation at any time.

USE AND INSTALLATION MANUAL

This manual must be carefully stored for future consultation and is considered an integral part of the

machinery. It must be transferred with the machinery if sold and/or relocated.

MODELS COVERED BY THIS MANUAL

MODEL

DESCRIPTION

TYPE

VOLTAGE

KITWSRT

SOFTENER MODULE

ELECTRIC

230/1N/50Hz

 

 
USE AND INSTALLATION MANUAL
TABLE OF CONTENTS 
GENERAL INFORMATION ................................................................................................................................ 7 
1. PURPOSE AND CONTENTS ...................................................................................................................... 7 
2. SAFETY INFORMATION AND PRECAUTIONS......................................................................................... 7 
2.1. PERSONAL PROTECTIVE EQUIPMENT ............................................................................................ 9 
2.2. GENERAL INFORMATION................................................................................................................... 9 
2.3. RESIDUAL RISKS............................................................................................................................... 10 
3. LABEL........................................................................................................................................................ 11 
3.1. IDENTIFICATION PLATE - COLD WATER MIXER HEAD ................................................................ 12 
3.2. IDENTIFICATION PLATE - HOT WATER MIXER HEAD................................................................... 12 
4. SKID SPECIFICATIONS............................................................................................................................ 13 
4.1. OVERALL EXTERNAL DIMENSIONS................................................................................................ 13 
4.2. GENERAL TECHNICAL CHARACTERISTICS................................................................................... 14 
4.3. TECHNICAL CHARACTERISTICS - COLD WATER MIXING HEADS.............................................. 14 
4.4. BY-PASS VALVE ................................................................................................................................ 15 
4.5. TECHNICAL CHARACTERISTICS - HOT WATER MIXING HEADS................................................. 16 
4.6. GENERAL DIMENSIONS –SALT STORAGE SKID.......................................................................... 17 
4.7. TECHNICAL SPECIFICATIONS......................................................................................................... 17 
INSTALLATION AND START-UP.................................................................................................................... 18 
1. INSTALLATION ......................................................................................................................................... 18 
1.1. INSTALLATION –SALT STORAGE SKID.......................................................................................... 19 
1.2. ELECTRICAL CONNECTIONS........................................................................................................... 20 
2. START-UP ................................................................................................................................................. 21 
2.1. STARTING THE SOFTENERS: COLD WATER PART...................................................................... 21 
2.1.1. AIR VENT .................................................................................................................................................. 21 
2.1.2. CHECK THE BRINE EXTRACTION...................................................................................................... 21 
2.1.3. TURBINE VALVE 255.............................................................................................................................. 21 
2.2. STARTING THE SOFTENERS: HOT WATER PART......................................................................... 23 
2.3. STARTING THE SALT STORAGE SKID............................................................................................ 24 
2.4. PERIODIC REFILLING ....................................................................................................................... 24 
MACHINE DESCRIPTION................................................................................................................................ 25 
1. COLD WATER OPERATING LOGIC ........................................................................................................ 25 
2. HOT WATER OPERATING LOGIC........................................................................................................... 26 
3. OPERATING LOGIC.................................................................................................................................. 28 
4. ROUTINE CHECK PLAN........................................................................................................................... 29 
4.1. PREVENTIVE CHECKS...................................................................................................................... 29 
4.2. ROUTINE CHECKS ............................................................................................................................ 29 
4.3. UNSCHEDULED MAINTENANCE WORK ......................................................................................... 30 
4.4. RECOMMENDATIONS....................................................................................................................... 30 
4.5. CLEANING AND MAINTENANCE...................................................................................................... 30 
CONTROL PANEL .......................................................................................................................................... 31 
1. COLD WATER TIMER PROGRAMMING ................................................................................................. 31 
1.1. TIMER CHARACTERISTICS .............................................................................................................. 31 
1.2. TIMER DISPLAY................................................................................................................................. 32 
1.3. SERVICE INDICATIONS DISPLAY.................................................................................................... 33 
1.4. REGENERATION MODE.................................................................................................................... 34 
1.5. TIMER RESET .................................................................................................................................... 34 
1.6. TIMER PROGRAMMING .................................................................................................................... 35 
2. HOT WATER TIMER PROGRAMMING .................................................................................................... 37 
2.1. CHARACTERISTICS: TIMED ............................................................................................................. 37 
2.2. PROCEDURE...................................................................................................................................... 38 
2.3. SERVICE INDICATIONS DISPLAY.................................................................................................... 38 

