Electrolux EGG7222SX Bedienungsanleitung

SERVICE MANUAL

C O N T E N T S

1. GENERAL NOTES 2

2. HOW DOES GAS BURNER OPERATE 3

3. COMPONENTS SPECIFICATION 4

3.1 City gas a essories 5

4. TOOLS 6

5. REPAIR PROCESS 6

5.1 Remove the dirty oil from nozzle

5.2 Remove the gas valve

6. WIRING DIAGRAM 8

7. CONVERSION DETAILS 9

8. TAKE CARE OF GLASS TOP 9

9. SPARE PARTS 10

10. TROUBLE SHOOTING 19

1. GENERAL NOTES

1.1 WARNING: For models which connect to mains electrical power, before exposing an of the internal

electrical wiring the appliance must be disconnected from electrical power b unplugging the service cord

from the electrical outlet. For models which connect to batter power, before exposing an of the internal

electrical wiring the appliance must be remove the batter also.

1.2 An servicing carried out on gas containing components where seals are broken including manifold,

regulator, valves and burner suppl pipes should be followed b a leak test. Gross leaks can be detected b

connecting a manometer to the regulator test point, pressurising the manifold and then shutting off the gas

with a ball valve. A falling manometer reading indicates a leak. Small leaks can be located with soap and

water applied at the connection.

1.3 Burner suppl pipes leading from the burner control to the burner should have their compression fittings

tightened firml but not over tightened (If a torque spanner is used set this to 10  12Nm). If the tubes are

damaged the should be replaced. The soundness of the connections on the burner suppl tubes can be tested

b blocking the injector orifice temporaril , eg. b fitting an injector that has been blocked and leak testing

the fittings.

1.4 When reassembling the appliance any earth leads whi h have been dis onne ted must be re- onne ted.

1.5 Reassembl procedures are a reversal of removal procedures.

1.6 Replace the spare part with original spare parts. The modif part must not be used.

1.7 All the screws in this appliance have been designed for difference purpose. The must be use in the right

position and must be the right dimension. If there are an differences from the original design the ma have

the serious accident.

2. HOW DOES GAS BURNER OPERATE

1. Gas tank

2. Low pressure regulator (Safety warning: Do not use high pressure regulator)

3. Flexible rubber hose or copper tube

4. Elbow coupling gas with fibre washer (Warning: Do not use regular rubber washer)

5. 2 steps safet valve

6. Burner

7. Ignition switch

8. Batter 1.5V size D

9. Spark generator

10. Spark plug

Gas from the tank (1) is released from the low pressure regulator (2) into the hose or tube (3), travelling pass

the elbow coupling to the valve (4). To ignite the burner, press down and turn the safet valve (5) counter-

clockwise simultaneousl . This opens up the valve, letting the gas to the nozzle of the burner (6), and turns the

ignition switch to on (7) at the same time. The electrical current is automaticall supplied from the batter to

spark plug generator (8), and then to the pin heads (9), causing the ignition (10). The burner is ignited and bursts

into flame (11).

3. COMPONENTS SPECIFICATION

- Glass 2B : Float glass 8.0x500x760 mm

- Bottom plate forming : EG

- Knob : Phenolic PH31 heat + flame resistance

- Washer : fiber

- Hose end : Brass (size1/2)

- Rubber grommet (glass model) : Silicone heat resistance

- Spark generator 4p : 1.5Vdc+90C+electrode10KV

3.1 Citi Gas A essories

- Shutter Aeration (Semi Papid)

(TH-0003/ZA)

- Shutter Altration ( Triple Crown)

(TH-0003/ZB)

- Injector 2.1 (Semi Rapid)

(TH-0003/CD)

- Injector 4.0 (Triple Crown)

(TH-0003/ZA)

- Injector 3.5 (Defendi Outer)

(TH-0003/CL)

- Shutter Aeration (Defendi Outer)

(TH-0003/ZC)

- Injector 1.2 (Defendi Outer)

(TH-0003/CM)

- Shutter Aeration(Defendi Inner)

(TH-0003/ZD)

- Screw, M4x0.7x10 IP

- Screw, M4x0.7x18 H

- Screw, M3x12T + B stainless

- Screw, #6/32 x 9 PPZF

- Screw, #8 x ½ T+ Z

4. TOOLS

- Socket Spanner 7

- Nut spinner No. 7

- Philip / Flat screw driver

- Spanner No. 15

- Nozzle cleaner

- Gas leak detector

5. REPAIR PROCESS

5.1 Remove out the dirt oil from nozzle

1. Clean the head of nozzle with the cloth

2. Use the nozzle cleaner or the needle insert into the hole of nozzle.

3. Do repeat the step 1 and 2 for a few time until the nozzle is clean.

5.2 Removal of Hob & Access to Internal Components

1. Isolate the appliance from batter power.

2. Remove trivets and burners from hob.

3. Remove the control knobs from the valve shafts.

4. Remove burner mount retaining screws, 2 screws per burner and 4 on the wok burner (2.5mm Torque

Screwdriver required).

5. For models with a separate button ignition s stem, remove the switch button and ignition pack retaining nut.

Alternativel , lift the hob sufficientl to access and release the ignition leads and batter suppl cable from

the ignition pack.

6. The hob ma now be lifted awa from the appliance.

B removing the hob the following parts are accessible for service or replacement.

• Burner mounting cups.

• Burner suppl tubes. Note: When fitting the burner tubes to the valves and burner mounting

cups the nuts should be fastened with a torque of 10-12Nm.

