Electrolux EWF12033 Bedienungsanleitung
ENGLISH
INSTALLATION
4.
5. Remove the polystyrene base.
6.
Put one of the polystyrene packaging
elements on the floor behind the
appliance. Carefully put down the
appliance with the rear side on it.
Make sure not to damage the hoses.
Pull up the appliance in vertical
position.
11.1Unpacking
Use gloves. Cut and remove four cut
out straps as shown.
1.
Remove the carton box. Remove the
polystyrene packaging materials.
Remove the plastic bag which cover
the machine.
2.
Open the door. Remove the
polystyrene piece from the door seal
and all the items from the drum.
3.
7. Remove the power supply cable and
the drain and inlet hoses from the
hose holders (A) on the rear of the
appliance.
1
2
You are advised to keep all transit
devices so that they can be refitted if
the machine ever has to be
transported again.
All transit bolts and packing must be
removed before using the appliance.
CAUTION!
www.electrolux.com
8.
9. Pull out the plastic spacers.
10. Put the plastic caps in the holes.
You can find these caps in the user
manual bag.
Remove the three transit bolts.
A
1
2
3
Loosen or tighten the feet to adjust
the level. A correct adjustment of
the appliance level prevents
vibration, noise and the movement
of the appliance when in operation.
11.2Positioning
Use a spirit level on the top and
side of the washing machine to
check the levels.
If you do not have a spirit level, as a
guide use the edge of a door frame,
cupboard or bench to check that the
washing machine is leveled.
It is important that your washing
machine stands firm and leveled
on the floor to ensure correct
operation. The appliance must not
be installed behind a lockable
door, a sliding door or a door with
a hinge on the opposite side to
avoid restricting the washing
machine door.
ENGLISH
Never place cardboard, wood or
similar materials under the
machine to compensate for any
unevenness in the floor. Install the
machine on a flat hard floor. Make
sure that air circulation around the
machine is not impeded by carpets,
rugs etc.
When the washing machine is
levelled, try to rock it from corner to
corner. If it does rock, adjust the
legs again until it is levelled and
does not rock.
Connect the water inlet hose to a
tap with 3/4” BSP thread.
Use the hose supplied with the
washing machine. DO NOT USE
OLD HOSES.
The other end of the inlet hose
which connects to the machine can
be turned in any direction.
Simply loosen the fitting, rotate the
hose and retighten the fitting,
making sure there are no water
leaks.
11.3 Water Inlet
Check that the machine does not
touch the wall or cupboard units.
The inlet hose must not be
lengthened. If it is too short and
you do not wish to move the tap,
you will have to purchase a new,
longer hose specially designed for
this type of use.
This could be done by tying it to
the tap with a piece of string or
attaching it to the wall.
In a sink drain pipe branch. This
branch must be above the trap
so that the bend is at least 60 cm
above the ground.
Directly into a drain pipe at a
height of not less than 60 cm
and not more than 90 cm.
The end of the drain hose must
always be ventilated, i.e. the
inside diameter of the drain pipe
must be larger than the outside
diameter of the drain hose.
The drain hose must not be
twisted or curled. Run it along
the floor; only the part near the
drainage point must be raised.
The end of the drain hose can be
positioned in three ways:
Hooked over the edge of a sink
using the plastic hose guide
supplied with the machine.
In this case, make sure the end
cannot come unhooked when
the machine will be emptied.
11.4Water Drainage
www.electrolux.com
For the correct functioning of the
machine, the drain hose must
remain hooked on the proper
support piece situated on the top
part of back side of the appliance.
90 cm
60 cm
This machine is designed to
operate on a 220-240 V,
single-phase, 50 Hz supply.
11.5Electrical Connection
“An incorrect power supply may
void your warranty.”
Check that your domestic electrical
installation can take the maximum
load required (2.1 kW), also taking
into account any other appliances
in use.
The manufacturer declines any
responsibility for damage or injury
through failure to comply with the
above safety precaution.
Should the appliance power supply
cable need to be replaced, this
shall be carried out by our Service
Centre.
When the appliance is installed,
the power supply cable must be
easily accessible.
If this appliance is supplied from a
cord extension set or electrical
portable outlet device, the cord
extension set or electrical portable
device must be positioned so that
it is not subject to splashing or
ingress of moisture.
Connect the machine to
an earthed socket outlet.
CAUTION!
Andere Handbücher für EWF12033
1
Inhaltsverzeichnis
Andere Electrolux Waschmaschine Handbücher
Electrolux
Electrolux EWT 8020 W Bedienungsanleitung
Electrolux
Electrolux EWT8541 Bedienungsanleitung
Electrolux
Electrolux OKO_LAVAMAT 80030 Bedienungsanleitung
Electrolux
Electrolux EWT 1466 HDW Bedienungsanleitung
Electrolux
Electrolux EWF1141AESA Bedienungsanleitung
Electrolux
Electrolux EWF695 Bedienungsanleitung
Electrolux
Electrolux EW6FN428BC Bedienungsanleitung
Electrolux
Electrolux EWFLS70JIW1 Bedienungsanleitung
Electrolux
Electrolux EWF 1476 GDW Bedienungsanleitung
Electrolux
Electrolux WH1018 Bedienungsanleitung
Electrolux
Electrolux EWF 1045 Bedienungsanleitung
Electrolux
Electrolux Compass Pro WN6-8 Bedienungsanleitung
Electrolux
Electrolux EWF14012 Bedienungsanleitung
Electrolux
Electrolux EWF 1487 HDW2 Bedienungsanleitung
Electrolux
Electrolux EWB 85215 W Bedienungsanleitung
Electrolux
Electrolux FOM 71 CLS Bedienungsanleitung
Electrolux
Electrolux EWF9042Q7WB Bedienungsanleitung
Electrolux
Electrolux LAVAMAT 51165 Bedienungsanleitung
Electrolux
Electrolux WH 1075 Bedienungsanleitung
Electrolux
Electrolux EW8F169SA Bedienungsanleitung
