Electrolux EIGD55H - Gas Dryer With 8.0 cu. Ft.... Bedienungsanleitung

|nsta||ation |nstructions

Electro[u× Front-Load Gas _ Electric DD'er

|nstrucciones de |nsta|acion

Secadora e[_ctfica y a gas de carga fro_3tal Electro[u×

Instructions d'installation

%cheuse _ gaz et _ l'_[ectficit_ _ chargeme_3t fro_3tal Electro[u×

Finding Information

Please read and save this guide

Thank you for choosing Electrolux, the new premium brand in home appliances. These Installation

Instructions are part of our commitment to customer satisfaction and product quality throughout the life

of your new appliance.

We view your purchase as the beginning of a relationship. To ensure our ability to continue serving you,

please use this page to record important product information.

Keep a record for quick reference

Purchase date

Electrolux model number

Electrolux serial number

For toll-free telephone support in the U.S. and Canada: 1-877-4ELECTROLUX {1-877-435-3287)

For online support and product information visit http://www.electroluxappliances.com

Table of contents

Finding information ......................................................... 2

SAFETY .......................................................................... 3

• Pre-installation requirements ...................................... 3

Installation requirements ............................................. 4-9

Electrical system requirements ................................... 4

Gas supply requirements ............................................ 5

Exhaust system requirements ................................. 5-7

Mobile home installation ............................................. 7

Clearance requirements .............................................. 8

installed dimensions ................................................... 9

Installation instructions ........................................... 10-18

Electrical installation ................................................. 10

Grounding requirements - Electric dryer (USA) ........ 10

Grounding requirements - Electric dryer (Canada)... 11

Grounding requirements - Gas dryer ........................ 11

Electrical connection - Electric dryer (3-wire cord)... 12

Electrical connection - Electric dryer (4-wire cord)... 13

Gas connection ........................................................ 14

Water connection (Steam Model only) ................. 15-16

General installation ................................................... 17

Performing installation cycle .................................... 18

Reversing door ........................................................ 19-24

Options ......................................................................... 25

Accessories .............................................................. 25

Replacement parts ................................................... 25

Notes ............................................................................ 26

Safety

Important Safety Instructions

Recognize safety symbols, words and

labels

Safety items throughout this manual are labeled

with a WARNING or CAUTION based on the risk

type as described below:

/_X WARNmNG This symbol alerts you to situa-

tions that may cause serious body

harm, death or property damage.

/_ CAUTmON This symbol alerts you to situa-

tions that may cause bodily injury

or property damage.

or in Canada, CAN/ACG B149.1-2000.

The dryer is designed under ANSI Z 21.5.1 or

ANSI/UL 2158- CAN/CSA C22.2 No. 112 (latest

editions) for HOME USE only. This dryer is not

recommended for commercial applications such

as restaurants, beauty salons, etc.

The instructions in this manual and all other

literature included with this dryer are not meant

to cover every possible condition and situation

that may occur. Good safe practice and caution

MUST be applied when installing, operating and

maintaining any appliance.

Read all of the following instructions before

installing and using this appliance:

• Destroy the carton and plastic bags after the dryer

is unpacked. Children might use them for play.

Cartons covered with rugs, bedspreads, or plastic

sheets can become airtight chambers causing suf-

focation. Place all materials in a garbage container

or make materials inaccessible to children.

• Clothes dryer installation and service must be

performed by a qualified installer, service agency

or the gas supplier.

• Install the clothes dryer according to the manu-

facturer's instructions and local codes.

• The electrical service to the dryer must conform

with local codes and ordinances and the latest

edition of the National Electrical Code, ANSI/

NFPA 70, or in Canada, the Canadian electrical

code C22.1 part 1.

• The gas service to the dryer must conform with

local codes and ordinances and the latest edi-

tion of the National Fuel Gas Code ANSI Z223.1,

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Clear the room, building or area of all occupants.

• Immediately call your gas supplier from a neigh-

bor's phone. Follow the gas supplier's instruc-

tions.

If you cannot reach your gas supplier, call the fire

department.

Save these instructions for future

reference.

