Elektra Beckum 091 001 8442 Bedienungsanleitung

115 161 1687 / 1001 - 5.0

091 001 8442

Tischverbreiterung . . . . . . . . . . . . . . . . . . .3

Table Extension . . . . . . . . . . . . . . . . . . . . . .5

Rallonge latérale de table . . . . . . . . . . . . . .7

Tafelverbreding . . . . . . . . . . . . . . . . . . . . . .9

Allargamento del tavolo . . . . . . . . . . . . . . .11

Extensión de la mesa . . . . . . . . . . . . . . . .13

Alargador da bancada . . . . . . . . . . . . . . . .15

Bordforbredelse . . . . . . . . . . . . . . . . . . . . .17

Bordforlengelse . . . . . . . . . . . . . . . . . . . . .19

Tillsatsbord - bredd . . . . . . . . . . . . . . . . . .21

Pöydän levennys . . . . . . . . . . . . . . . . . . . .23

Asztalszélesítő . . . . . . . . . . . . . . . . . . . . . .25

Poszerzenie stołu. . . . . . . . . . . . . . . . . . . .27

Πεπλτυνση του πγκου . . . . . . . . . . . .29

U1A0168.fm

424344454647484950515253

ENGLISH

•Read these instructions before use.

Also observe the instructions for the

circular saw, the safety instructions

in particular.

3Note:

This table side extension is

intended for laterally extending the sup-

port area of the circular saw table (1). In

order to be able to install the table side

extension, the Base System Rails (2) fit-

ting the saw must be installed.

The table side extension can be fitted

either to the left (4) or right (3) hand side

of the saw table. The scale supplied are

intended for installation on the right hand

side, as the sliding carriage can be

intalled on the left hand side.

1. Slide pointer (5) under the two

screws (6) as illustrated and tighten

both screws.

2. Put both clamping plate (7) and coil

spring (8) on the carriage bolt (9) as

ilustrated: The offset ends of the

clamping plate must point towards

the carriage bolt's head.

3. Insert carriage bolt (with fitted

clamping plate and coil spring) from

the outside into the hole of the side

extension's mounting rail.

4. Put distance sleeve (10) from inside

on the carriage bolt and screw on

knurled thumb nut (11), but do not

yet tighten it.

5. Repeat steps 2. though 4. on the

other end of the table side exten-

sion.

6. Slide table side extension into the

two extrusions (12) of the base sys-

tem rails: The table side extension

must be pushed at both ends fully

against the saw table.

7. Tighten knurled thumb nuts (11).

ACaution!

The table side extension must

be exactly level with the saw table,

otherwise workpiece and rip fence

may get caught by the step or rock.

If the table side extension is too low:

Loosen screws (13) on the underside

and slide one or more shim plates (14)

below the table extension's mounting

rails. Tighten screws (13).

Scale alignment

1. Position rip fence (15) at the approx-

imate centre of the table side exten-

sion and lock with ratchet lock lever

(16).

2. Make trial cut: Place workpiece

against rip fence and make a cut.

3. Measure the width of the workpiece

(from edge of cut to rip fence).

4. Loosen fixing screw (17) of the table

side extension's scale.

1. Please Read First!

2. Mounting Locations

3. Assembly

10 11

ELEKTRA BECK

42 43 44 45 46 47 48 49 50 51 52 53

13 14

ELEKTRA BECKUM

23 24 25 26 27 28 29 30 31 32 33 34

KTRA BECKUM

ELEKTRA BECKUM

XA0028E1.fm Operating Instruction ENGLISH

ENGLISH

5. Move scale, until the value indicated

by the left-hand edge of the rip

fence corresponds with the value

measured at the workpiece.

6. Tighten scale fixing screw (17)

again.

7. Set rip fence exactly to 320 mm (for

UK 220 and PK 200) or 520 mm (for

PKF 255) and lock it in position.

8. Loosen scale fixing screw (18) of the

base system rail.

9. Move the base system rail's scale

(19), until the value indicated by the

table extension's pointer (20) corre-

sponds exactly with the rip fence

distance (320 mm or 520 mm

respectively).

10. Tighten scale fixing screw (18)

again.

ARisk of Kickback!

The rip fence's fence extru-

sion must always be exactly parallel

with the saw blade. Otherwise there is

a risk of the workpiece jamming bet-

ween saw blade and rip fence, cau-

sing it to be kicked back against the

operator.

1. Set rip fence exactly to 320 mm (for

UK 220 and PK 200) or 520 mm (for

PKF 255) and lock it in position.

2. Loosen knurled nuts on underside of

the table side extension and set

table extension (with the rip fence)

to desired width. The cutting width is

indicated by the base system rail's

scale.

3. Tighten knurled nuts on underside

of table extension again.

4. Place workpiece against rip fence

and perform the cut.

4. Operation

75 76

45 46 47 48 49 50 51 52

ELEKTRA BECKUM

75 76

32 45 4

23 24 25 26 27 28 29 30 31 32 33 34

A = B

Andere Elektra Beckum Gesehen Handbücher

Elektra Beckum

Elektra Beckum TKHS 315 E/P Series Bedienungsanleitung

Elektra Beckum

Elektra Beckum PKF 255 V8 Bedienungsanleitung

Elektra Beckum

Elektra Beckum TKHS 315 (AUS) Bedienungsanleitung

Elektra Beckum

Elektra Beckum none Beilage

Elektra Beckum

Elektra Beckum Hobbymaster KS 250 Bedienungsanleitung

Elektra Beckum

Elektra Beckum BAS 315 Bedienungsanleitung

Elektra Beckum

Elektra Beckum BAS 500 WNB Bedienungsanleitung

Elektra Beckum

Elektra Beckum ProfiLine UK 220 E Bedienungsanleitung

Elektra Beckum

Elektra Beckum TKHS 315 C Bedienungsanleitung

Elektra Beckum

Elektra Beckum BAS 315 Bedienungsanleitung

Elektra Beckum

Elektra Beckum TKHS 315 Bedienungsanleitung

Elektra Beckum

Elektra Beckum UK 330 Bedienungsanleitung

Elektra Beckum

Elektra Beckum KS 6000 Bedienungsanleitung

Elektra Beckum

Elektra Beckum TKHS 315 C Bedienungsanleitung

Elektra Beckum

Elektra Beckum BAS 315/4 GWN 55 Bedienungsanleitung

Elektra Beckum

Elektra Beckum PK 300 K Bedienungsanleitung

Elektra Beckum

Elektra Beckum BAS 316G DNB Bedienungsanleitung

Elektra Beckum

Elektra Beckum Hobbymaster KS 205 Bedienungsanleitung

Elektra Beckum

Elektra Beckum TKHS 315 E/P 2.2 W Bedienungsanleitung

Elektra Beckum

Elektra Beckum 4 DN Bedienungsanleitung

Elektra Beckum

Elektra Beckum BAS 315 Bedienungsanleitung

Elektra Beckum

Elektra Beckum BAS 500 Bedienungsanleitung

Elektra Beckum

Elektra Beckum BAS 315/4 GWN 55 Bedienungsanleitung

Elektra Beckum

Elektra Beckum BAS 315/4 GDN 55 Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung

Altrad

Altrad BELLE RANGER 450 Bedienungsanleitung

Porter-Cable

Porter-Cable 725 Bedienungsanleitung