USE AND INSTALLATION MANUAL

4.2.4. MANUAL REGENERATION................................................................................................................ 39

5. TROUBLESHOOTING...................................................................................................................................... 40

5.1. COLD WATER PART ................................................................................................................................ 40

5.1.1. TROUBLESHOOTING THE VALVE ................................................................................................... 40

5.1.2. TIMER TROUBLESHOOTING............................................................................................................ 40

5.2. HOT WATER PART................................................................................................................................... 41

5.3. SALT STORAGE SKID.............................................................................................................................. 42

6. DISPOSAL OF CONSUMABLES AND MACHINE.......................................................................................... 43

USE AND INSTALLATION MANUAL

1. GENERAL INFORMATION

1.1. PURPOSE AND CONTENTS

The purpose of this manual is to provide the user, who already has basic technical knowledge, with all the specific

information required to operate the machine autonomously under normal circumstances.

It refers to information about the operation and routine maintenance included in the technical manual.

CAUTION

Any operation involving the replacement of parts must be only be carried out by qualified

technical personnel who must possess the following pre-requisites:

General and technical knowledge at a high enough level to understand the content of the manual.

Knowledge of the main hygiene, accident prevention and technological regulations.

Overall knowledge of the machine, as well as knowledge about electrical and hydraulic problems

that could be encountered on-site where the machine is installed.

1.2. SAFETY INFORMATION AND PRECAUTIONS

In order to understand the manual correctly, you must have a sound knowledge of the terms and conventions

used in the documentation. The following symbols are used to draw attention to the various types of hazards and

allow them to be recognised:

WARNING

Danger to the health and safety of the personnel in charge.

WARNING

Danger of electrocution - dangerous voltage.

CAUTION

Danger of damage to the machine or products being processed.

IMPORTANT

Important instructions or information about the product.

Read the instructions before using the equipment.

It indicates a manual adjustment operation that may also include the use of portable equipment or

tools.

It is required to detect a measurement value, to check a warning, to perform a visual check, etc.

Prohibition

USE AND INSTALLATION MANUAL

Only specialised personnel are authorised to operate the machine.

Dispose of the packaging of the parts and any bags or boxes responsibly.

Any parts that are replaced must be disposed of in accordance with current regulations.

DANGER! The tasks described in this manual are reserved for specialised personnel, authorised

by the manufacturer, to perform them in compliance with the regulations in force in the country of

use and the relevant system and work safety standards.

DANGER! Before carrying out any work on the equipment, carefully read all the indications given

in this booklet and in the use and installation manual supplied with the equipment.

DANGER! This manual must be kept in a safe place for future use.

DANGER! Always work when you are in perfect physical condition and wearing personal

protective equipment (safety shoes, gloves, goggles, etc.).

DANGER! When working on the equipment, make sure that there are no unauthorised persons,

inflammable or explosive material and objects that could hinder operations, in the work area.

DANGER! Before carrying out any work on the equipment, ALWAYS disconnect the water and

electricity supply (danger of fatal electrocution!).

DANGER! If any parts have been replaced, do not leave their packaging unattended (e.g. plastic

bags): danger of suffocation for children and animals. Dispose of the packaging according to local

regulations.

DANGER! Any work, tampering or modifications not expressly authorised, which do not respect

the provisions indicated in this manual, could cause harm, injury or fatal accidents and will void

the warranty.

DANGER! Make sure the premises are well ventilated during all work on the equipment.

DANGER! After the work has been completed and before starting up the machine:

make sure that all parts and any safety devices that have been dismantled are correctly

reassembled;

make sure that the machinery has been correctly connected to the electricity supply;

tell the operator about any new devices on the machine.