PreoinstaHation requirements

Tools and materials needed for installation:

Adjustable Phillips, straight, & Adjustable

pliers square bit screwdrivers wrench Universal wrench Pipe wrench LP-resistant Carpenter's level

supplied with for gas thread tape

matching washer supply (for natural gas

or LP supply)1//, NPT union flare

3-wire or 4-wire 4 in. gas line adapters (x2) and

240 volt cord kit (10.2 cm) shutoff valve flexible gas supply line

(electric dryer) clamp (gas dryer) (gas dryer)

External

vent hood

4 inch, rigid metal or Metal foil tape

semi-rigid metal exhaust duct work (not duct tape)

installation Requirements

Electrical system requirements

Electrical requirements for electric d_jer:

CIRCUIT - individual 30 amp. branch circuit

fused with 30 amp. time delay fuses or circuit

breakers. Use separately fused circuits for

washer and dryer. DO NOT operate a washer

and a dryer on the same circuit.

POWER SUPPLY - 3-wire or 4-wire, 240 volt,

single phase, 60 Hz, Alternating Current.

3-WIRE POWER SUPPLY CORD KIT (not supplied)

3-wire receptacle

(NEMA type 10-30R)

The dryer MUST employ a 3-conductor power

supply cord NEMA 10-30 type SRDT rated at

240 volt AC minimum, 30 amp, with 3 open

end spade lug connectors with upturned ends

or closed loop connectors and marked for use

with clothes dryers. For 3-wire cord connection

instructions see ELECTRICAL CONNECTIONS

FOR A 3-WIRE SYSTEM.

4-WIRE POWER SUPPLY CORD KIT (not supplied)

4-wire receptacle

(NEMA type 14-30R)

The dryer MUST employ a 4-conductor power

supply cord NEMA 14-30 type SRDT or ST (as

required) rated at 240 volt AC minimum, 30 amp,

with 4 open end spade lug connectors with

upturned ends or closed loop connectors and

marked for use with clothes dryers. For 4-wire

cord connection instructions see ELECTRICAL

CONNECTIONS FOR A 4-WIRE SYSTEM.

OUTLET RECEPTACLE - NEMA 10-30R or NEMA

14-30R receptacle to be located so the power

supply cord is accessible when the dryer is in the

installed position.

GROUNDING CONNECTION - See "Grounding

requirements" in Electrical installation section.

Electrical requirements for gas d_jer:

CIRCUIT - individual, properly polarized and

grounded 15 amp. branch circuit fused with 15

amp. time delay fuse or circuit breaker.

POWER SUPPLY - 2-wire, with ground, 120 volt,

single phase, 60 Hz, Alternating Current.

POWER SUPPLY CORD - The dryer is equipped

with a 120 volt 3-wire power cord.

GROUNDING CONNECTION - See "Grounding

requirements" in Electrical installation section.

Grounding type

wall receptacle Do not, under -'_

any circumstances,

cut, remove,

or bypass the

grounding prong.,

Powercord with

3-prong grounded plug

Installation Requirements

Gas supply requirements

1. Installation MUST conform with local codes, or

in the absence of local codes, with the National

Fuel Gas Code, ANSI Z223.1 (latest edition).

2. The gas supply line should be 1/2 inch (1.27

cm) pipe.

3. If codes allow, flexible metal tubing may be

used to connect your dryer to the gas supply

line. The tubing MUST be constructed of

stainless steel or plastic-coated brass.

Exhaust system requirements

The gas supply line MUST have an individual

shutoff valve.

A 1/8 inch (0.32 cm) N.RT. plugged tapping,

accessible for test gauge connection, MUST

be installed immediately upstream of the gas

supply connection to the dryer.

6. The dryer MUST be disconnected from the

gas supply piping system during any pressure

testing of the gas supply piping system at test

pressures in excess of 1/2 psig (3.45 kPa).

7. The dryer MUST be isolated from the gas supply

piping system during any pressure testing of the

gas supply piping system at test pressures equal

to or less than 1/2 psig (3.45 kPa).

8. Connections for the gas supply must comply

with the Standard for Connectors for Gas

Appliances, ANSI Z21.24.