• Manifold & Valves. Note: To remove the manifold or valves it will be necessar to isolate and

disconnect the appliance from gas suppl .

• Switch harness assembl and low voltage wiring.

• Ignition spark plug and lead assemblies. These are fastened to the burner bases b retaining clips, located on

the underside of the burner base.

• Ignition pack. For models without a separate ignition switch this is clipped to the base or attached with

double sided adhesive. For models with a separate ignition switch this is fastened to the hob with a retaining

nut. Observe the active & neutral are correctl connected in accordance with the markings on the ignition

pack when replacing this unit.

6. WIRING DIAGRAM

7. CONVERSION DETAILS

The applian e is onvertible between Natural Gas & LP.

Pro edure

1. Turn off gas suppl to appliance.

2. Disconnect appliance from electrical power.

3. Remove the trivets and the burner caps & distributors.

4. Remove the existing injectors and replace with the injectors shown in the table below.

5. Remove the control knobs to access the b -pass screw in the valve bodies.

6. Remove the regulator and replace with appropriate regulator or test point adapter as stated in table below,

and reconnect the appliance.

7. Turn on gas & check for leaks. Replace the Burner crowns & caps.

8. Check and adjust the test point pressure according to the procedure in the installation instructions.

9. Manuall light all burners with a hand held ignition source and operate burners at maximum. Note: Do not

reconnect the appliance to electrical power until this procedure is complete.

10. For each hotplate burner adjust the burner to minimum and screw in the b pass screw until a small stable

flame results. Adjust the burner to maximum and back to minimum to ensure correct adjustment.

11. Re-connect to electrical power and check ignition.

8. TAKE CARE OF GLASS TOP

Persistent stains ma require vigorous rubbing with n lon scourer or creamed powers cleansers. Household

enamel cleaners are available. Following the instruction in their use. Harsh abrasive cleaner ,powder cleaner

steel wool or wax polishes should not be used. Advise end user do not use glass as per working top.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Electrolux Kochfeld Handbücher

Electrolux

Electrolux ICON Designer E30EC70FSS Bedienungsanleitung

Electrolux

Electrolux EW36EC55GB - 36" Smoothtop Electric Cooktop Handbuch

Electrolux

Electrolux EW36IC60I - 36 in. Induction Cooktop Bedienungsanleitung

Electrolux

Electrolux EGT7828CK Bedienungsanleitung

Electrolux

Electrolux E36EC75HSS3 Bedienungsanleitung

Electrolux

Electrolux GK69TSIO Bedienungsanleitung

Electrolux

Electrolux EW36GC55PB0 Bedienungsanleitung

Electrolux

Electrolux 318 200 635 (0606) Rev. A Bedienungsanleitung

Electrolux

Electrolux EW30EC55G - 30" Electric Cooktop Bedienungsanleitung

Electrolux

Electrolux E36GC75E - Icon Cooktops Bedienungsanleitung

Electrolux

Electrolux E36GC65ESS - 30"""" Drop-in Gas Cooktop Bedienungsanleitung

Electrolux

Electrolux 30" Coil Elements Bedienungsanleitung

Electrolux

Electrolux EHG735SP Bedienungsanleitung

Electrolux

Electrolux E30EC65ESS1 Bedienungsanleitung

Electrolux

Electrolux E30GC74GPS - 30" Pro-Style Gas Rangetop Bedienungsanleitung

Electrolux

Electrolux EW36GC55GW - 36in Gas Cooktop Gebrauchsanweisung

Electrolux

Electrolux 318201432 Bedienungsanleitung

Electrolux

Electrolux ICON E36IC75FSS Bedienungsanleitung

Electrolux

Electrolux EHG6341FOK Bedienungsanleitung

Electrolux

Electrolux EW30EC55G - 30" Electric Cooktop Bedienungsanleitung

Electrolux

Electrolux EW30EC55GB1 Bedienungsanleitung

Electrolux

Electrolux E36IC80QSS0 Bedienungsanleitung

Electrolux

Electrolux EW30GC60PS Bedienungsanleitung

Electrolux

Electrolux EW30DS65GB5 Bedienungsanleitung

Beliebte Kochfeld Handbücher anderer Marken

Bonnet

Bonnet OPTIMUM 700 Betriebsanleitung

Jenn-Air

Jenn-Air JGCP430 Bedienungsanleitung

Frigidaire

Frigidaire FES367FCC Kurzanleitung

Ztove

Ztove EZ2 DUO Bedienungsanleitung

Kleenmaid

Kleenmaid cooking GCTK9011 Installationsanleitung

Casselin

Casselin CSASRE24 Bedienungsanleitung

Jenn-Air

Jenn-Air JGC2536EB00 Bedienungsanleitung

Waldorf

Waldorf RN8603E-B Bedienungsanleitung

Whirlpool

Whirlpool SMP658CNEIXL Bedienungsanleitung

Wolf

Wolf CI243C/B Bedienungsanleitung

Fulgor Milano

Fulgor Milano F5PGK305S1 Bedienungsanleitung

GE JP389 Bedienungsanleitung

Wells

Wells WV-2HFG Bedienungsanleitung

IKEA

IKEA Lagan HGA4K Bedienungsanleitung

Samsung

Samsung NA36N9755 Bedienungsanleitung

Miele

Miele KM 404 Bedienungsanleitung

Lacor

Lacor 69562 Technisches Datenblatt

Keating Of Chicago

Keating Of Chicago MG-2 Bedienungsanleitung