Electrorad ThermaStoreHHR Bedienungsanleitung
ACU006113V01
HIGH HEAT RETENTION STORAGE HEATER
INSTALLATION MANUAL AND INSTRUCTIONS FOR USE
Smart charging
WiFi control
TFT display
Manual de instalación e instrucciones de uso
2
A. PRESENTATION
First of all, thank you for purchasing our products. Before proceeding with its installation, please
read all the instructions and recommendations detailed in this instruction manual, as the manufac-
turer will not be responsible for any breakdown or damage caused by non-compliance. Once the
storage heater is installed, keep this manual in a safe place so that it can be consulted at any time.
B. RECYCLING
Warnings for the correct disposal of the product according to the European Directive 2012/19 / EU.
At the end of its useful life, the product must not be disposed of together with municipal waste. It can
be delivered to specic dierentiated collection centers arranged by the municipal adminis-
trations or to distributors that provide this service. Disposing of an electrical appliance se-
parately means avoiding possible negative consequences for the environment and health
derived from improper disposal and allows recycling of the materials that compose it, thus
obtaining signicant savings in energy and resources. To underline the obligation to collaborate with a
separate collection, the product is marked with a warning not to use traditional containers for disposal.
For more information, contact your local authority or the store where you purchased it for disposal.
C. IMPORTANT SAFETY NOTES
The placement of the heating appliance must be chosen correctly and must
be carried out according the rules.
The equipment must be kept away from all ammable objects .
Children must not be left near the heater without being supervised.
Children under 3 years of age should be kept out of the reach of the applian-
ce unless they are continuously supervised.
Children from 3 years old and under 8 years old should only turn the applian-
ce on / o provided that it has been placed and installed in its intended nor-
mal operating position and that they are supervised or have received ins-
tructions regarding the use of the appliance in a safe and secure manner.
Children from 3 years old and under 8 years old should not plug in, regulate
and clean or carry out maintenance operations.
This appliance can be used by children 8 years of age and older and by
persons with reduced physical, sensory or mental capabilities, if they have
been given appropriate supervision or training regarding the safe use of the
appliance and understand the dangers involved.
Children should be supervised to ensure that they do not play with the
appliance.
Manual de instalación e instrucciones de uso
3
Cleaning and maintenance to be carried out by the user should not be ca-
rried out by children without supervision.
Caution: some parts of this product can become very hot and cause
burns. Particular attention should be paid when children and vulnera-
ble people are present.
In no case should the equipment be covered by clothing, a container or any
other object, nor should it be placed under a closet or any other obstacle that
prevents the circulation of hot air.
WARNING:
To avoid overheating, DO NOT COVER the heater.
The heating appliance should not be placed immediately un-
der a socket outlet.
Avoid using extension cords as these can cause overheating and cause
a re hazard. However, in the case of using an extension cord, the cable
must have a section 1.5mm² / 16 AWG minimum size and that support a
power not less than 2600w in the case of powers up to 2600w, and section
2.5mm² / 14 AWG of minimum size and that supports a minimum power of
3400w for powers from 2600w.
This appliance is intended to be permanently connected. The power supply
circuit of the equipment must incorporate an omnipolar cut-o switch with
a contact separation of at least 3 mm.
The connection cables of the heater itself must not come into contact with
the surface of the appliance, and in the event that they can come into con-
tact, they must be protected with an insulating cover that has an adequate
temperature level.
The equipment must not be installed in places where there is a risk of
splashing water, such as bathtubs, sinks, etc. The equipment must be ins-
talled in such a way that the switches, thermostat, power socket, cannot be
directly or indirectly touched by a person in the bathtub or shower (adhere
the prohibited distances according to REBT).
Manual de instalación e instrucciones de uso
4
If the power cable is damaged, it can only be replaced by an authorised
person, in order to avoid risks. If during the installation and assembly of the
appliance, a part of the thermal insulation or resistance shows damage or
deterioration that impairs the safety of the appliance, it must be replaced by
an identical part.
Before carrying out any operation inside the appliance, do not forget
to disconnect the power supply.
Contact with the core temperature probe can cause an electrical hazard. The
probe cannot be manipulated, moved or touched.
Never open the appliance while it is charged.
The presence in the environment of tobacco smoke or suspended parti-
cles, atmospheric pollution, etc., could darken the wall surfaces near the
storage heater
Always observe the safety measures when placing the heater on the wall.
