Electrolux EFC 1540 Bedienungsanleitung
Instruction Manual
Manual de instrucciones
Bedienungsanleitung
Manual de Instruções
PT 30
DE 21
ES 12
GB 3
EFC 6540
EFC 7540
EFC 9540
EFC 1540
3GB
CONTENTS
Dear Customer,
If you follow the recommendations
contained in this Instruction Manual, your
appliance will give you constant high per-
formance and will remain efficient for
many years to come.
RECOMMENDATIONS AND SUGGESTIONS 4
CHARACTERISTICS 5
INSTALLATION 6
USE 9
MAINTENANCE 10
4GB
RECOMMENDATIONS AND SUGGESTIONS
INSTALLATION
• The manufacturer will not be held liable for any damages resulting
from incorrect or improper installation.
• The minimum safety distance between the cooker top and the
extractor hood is 650 mm.
• Check that the mains voltage corresponds to that indicated on the
rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply
guarantees adequate earthing.
Connect the extractor to the exhaust flue through a pipe of minimum
diameter 120 mm. The route of the flue must be as short as possible.
• Do not connect the extractor hood to exhaust ducts carrying
combustion fumes (boilers, fireplaces, etc.).
• If the extractor is used in conjunction with non-electrical appliances
(e.g. gas burning appliances), a sufficient degree of aeration must
be guaranteed in the room in order to prevent the backflow of exhaust
gas. The kitchen must have an opening communicating directly with
the open air in order to guarantee the entry of clean air.
USE
• The extractor hood has been designed exclusively for domestic use
to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has ben
designed.
• Never leave high naked flames under the hood when it is in operation.
• Adjust the flame intensity to direct it onto the bottom of the pan only,
making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use:
overheated oil can burst into flames.
• The hood should not be used by children or persons not instructed in
its correct use.
MAINTENANCE
• Switch off or unplug the appliance from the mains supply before
carrying out any maintenance work.
• Clean and/or replace the Filters after the specified time period.
• Clean the hood using a damp cloth and a neutral liquid detergent.
650 mm min.
5GB
CHARACTERISTICS
Dimensions
Components
Ref. Q.ty Product Components
11 HoodBody,completewith:Controls,Light,Blower,
Filters
21 TelescopicChimneycomprising:
2.1 1 UpperSection
2.2 1 LowerSection
91ReducerFlangeø150-120mm
14.1 2 AirOutletConnectionExtension
15 1 AirOutletConnection
Ref. Q.ty Installation Components
7.2.1 2 UpperChimneySectionFixingBrackets
7.3 1 AirOutletConnectionSupport
11 6 WallPlugs
12a 6 Screws4,2x44,4
12c 6 Screws2,9x9,5
Q.ty Documentation
1 InstructionManual
1 Warranty
740
870
1200
260
300
64
42
650 min.
490 60
598-898
108
150
2.1
2.2
2
12c
12a 7.2.1 11
11
12a
1
9
7.3
14.1
15
6GB
11
12a
320 X
116
1÷2
116
650 min.
7.2.1
INSTALLATION
Walldrillingandbracketfixing
Wall marking:
• Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of
the area in which the hood will be installed.
• Draw a horizontal line at 650 mm above the hob.
• Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the
centre (notch) with the vertical reference line.
• Mark the wall at the centres of the holes in the bracket.
• Place bracket 7.2.1 on the wall as shown at X mm below the first bracket (X = height of the upper
chimney section supplied), aligning the centre (notch) with the vertical line.
• Mark the wall at the centres of the holes in the bracket.
• Mark a reference point as indicated at 116 mm from the vertical reference line and 320 mm above
the horizontal reference line.
• Repeat this operation on the other side.
• Drill ø 8 mm holes at all the centre points marked.
• Insert the wall plugs 11 in the holes.
• Fix the lower bracket 7.2.1 using the 12a screws (4,2 x 44,4) supplied.
• Fix the upper bracket 7.2.1 and the air outlet connection support 7.3 together using the 2 screws
12a (4,2 x 44,4) supplied.
• Insert the two screws 12a (4,2 x 44,4) supplied in the hood body fixing holes, leaving a gap of 5-6
mm between the wall and the head of the screw.
7GB
Mounting the hood body
• Before attaching the hood body, tighten the two
screws Vr located on the hood body mounting
points.
• Hook the hood body onto the screws 12a
• Fully tighten support screws 12a
• Adjust screws Vr to level the hood body.
Connections
DUCTED VERSION AIR EXHAUST SYSTEM
When installing the ducted version, connect the hood to the chimney using either a flexible or rigid
pipe ø 150 or 120 mm, the choice of which is left to the installer.
• To install a ø 120 mm air exhaust connection,
insert the reducer flange 9on the hood body
outlet.
• Fix the pipe in position using sufficient pipe
clamps (not supplied).
• Remove any activated charcoal filters.
RECIRCULATION VERSION AIR OUTLET
• Put connection 15 into the connection support 7.3.
• Insert the connection extension pieces laterally 14.1
in connection 15.
• Make sure that the outlet of the extension pieces
14.1 is horizontally and vertically aligned with the
chimney outlets.
