Electrovision Eagle G009MG Bedienungsanleitung
G009MG
Eagle Set of 6 White LED Puck Lights
with PSU
CONGRATULATIONS ON YOUR PURCHASE
Thank you for purchasing this Eagle Puck Light Kit. Please read these instructions carefully
and leave with the user of the product for future reference. If the product is sold on then the
instruction/manual should pass on as well.
BEFORE USE
You must inspect the product and all accessories including any cables, leads and power supply
for signs of damage. If the product is damaged, DO NOT use it, and contact your supplier
immediately.
PRODUCT SAFETY
• Children shall not play with the unit.
• Cleaning and user maintenance shall not be made by children without supervision.
• Please ensure the device is switched o when not in use.
• Do not use the device for other than its intended purpose.
• Do not use this product in bathrooms or other very hot or humid locations.
• Periodically check this product and its power supply for damage. If any is detected do not use
and contact your supplier.
• Do not leave this product switched on while unattended.
• The power supply MUST be kept in a well-ventilated area away from sources of heat and
moisture, such as a cooker and kettles.
INCLUDED IN THE BOX
1 x 6 puck lights 1 x Power supply with inline switch 12 x Wood screws
1 x Junction box 6 x Sticky pads
INFOMATION
• Maximum lead length from the junction box to each light is 2m so try to mount the junction box
in the middle of the installation allowing for a span of up to 4m.
• While the product comes with both doubled sided sticky foam pads and wood screws in most
circumstances the pads on their own will usually be sucient for permanent installation. Before
using the wood screws the installer should take care to make sure they are suitable.
• When using the sticky pads for installation make sure all surfaces are clean and clear of grease
and dust.
INSTALLATION
Fix Each Puck in place using either the sticky foam pads or wood screws. If using the screws
only use the two outer xing points on the puck as per image below. Access to these can be
gained by unscrewing the top of the puck and removing the plastic diuser. This should be
replaced after installation.
Wire each puck to the junction box as per the diagram below. When all of the pucks have been
installed connect the power supply to the junction box and switch on.
MAINTENANCE
There are no user serviceable parts in this product. Periodically check the product for LED failure
and damage. If any of the LED’s have failed or the product is damaged in anyway switch o
and disconnect from the mains supply. To clean the product, switch o and disconnect from the
mains supply. Using a slightly damp cloth gently wipe over. Do not use bleach, solvent based
cleaners or strong detergents. These may damage the product and invalidate the warranty. If
the mains lead is damaged, it must be replaced by the manufacturer or and authorised service
centre.
PAT TESTING
When used in an oce environment, we recommend that this product should be safety-tested
yearly by a qualied electrician (PAT Tested). We recommend that it is PAT tested regularly when
used in a domestic environment.
GENERAL SAFETY REQUIREMENTS
Domestic wiring must be tested periodically by a qualied electrician at least once every 10
years or at every change of occupancy. For oce and retail premises, and buildings such as
village halls, the wiring must be inspected at least once every 5 years. It is recommended that all
building be tted with smoke alarms (it is mandatory for new buildings).
TECHNICAL SPECIFICATION
Power Adaptor Input: ............................................................................................................... 230V
Power Output ................................................................................................................ DC12V 1.5A
Puck Dims .....................................................................................................................60x60x8mm
No of LED’s ...................................................................................................................................18
SERVICE WARRANTY
Electrovision Ltd. guarantees the product free from defects in materials and workmanship for
a period of twelve months. Should this product be operated under conditions other than those
recommended, or any attempts are made to service or modify the product, then the warranty
will be rendered void. The product you buy may sometimes dier slightly from illustrations.
This warranty is in addition to, and does not aect, your statutory rights. Our guarantee is
administered by our retailers. If your product arrives damaged, you must contact the retailer
from whom you bought it. The retailer’s contact details will be on the invoice that arrived with the
product, or on the e-mail you received when you placed the order. Do not contact Electrovision,
only your retailer can arrange a replacement. If the product needs to be repaired or replaced, you
must contact the retailer from whom you bought it. If you have just received your product and
require technical help in using it, please call our Help Desk on (0845) 459 4816
Electrovision Ltd
Lancots Lane
Sutton, St. Helens
Merseyside
WA9 3EX
www.electrovision.co.uk
Inhaltsverzeichnis
Andere Electrovision Beleuchtungsausrüstung Handbücher
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