The electrical installation must have a switch with fuses or magnetothermic
protection. Likewise, a dierential protection against ground faults is advi-
sable. The voltage and frequency values of the power supply must be the
same as those indicated on the nameplate.
It is possible that the radiator could create slight noises at the beginning of
its operation, it is something normal due to expansions and contractions.
As the days go by, this noise disappears.
After the appliance has been reinstalled in another location, it should be put
into operation for the rst charging period under the control of the installer.
Given the weight of the heater with the bricks, it must be taken into account
that both the wall and the supporting oor have sucient strength, in case
of doubt consult your technician. To maintain stability, it is essential that the
heater is located on a level surface and care must be taken to avoid une-
ven surfaces, such as those that can result from carpets or tiled surfaces
that partially bulge under the heater.
Manual de instalación e instrucciones de uso
5
D. INSTALLATION
BEFORE INSTALLATION
The installation and start-up of this appliance is very simple, however, you must read very carefully
all the instructions and recommendations that are detailed in this instruction manual, since
the manufacturer will not be responsible for damage caused by non-compliance.
Once the appliance has been unpacked, the packaging remains must be removed responsibly since
all the elements have been designed for recycling. If, once unpacked, you detect apparent damage
to the appliance, you should consult your supplier before proceeding with the installation and elec-
trical connection within a period of less than 24 hours.
Assembly and installation must be carried out following the instructions detailed in this manual.
The equipment does not need special maintenance. To clean, use a soft, dry cloth, only when the
battery is disconnected and cold. Do not use solvents or abrasive products..
VERY IMPORTANT!
• Read the installation manual before mounting the equipment.
• Read the user manual to handle the equipment.
• Observe the warnings carefully.
• Install the equipment in a place where air can circulate.
• It is advisable that it be assembled by qualied personnel.
ELECTRIC CONNECTION
• In the electrical connection of the appliance, an isolation method must be incorporated into the xed
installation in accordance with the installation regulations in force in the country where it is to be ins-
talled.
• For safety before proceeding with the connection, verify that there is no voltage in the network.
• Before connecting the appliance to the electrical network, make sure that the supply voltage is that
indicated on the 230V rating plate.
• The device must be connected to the protective conductor of the xed installation.
• Any incident derived from non-compliance with these instructions will invalidate the guarantee.
• When connecting, the electrical diagram must be strictly respected, with special attention to the co-
lors of the cables.
WARRANTY
The company oers a technical guarantee according to current legislation in each country. For this
guarantee to be valid, you must present the original of the invoice, delivery note or purchase receipt.
• The warranty only covers manufacturing defects or any problems caused by such defects.
• All problems arising from installation or insucient power (insucient power to heat the room,
incorrect installation, etc.) are not covered by this warranty.
• This radiator is for home use, installation in any other environment is not guaranteed.
• The manufacturer reserves the right to decide whether to repair any defective part or replace all
equipment.
• All costs resulting from damage caused by improper use, transportation, improper power supply,
are not covered by this warranty.
• If the appliance is not installed or positioned as indicated in this manual, the responsible com-
pany will not be liable for possible damages caused by its misuse.
• Any tampering will invalidate the warranty.
• In the last case of resorting to the legislation, both parties will be under the jurisdiction of the
courts of the province of the manufacturer.
Manual de instalación e instrucciones de uso
6
ASSEMBLY INSTRUCTIONS
• For ease of handling, the DS brick and kit are supplied separately.
• The support bases are inside the core of the accumulator.
• The installation of this appliance must be carried out by an authorized installer in accordance
with the ocial regulations in force in each country.
• It is forbidden to place the appliance in places where explosive gases are emitted or with the
presence of ammable products.
• Keep a minimum distance from combustible materials, especially doors, furniture, curtains, clo-
thing, etc. at least 30cm from the front and sides and at least 10cm from the wall (non-combus-
tible).
• Remove the lower screws and remove the front panel by pushing it upwards carefully.
• Once the front panel is removed, the heater core will be visible. When you remove the core cover,
you will nd the support bases and the wall mounting kit.
• Begin by placing the support system. This is done without the need for screws, by inserting the tabs
all the way into the corresponding slots ensuring that the fastening is well done.
• Remove the wall support piece from the equipment (it is pre-assembled with 2 screws at the
back) and present it in its nal location at the height dened in the graphic. With a pencil mark
through the holes provided these points will help us to x the device to the wall.
Manual de instalación e instrucciones de uso
7
• Before xing it to the wall, we must pass the hoses through the most suitable hole.