• Connect the air outlet connection 15 to the hood
body outlet using either a flexible or rigid pipe ø 150
mm, the choice of which is left to the installer.
• Ensure that the activated charcoal filters have been
inserted.
12a
Vr
9
ø 120ø 150
ø 150
14.1
15
8GB
ELECTRICAL CONNECTION
• Connect the hood to the mains through a two-pole
switch having a contact gap of at least 3 mm.
• Remove the grease filters and verify that the
connector of the feeding cable is correctly inserted
in the socket placed on the side of the fan Enlever
les filtres à graisse et s'assurer que le connecteur
Flueassembly
Upper exhaust flue
• Slightly widen the two sides of the upper flue
and hook them behind the brackets 7.2.1, making
sure that they are well seated.
• Secure the sides to the brackets using the 4
screws 12c (2,9 x 9,5) supplied.
• Make sure that the outlet of the extensions pieces
is aligned with the chimney outlets.
Lower exhaust flue
• Slightly widen the two sides of the flue and hook
them between the upper flue and the wall, making
sure that they are well seated.
• Fix the lower part laterally to the hood body using
the 2 screws 12c (2,9 x 9,5) supplied.
12c
2.1
2.2
2
7.2.1
12c
9GB
USE
ControlPanel
The hood can be switched on pushing directly onto the requested speed without firstly having to select
0/1 button.
KEY LED FUNCTIONS
L0/1 Light Turns lighting on and off.
T1 0/1 Motor on First speed.
When pressed for about 1 seconds the motor is switched off.
T2 Speed on Second speed.
T3 Speed on Third speed.
T4 Speed Fixed Max. speed
Flashing Intensive speed.
Suitable for the strongest cooking vapours and odours.
The function becomes active when the button is pushed
for about 2 seconds. After 10 minutes of functioning it
turns off automatically. This function can be interrupted
by means of pressing any of the buttons.
S1 Led Fixed Indicates that the Metal grease filters saturation alarm
has been triggered, and the filters need to be washed.
The alarm is triggered after 100 working hours. (Reset;
check the Maintenance-paragraph)
Flashing indicates that the activated charcoal odour filter saturation
alarm has been triggered, and the filter has to be replaced;
the metal grease filters must also be washed. The
activated charcoal odour filter is triggered after 200
working hours. (Activation and Reset; check the
Maintenance-paragraph)
L
S1
T1 T2 T3 T4
10GB
MAINTENANCE
Greasefilters
CLEANING METAL SELF- SUPPORTING GREASE FILTERS
Alarm signal reset
• Switch off the lights and extractor motor.
• Press button T3 for at least 3 seconds, until the
leds start to flash.
Cleaning the filters
• The filters must be cleaned every 2 months of
operation, or more frequently for particularly
heavy usage, and can be washed in a dishwasher.
• Remove the filters one at a time by pushing them
towards the back of the group and pulling down
at the same time.
• Wash the filters, taking care not to bend them.
Allow them to dry before refitting.
• When refitting the filters, make sure that the
handle is visible on the outside.
Activatedcharcoalfilter(Recirculationversion)
REPLACING THE ACTIVATED CHARCOAL FILTER
Alarm signal activation
• In Recirculation version Hoods, the Filter saturation alarm can be enabled on installation or at a later
date. Turn the Lights and the suction Motor off.
• Disconnect the Hood using the Main switch or the double-pole switch on the mains power supply.
• Restore the connection by pressing and holding T1.
• Release the button. All five LEDs are turned on
• Within 3 seconds press T1 until LEDs T1 and T4 flash in confirmation:
LED flashes twice -Activated charcoal filter saturation alarm ENABLED
LED flashes once - Activated charcoal filter saturation alarm DISABLED
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Electrolux Dunstabzugshaube Handbücher
Electrolux
Electrolux EFT 7466 Bedienungsanleitung
Electrolux
Electrolux EFFP45680X Bedienungsanleitung
Electrolux
Electrolux U30306 CH1200-600-900 Bedienungsanleitung
Electrolux
Electrolux EFG315S Bedienungsanleitung
Electrolux
Electrolux PLHV42P8CC Bedienungsanleitung
Electrolux
Electrolux LFP326X Bedienungsanleitung
Electrolux
Electrolux EFT 5529 Bedienungsanleitung
Electrolux
Electrolux PLHV42P8CC Bedienungsanleitung
Electrolux
Electrolux EFP 629 Bedienungsanleitung
Electrolux
Electrolux LFT769X Bedienungsanleitung
Electrolux
Electrolux ZHT 510 Handbuch
Electrolux
Electrolux EFB90566BX Bedienungsanleitung
Electrolux
Electrolux EFC 9420 Bedienungsanleitung
Electrolux
Electrolux LFU116X Bedienungsanleitung
Electrolux
Electrolux IUSL1065CN Bedienungsanleitung
Electrolux
Electrolux LFG9525S Bedienungsanleitung
Electrolux
Electrolux EFV418X Bedienungsanleitung
Electrolux
Electrolux BETA EA 340 S1 BA Bedienungsanleitung
Electrolux
Electrolux KFIA19R Bedienungsanleitung
Electrolux
Electrolux WHSL9062CN Bedienungsanleitung
