Electrolux ECCG3672AS Bedienungsanleitung
A Quick Guide to Getting Started
913531544
Rev. A
(March 2021)
Before you begin
1. Remove all packaging material and tape.
2. Make sure your burner caps are centered on the burners
and installed correctly.
3. Place the center cooktop grate first, then position the
left and right grates in place. Refer to your Use & Care
Manual for detailed instructions.
OPERATING THE BURNERS
1. Place your cookware on the burner.
2. Push in and turn the cooktop knob to the
position to ignite the burner.
3. Check the burner to make sure it has a steady
flame.
4. Once the burner is lit, keep the knob pressed in
for a few seconds. If the burner goes out, wait a
few moments and try again.
5. Turn the burner knob to adjust the flame size.
NOTE: A clicking sound will occur on all the burners
when a control knob is pushed in.
Don't cook with the knob in the position.
BURNER KNOB POSITIONS:
position
HIGH and LOW flame settings
Burner outer ring flame setting
Burner inner ring flame setting
Burner electric ignition
Gas Cooktop Basics
SETTING YOUR FLAME SIZE
The color of the flame is the key to proper
burner adjustment. USING THE INNER AND OUTER RINGS
Once the burner is lit, it will be on the highest setting.
To lower the outer ring
setting, turn the knob to
left.
To turn off the outer ring,
continue to turn the knob
left.
To control only the inner
ring, push the cooktop
knob in and turn left.
Continue to turn the knob
left to decrease the inner
ring setting.
Burner Installation
A good flame is
clear, blue and
hardly visible. Adjust
or clean the burner
if flame is yellow-
orange.
Start on the highest setting and lower the setting
as needed for general cooking needs.
Use a medium or low flame when thickening
sauces or to maintain a slow boil.
All burner components must be properly installed before first use
to ensure proper ignition and gas flame size.
Place the brass coated burners in the front left and front right
zones. Place the black coated burners in all the other zones.
1. Align the burner skirt openings with the openings in the burner
base.
2. Center the flame spreader crown on the burner skirt.
3. Center and level the burner cap on top.
Peace of Mind & Protection
Unlock exclusive benefits by registering your product with us.
Review your registration card for all the ways to register or visit us
online directly.
Sustainability,
together
ElectroluxAppliances.com
(877) 435-3287
10200 David Taylor Drive
Charlotte, NC 28262
ElectroluxAppliances.ca
(800) 265-8352
5855 Terry Fox Way
Mississauga, ON L5V 3E4
We're committed to more
sustainable eating from how
we store foods to how we
prepare them.
FAQs
• Why is my gas cooktop not working?
Make sure your cooktop knob is turned to position when turning on the surface burner. Check to make sure
your cooktop burner ports aren't clogged. Your Use & Care Manual has instructions on how to properly clean
your cooktop burners.
• Why is the burner flame uneven?
Clogged burner ports or slots can cause uneven flames. Check to make sure the cooktop burners are
installed and placed correctly. Burner caps should be level and seated correctly on the burner heads.
• Why is my burner flame too high?
The cooking setting may be too high. Use your cooktop knob to reduce to a lower setting.
Burner caps not placed properly can cause the flame to be too high. Check the fit of the burner caps by
sliding it side to slide when the cooktop is cool.
Always refer to your Use &Care Manual for more tips and instructions.
Visit the ElectroluxUS channel on YouTube to access helpful how to
videos.
Protect your cooktop by quickly cleaning up spills when they happen.
Before cleaning the cooktop, be sure the controls are turned to OFF and the cooktop burners are cool.
For general cleaning, wipe dry with a clean, damp cloth to avoid scratches. For instructions on how to clean your
cooktop grates and burners, refer to your Use & Care Manual.
Care and Cleaning
Using the Griddle
Your cooktop has two standard sized burners in the center that can be used to heat larger cookware like a
griddle.
1. Set the griddle on top of the center grate by
positioning the feet on the top and bottom.
2. Preheat the griddle for 5 minutes on medium to
medium-low setting.
Use non-stick cooking spray or oil as needed. Slowly
preheating the griddle ensures even heat distribution
for best cooking results.
We recommend hand washing the griddle with a brush and hot water. Use a little soap if needed, and rinse well.
Dry with a lint-free cloth and store in a dry place. Avoid cleaning the griddle in the dishwasher.
Andere Handbücher für ECCG3672AS
1
Inhaltsverzeichnis
Andere Electrolux Kochfeld Handbücher
Electrolux
Electrolux EHG678B Bedienungsanleitung
Electrolux
Electrolux EKC6700 Bedienungsanleitung
Electrolux
Electrolux EHL7640FOK Bedienungsanleitung
Electrolux
Electrolux EGC3313 Bedienungsanleitung
Electrolux
Electrolux EGH6242 Bedienungsanleitung
Electrolux
Electrolux DMSL8350UO Bedienungsanleitung
Electrolux
Electrolux EGT6342NOX Bedienungsanleitung
Electrolux
Electrolux EHC325BA Bedienungsanleitung
Electrolux
Electrolux EHL6645X Bedienungsanleitung
Electrolux
Electrolux EIL83443 Bedienungsanleitung
Electrolux
Electrolux EHI8742FOZ Bedienungsanleitung
Electrolux
Electrolux GK58TSO Bedienungsanleitung
Electrolux
Electrolux EHF6140ISK Bedienungsanleitung
Electrolux
Electrolux CGS6436BX Bedienungsanleitung
Electrolux
Electrolux EHD68100I Bedienungsanleitung
Electrolux
Electrolux EGG3222N Bedienungsanleitung
Electrolux
Electrolux EGH6343RON Bedienungsanleitung
Electrolux
Electrolux EIP8546 Bedienungsanleitung
Electrolux
Electrolux EHF6343FOK Bedienungsanleitung
Electrolux
Electrolux EGC3313NOK Bedienungsanleitung