• Remove the anchor and proceed to make the holes to x the heater to the wall. Once done,
place the support on the wall.
• Position the equipment and screw the wall support piece back to the equipment.
CHARGING THE STORAGE HEATER BLOCKS
• With the appliance already in place and attached to the wall, remove the core cover with extreme
care so as not to damage the insulation or the heating elements.
• Place the blocks inside the core according to the following distribution:
1650 2550 3400
647mm
Manual de instalación e instrucciones de uso
8
• Tilt the resistors forward to facilitate the placement of the blocks with the smooth side on the back.
Once the placement of the blocks is nished, return the heating elements to their vertical position.
• Then place the blocks in front, with the smooth side forward and the notched side toward the resis-
tor, until the entire gap is completed and install the third row of blocks with the smooth side forward.
• Remove the protective plastics from the upper tray and place it on the bricks with the gap facing
down without preventing air from owing and reinstall the front panel of the core.
ELECTRIC CONNECTION
The electrical installation must always be carried out by an authorized installer according to the current
regulations of the supplying Electric Company. To carry out any repair or revision of the appliance,
disconnect it electrically from the mains before opening it.
For its connection, the device has a terminal strip in the lower right area.
Once the assembly is nished and before repositioning the extracted parts, we must carry out the
following checks:
• Check the level of electrical insulation between power terminals and ground. The insulation resistan-
ce must be 0.2 MOhm, under a minimum voltage of 500 V.
• Measure the value of the resistances and the continuity of the circuits.
• With the device connected, measure the consumption, voltage and intensity according to the values
indicated in the table of technical characteristics included in this manual.
ELECTRIC SCHEME
Manual de instalación e instrucciones de uso
9
E. TECHNICAL CHARACTERISTICS
Accumulation power
(W)
Nominal Charger
7h (kWh)
Emission power
(W) Bricks Measures
(mm)
Weight
(Kg)
1650 11,55 625 12 715x743x180 93,5
2550 17,85 950 18 925x743x180 130,0
3400 23,80 1275 24 1035x743x180 170,0
Temperature accuracy +/- 0,1ºC
Temperature setting range
- Comfort
- Economic
- timer
- Anti ice
5 ° C to 30 ° C step every 0.5 ° C
5 ° C to 30 ° C step every 0.5 ° C
5 ° C to 30 ° C step every 0.5 ° C
5 ° C to 30 ° C step every 0.5 ° C
Supply voltage 230 Vac +/- 10% 50Hz
F. USE OF THE STORAGE HEATER
ICONS FROM THE SCREEN
Increase the temperature.
Navigate up.
Reduce the temperature.
Navigate down.
On/O/Mode
Back.
Advanced Settings (5sg).
View current temperature/setpoint temperature.
Manual de instalación e instrucciones de uso
10
Operating modes
The equipment is started / turned o pressing the ON/MODE button and has 3 modes of operation;
OFF mode
In OFF mode, the device is practically o, does not charge and does not heat up.
12:35
OF F
Easy Mode (Fixed Temperature)
In this mode, the device is set to a xed temperature setting (18ºC).
Weekly programming mode
In this mode, the device follows a temperature program. It consists of 3 temperature values (anti-
frost, eco, comfort) that can be adjusted every hour or every half hour.
After starting the device, a start screen appears, which can be the Weekly Programming or the Easy
Programming screen, only one of the two modes can be active.
You can choose which mode to use in the advanced settings, for this;
• Press the CONF button for approximately 5 seconds.
• With the +/- buttons scroll through the dierent options to “ADVANCED” and press ON / MODE.
• Then press ON / MODE again in “FUNC MODE”, once inside you can select (again with the
+/- buttons) between “FIXED TEMPERAT” (easy mode) or “WEEKLY PROGRAM”. Press ON/
MODE to conrm and press the CONF button to exit (press this button as many times as we want
to go backwards).
Set point temperature
Set point temperature
Inhaltsverzeichnis
Andere Electrorad Heizung Handbücher
Beliebte Heizung Handbücher anderer Marken
Empire Heating Systems
Empire Heating Systems WCC65 Bedienungsanleitung
Wetekom
Wetekom 92 86 43 Bedienungsanleitung
Desa
Desa SPC170-F Bedienungsanleitung
Watlow
Watlow Watrod Electric Tubular Heaters Bedienungsanleitung
Haverland
Haverland ECO-DRY GPS Series Stücklistenhandbuch
Stelpro
Stelpro ASILVC2060 Series Bedienungsanleitung