Use only 4 inch (10.2 cm) diameter (minimum) rigid

or flexible metal duct and approved vent hood

which has a swing-out damper(s) that open when

the dryer is in operation. When the dryer stops,

the dampers automatically close to prevent drafts

and the entrance of insects and rodents. To avoid

restricting the outlet, maintain a minimum of 12

inches (30.5 cm) clearance between the vent hood

and the ground or any other obstruction.

The following are specific requirements

for proper and safe operation of your

dryer.

Correct Incorrect

If your present system _smade up of plastic

duct or metal foil duct, replace it with a rigid or

semi-rigid metal duct. In Canada and the United

States if metal (foil type) duct is installed, it must

be of a specific type identified by the appliance

manufacturer as suitable for use with clothes

dryers and in the United States must also comply

with the Outline for Clothes Dryer Transition Duct,

UL standard 2158A. Also, ensure the present duct

is free of any lint prior to installing dryer duct.

installation Requirements

Exhaust system requirements, continued

The dryer must be connected to an exhaust

outdoors. Regularly inspect the outdoor exhaust

opening and remove any accumulation of lint

around the outdoor exhaust opening and in the

surrounding area.

MAXIMUM LENGTH

of 4" (10.2cm) Rigid Metal Duct

VENT HOOD TYPE

(Preferred)

(10.2cm) Iouvered

125 ft. (38.10m)

115 ft. (35.05m)

105 ft. (32.00m)

95 ft. (28.96m)

85 ft. (25.91 m)

2.5"

(6.35cm)

110 ft. (33.53m)

100 ft. (30.48m)

90 ft. (27.43m)

80 ft. (24.38m)

70 ft. (21.34m)

MAXIMUM LENGTH

of 4" (10.2cm)Semi-Rigid Metal Duct

VENT HOOD TYPE

(Preferred)

(10.2cm) Iouvered

60 ft. (18.29m)

50 ft. (15.24m)

40 ft. (12.19m)

NOT RECOMMENDED

2.5"

(6.35cm)

45 ft. (13.72m)

35 ft. (10.67m)

25 ft. (7.62m)

Install male fittings in correct direction:

In installations where the exhaust system is not

described in the charts, the following method

must be used to determine if the exhaust system

is acceptable:

CORRECT INCORRECT

Installation Requirements

Exhaust system requirements, continued

Connect an inclined or digital manometer

between the dryer and the point the exhaust

connects to the dryer.

Set the dryer timer and temperature to air fluff

(cool down) and start the dryer.

Read the measurement on the manometer.

The system back pressure MUST NOT be

higher than 1.0 inch of water column. If the

system back pressure is less than 1.0 inch of

water column, the system is acceptable. If the

manometer reading is higher than 1.0 inch of

water column, the system is too restrictive and

the installation is unacceptable.

Although vertical orientation of the exhaust system

is acceptable, certain extenuating circumstances

could affect the performance of the dryer:

• Only the rigid metal duct work should be used.

Venting vertically through a roof may expose

the exhaust system to down drafts causing an

increase in vent restriction.

Running the exhaust system through an

uninsulated area may cause condensation and

faster accumulation of lint.

Compression or crimping of the exhaust system

will cause an increase in vent restriction.

The exhaust system should be inspected and

cleaned a minimum of every 18 months with

normal usage. The more the dryer is used,

the more often you should check the exhaust

system and vent hood for proper operation.

Exhaust direction

Directional exhausting can be accomplished by

installing a quick-turn 90° dryer vent elbow directly

to exhaust outlet of dryer. Dryer vent elbows are

available through your local parts distributor or

hardware store.

See also CLEARANCE REQUIREMENTS on the

next page.

Manufactured or mobile home installation

1. Installation MUST conform to current

Manufactured Home Construction & Safety

Standard, Title 24 CFR, Part 32-80 (formerly the

Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280) or Standard

CAN/CSAZ240 MH.

2. Dryer MUST be exhausted outside (outdoors, not

beneath the mobile home) using metal ducting

that will not support combustion. Metal ducting

must be 4 inches (10.16 cm) in diameter with no

obstructions. Rigid metal duct is preferred.

3. If dryer is exhausted through the floor and

area beneath the mobile home is enclosed,

the exhaust system MUST terminate outside

the enclosure with the termination securely

fastened to the mobile home structure.

4. Refer to previous sections in this guide for other

important exhaust venting system requirements.

5. When installing a gas dryer into a mobile home,

a provision must be made for outside make up

air. This provision is to be not less than twice

the area of the dryer exhaust outlet.

6. Installer MUST anchor this (1) dryer or (2) dryer

mounted on pedestal to the floor with approved

Mobile Home Installation Kit - P/N 137067200.

installation Requirements

Cmearance requirements

iNSTALLATiON iN A RECESS OR CLOSET

1. A dryer installed in a bedroom, bathroom,

recess or closet, MUST be exhausted outdoors.

2. No other fuel burning appliance shall be

installed in the same closet as the gas dryer.

3. Your dryer needs the space around it for proper

ventilation.

DO NOT install your dryer in a closet with a solid

door.

.Closet door ventilation required: A minimum

of 120 square inches (774.2 cm 2)of opening,

equally divided at the top and bottom of the

door, is required. Openings should be located

3 inches (7.6 cm) from bottom and top of door.

Openings are required to be unobstructed

when a door is installed. A Iouvered door with

equivalent air openings for the full length of the

door is acceptable.

60 sq. in.

(387.1cm 2}

60 sq. in.

(387.1cm 2)

MINIMUM INSTALLATION CLEARANCES -Inches (cm)

SIDES REAR TOP FRONT

Alcove 0" (0 cm) 0" (0 cm)* 0" (0 cm) n/a

Under- 0" (0 cm) 0" (0 cm)* 0" (0 cm) n/a

Counter

Closet 0" (0 cm) 0" (0 cm)* 0" (0 cm) 1" (2.54 cm)

For other than straight back venting, a quick-turn 90°

dryer vent elbow must be installed to achieve 0" (0 cm)

o" t

(Ocm)

Installation Requirements

Installed dryer dimensions

50.6" (128.5cm)*

to clear open door

freestand dryer

on floor

optional pedestal

floor line

31.59" (8Ocm)*

to front of closed door

53.00"

(134.5cm)

38.00"

(96.5cm)

* To obtain these minimal depth dimensions, dryer must either be vented straight back or

with a quick-turn 90 ° elbow. Connection of water inlet hose on Steam Models adds 3/4 in.

(2 cm) to installation depth. Upward venting of exhaust on pedestal-mounted or freestandin 9

dryer adds approximately 4 in. (10.2 cm) to installation depth. Downward venting of exhaust

on pedestal-mounted dryer adds approximately 1.7 in. (4.3 cm) to installation depth.

27.00 --

(68.5cm)

gas supply

pipe on rear

15.25"

(4t.5cm)

(9.5cm)

(34.5cm)

to center of rear vent

50.6" (128.5cm)

to clear open door 31.50" (80cm)*

to front of closed door

75.75"

(192.5cm)

27.00" b-

(68.5cm)

gas supply

pipe on rear

39.00"

(99cm)

*To obtain these minimal depth dimensions, dryer must either be vented straight back or with a quick-turn 90 ° elbow.

Connection of water inlet hose on Steam Models adds 3/4 in. (2 cm) to installation depth. Upward or downward venting

of exhaust on stacked dryer adds approximately 4 in. (10.2 cm) to installation depth.

electrical

supply on

rear of unit

height for

rear vent

18.25"

(46.5cm)

electrical

supply on

rear of unit

centerline

height for

41.OO"

(104cm)

"l installation instructions

The following are specific requirements for proper

and safe electrical installation of your dryer. Failure

to follow these instructions can create electrical

shock and!or a fire hazard.

ELECTRICAL SHOCK HAZARD

This appliance MUST be properly grounded.

Electrical shock can result if the dryer _snot

properly grounded. Follow the instructions in

this manual for proper grounding.

Do not use an extension cord w_th this dryer.

Some extension cords are not designed to

withstand the amounts of electrical current this

dryer utilizes and can melt, creating electrical

shock and/or fire hazard. Locate the dryer

within reach of the receptacle for the length

power cord to be purchased, allowing some

slack in the cord. Refer to the pre-installation

requirements in this manual for the proper

power cord to be purchased.

ELECTRICAL SHOCK HAZARD

A U.h-approved strain relief must be installed

onto power cord. If the strain relief is not

attached, the cord can be pulled out of the

dryer and can be cut by any movement of the

cord, resulting in electrical shock.

Do not use an aluminum wired receptacle with

a copper wired power cord and plug (or vice

versa). A chemical reaction occurs between

copper and aluminum and can cause electrical

shorts. The proper wiring and receptacle is a

copper wired power cord w_th a copper wired

receptacle.

Dryers operating on 208 volt power supply w_ll

have longer drying times than dryers operating

on 240 volt power supply.

ELECTRICAL SHOCK HAZARD

Improper connection of the equipment grounding

conductor can result in a risk of electrical shock.

Check with a hcensed electrician _fyou are in

doubt as to whether the appliance is properly

grounded.

For a grounded, cord-connected dryer:

1. The dryer MUST be grounded. In the event of

a malfunction or breakdown, grounding will

reduce the risk of electrical shock by a path of

least resistance for electrical current.

2. After you purchase and install a 3 wire or 4

wire power supply cord having an equipment-

grounding conductor and a grounding plug

that matches you wiring system, the plug

MUST be plugged into an appropriate, copper

wired receptacle that is properly installed and

grounded in accordance with all local codes and

ordinances. If in doubt, call a licensed electrician.

DO NOT modify the plug you've installed on this

appliance.

For a permanently connected dryer:

1. The dryer MUST be connected to a grounded

metal, permanent wiring system; or an

equipment grounding conductor must be run

with the circuit conductors and connected to

the equipment-grounding terminal or lead on

the appliance.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Electrolux Trockner Handbücher

Electrolux

Electrolux TK K2 E Bedienungsanleitung

Electrolux

Electrolux QuickDry N1130 Bedienungsanleitung

Electrolux

Electrolux TWSL4E300 Bedienungsanleitung

Electrolux

Electrolux WT40 Bedienungsanleitung

Electrolux

Electrolux EDE 425 M Kurzanleitung

Electrolux

Electrolux Zanussi ZDE 57140W Bedienungsanleitung

Electrolux

Electrolux EDC 5470 Bedienungsanleitung

Electrolux

Electrolux T5290 Bedienungsanleitung

Electrolux

Electrolux T4190 Bedienungsanleitung

Electrolux

Electrolux EDH803BEWA Bedienungsanleitung

Electrolux

Electrolux EIMED55I RR Bedienungsanleitung

Electrolux

Electrolux IQ-Touch EIMGD55IIW Montageanleitung

Electrolux

Electrolux EDH903R9WB Bedienungsanleitung

Electrolux

Electrolux ZDC 67550W Bedienungsanleitung

Electrolux

Electrolux EDE 5130 Bedienungsanleitung

Electrolux

Electrolux TDV 850 Bedienungsanleitung

Electrolux

Electrolux Wave-Touch 137018100 A Bedienungsanleitung

Electrolux

Electrolux T4650 Bedienungsanleitung

Electrolux

Electrolux EDH903BEWN Bedienungsanleitung

Electrolux

Electrolux EWMGD70J IW Bedienungsanleitung

Electrolux

Electrolux EW7H558E2 Bedienungsanleitung

Electrolux

Electrolux EIMED55IIW - 27" Electric Dryer Bedienungsanleitung

Electrolux

Electrolux EDH804H3WB Bedienungsanleitung

Electrolux

Electrolux EIED55IKG - 8.0 cu. Ft. Electric Dryer Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung

Frigidaire

Frigidaire CAQE7077KW0 Betriebsanleitung

Bosch

Bosch WTX8HKM9SN Bedienungsanleitung

Sharp

Sharp KD-NHH9S7GW2-PL Bedienungsanleitung

Samsung

Samsung DV431AEPXAC Bedienungsanleitung

Speed Queen

Speed Queen ADE3TRW5431AW01 Bedienungsanleitung