DANGER! Surfaces get hot during use and may remain hot for some time after the machine has

been switched off, therefore, any maintenance work should be carried out after the machine has

cooled down completely.

DANGER! Some of the metal sheets have sharp inner edges: always wear gloves.

USE AND INSTALLATION MANUAL

1.2.1. PERSONAL PROTECTIVE EQUIPMENT

Table summarising the personal protective equipment (PPE) to be used during the various stages of the machine’s

life cycle.

1. Use heatproof gloves that are suitable for contact with water and the substances used (refer to the safety data sheet of the substances

used to check for any other PPE). Remember that failure to use the personal protective equipment by the operators, specialised personnel or

any other persons assigned to use the equipment could lead to exposure to chemical hazards and cause health problems (depending on the

model).

1.2.2. GENERAL INFORMATION

•The equipment is fitted with electrical and/or mechanically-operated safety devices to protect the operators

and the machine. Consequently, the maintenance technician must not remove or tamper with the above-

mentioned devices without taking adequate precautions. The manufacturer declines all responsibility for any

damage caused by tampering or by failure to use the safety devices.

•Do not make any changes to the spare parts supplied.

•The manual contains a number of diagrams illustrating the machine, or parts thereof, without the protective

devices or with the protective devices removed. This is for explanatory purposes only. Do not use the machine

without the protective devices or with the protective devices disabled.

•Switch the machine off and disconnect it from the water supply in the event of a breakdown or faulty operation.

•Do not use products (even if diluted) which contain chlorine (sodium hypochlorite, hydrochloric or muriatic

acid, etc.) to clean the equipment or the floor underneath it.

•Do not use metal tools to clean the steel parts (metal brushes or scouring pads such as Scotch Brite).

•Do not allow oil or grease to come into contact with plastic parts. Do not allow dirt, grease, food or other

residue to get deposited on the machine.

•Do not spray water or use steam to clean the machine.

Part

replaced

Protective clothing

Safety footwear

Gloves1

Glasses

Helmet

Pump motor

●

○

Pump

●

○

Solenoid valve

●

○

Osmosis module

○

●

Min pressure switch

●

—

Max pressure switch

●

Circuit board

●

—

Adjustments

○

●

○

—

Dismantling

○

●

○

●

Demolition

○

●

○

●

Sanitisation

●

—

Key:

●

PPE REQUIRED

○

PPE AVAILABLE OR FOR USE IF REQUIRED

—

PPE NOT ENVISAGED

USE AND INSTALLATION MANUAL

1.2.3. RESIDUAL RISKS

Using the machine involves some risks which cannot be completely eliminated through design or with the

installation of adequate protective devices. However, the manufacturer has undertaken to inform the operators of

these risks in this manual by specifically indicating the personal protective equipment to use. When repairing the

machine, adequate space has been provided to limit these risks.

To maintain these conditions, the areas around the machine must always be:

- obstacle-free (e.g. ladders, tools, containers, boxes, etc.);

- clean and dry;

- well-lit.

For the sake of providing the customer with comprehensive information, the residual risks remaining on the

machine are indicated below: these actions are deemed inappropriate and are, therefore, strictly forbidden.

Residual risk

Description of hazardous situation

Slipping or falling.

The operator may fall due to water or dirt on the floor.

Burns/grazes (e.g. from hot components).

The operator deliberately or involuntarily touches parts

inside the machine without wearing protective gloves.

Electrocution.

Touching live parts while servicing the machine when the

electrical control panel is powered.

Overturning of heavy loads.

When handling the machine or the packaging that

contains it, inadequate lifting systems or accessories are

used or the load is unstable or unbalanced.

Mechanical features of safety devices, risks

•The machine does not have any sharp or protruding parts. The protective devices for the mobile and live

parts are screwed onto the structure and cover to prevent accidental access.

Protective devices installed on the machine

•The protective devices on the machine are:

fixed protective guards (e.g. casings, covers, side panels, etc.), fixed to the machine and/or frame with

screws or quick-release connectors which can only be removed or opened with specific tools.

Inhaltsverzeichnis

Andere Electrolux Steuereinheit Handbücher

Electrolux

Electrolux ControlBox24/7 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung