ELEPRO R8+ Bedienungsanleitung
USER MANUAL
Low Power Consumption Mini Camera
Mode：R8+
Please read this instruction manual carefully and use it correctly.
After reading, please keep it in a safe place and read it when necessary.
V3.0.3
R
ON
1. Know of the camera
Power/reset
Charging port
Lens
Motion detection
sensor
Mic
Power switch
IR niight lights
Light sensor
Package
contents
l Camera x1
l User manual x1
l SD card reader x1
l 360°Rotating stand x1
l Charging cable x1
Micro SD card slot
Reset
Indicator lighter
Charging
lamp
●
Lit orange
Charging
●
Flash blue
Waiting for connection
●
Lit blue
Wi-Fi connected
●●
Flash red and blue
alternately
Resetting/Soft updating
●●
Flashes red and blue at
the same time
Insufficient battery
●●
Red & blue keep lighting
Malfunction
●
Lit red
AP connected
*In case of failure, please contact support.
2. Set up the camera
[1] Charging
、
ON/OFF
*Please charge before use
About connection
1) WIFI connection: For a Wi-Fi environment,
connect the camera to Wi-Fi and watch remotely.
2) AP connection: For no Wi-Fi environment,
connect directly to the camera, watch within 10M.
3) Single recording: Record with the camera alone
in an environment without a network (memory
card required). Caution: In order to synchronize
the time, connect once after switching on each
time before using.
1) 5V (1A/2A) adaptor for mobile phone and micro-
USB cable is suitable for charging.
2) It takes about 6 hours for fully charged; the lamp
will turn off automatically when fully charged.
*Camera works normally even though keeping
connected to power adapter.
*If the charging indicator light doesn't turn on, try
changing the power cord and charger.
About reset
TIP
1) It supports microSD card and cloud storage
(cloud: billing in the app, detection recording
is overwritten for 3 days free of charge).
2) Class 10 or higher (4~256GB) popular
brand microSD card is recommended.
3) For a new SD card, format it with "TF
Record Settings" in the O-KAM app settings
before using it.
4) 128GB card can record for about 350 hours.
It runs overwriting.
5) Be sure to turn off the power when loading
or removing the microSD card.
TIP
1) In case of user change or Wi-Fi change,
please reconnect and set after resetting.
2) Press and hold the reset button for 6s until the
indicator light flashes red and blue alternately.
[2] Storage
(*Not include)
Purchase available in app
R
ON
OFF
ON
Reset
After registered UBOX account, you should get the verify e-mail from UBIA team. If not, please pay attentionto
whether your mailbox identifies this e-mail as spam.
3.
Get
the
app
Get the ‘O-KAM’ app for free
Scan the QR code or search for ‘O-KAM’ Google Play or App Store
TIP
1) IOS devices 11.0 or higher, Android device 5.0
or higher is supported only.
2) Always update to the latest app.
Register or login the app
Register the O-KAM account before connection.
If you already have an O-KAM account, then login directly.
TIP
You should get a verification code email from the O-KAM team. If you do not receive it, please check
the correctness of your e-mail address, check your junk e-mail folder. And decide your own password.
If it can't get location
automatically, select
your country here first.
1
２
3
Blinks blue slowly: Ready for connection
Blinking blue quickly: Connecting
Lights blue: Connection completed
R
4.
Powering
camera
and
connection the camera to app
[1] Switch the camera power button to ‘ON’
Power switch
TIP
▲ For Wi-Fi connection,
connect your device to your
home 2.4G Wi-Fi first and then
proceed.
[2] Wi-Fi connection steps (for remote viewing)
. .
1
２
6
5
4
3
ON
ON
5.
Connection
without
Wi
-
Fi
AP connection steps (for viewing without Wi-Fi)
If don't have Wi-Fi, connect device directly to the camera within 10M for real-time viewing and settings.
Steps: switch on the camera, do resetting first, and then tap the Wi-Fi (hotspot) ‘LAICAM ***’ in the
WLAN settings of your device as image 1 above, After the ‘!’ Is displayed next to the Wi-Fi mark as
image 2 above, then open the O-KAM app, if the camera is added as image 3 above, it is complete.
TIP
◉For Android devices, wait for a while until the warning message "This WLAN network has no Internet
access." appears as shown in image2 above, and then select "Connect". If this warning is not
displayed, press and hold LAICAM *** to disconnect → reconnect, and a warning will be displayed. ▲
Please note that this warning display disappears immediately for some older Android models.
◉For IOS devices, the camera hotspot has no secret words, so a warning is displayed as "unsecured
network", but the Associated Press is a local network within 10M and your device does not use the
Internet, so it is safe. Try to ignore this warning.
*If close the app, the connection will be automatically disconnected, Tap LAICAM *** and reconnect,
the connection will be restored. multiple cameras cannot be connected at the same time.
*Your device cannot use the Internet until the AP connection is cut off. After completing the settings,
camera will run alone even though close the app.
1
２
3
Android device warning
6.
Recommended
app
settings
You can make general settings for
the app in the ‘Mine’ section
below
Support Google Alexa
Real-time viewing is possible with multiple
cameras at the same time in home page
Manual photos and recordings are recorded
in an "album" from which you can download
to your device or share them.
7.
Share
camera
to
your
family
Share your camera with family and friends
TIP
1) Family and friends need to download the
O-KAM app and register.
2) Send the shared QR code to your family
and follow the instructions to add it.
3) There is no limit to the number of co-
owners. Up to 4 people can watch at the
same time.
権限タイプを選択し、カメラ
を共有へ設定します。
1
3
3
2
Please note the ‘setting permissions’.
Edit permissions, delete share users
オンライ人数
8.
App
features
Add camera
Listing or Four screens
display
Battery volume
connection status
Wi-Fi status
Camera system settings
Camera system settings
Cloud storage recordings
Push notification settings
Memory card recordings
Home page
Camera name
Cloud purchasing &
settings
Battery volume
Wi-Fi status
Full screen switching
Show more
Switching of fineness
Audio of manual
recording or viewing
TIP
*Memory card icon: After the camera is online, it is displayed in gray to black and then can be tapped.
* You can manually record while watching the real-time viewing page, and it will stop when you close
the app. Manual recording is separate from motion detection recording and continuous recording.
Real-time viewing
page
Manual recording
9.
Camera
settings
Camera name
Camera serial number
Wi-Fi status
Camera connection status
Purchase of cloud storage.
(only detection recording can be recorded)
Sleep /continuous recording /deep sleep
mode settings
Firmware update (to always update)
Motion detection, human detection, detection
plane
Camera name editing, image inversion, device
deletion, etc.
SD card format, audio recording on / off
Share your camera with your family
About single recording
Refer to the above AP connection, after the AP connection is made, set it to "Deep sleep" in "Power
mode", disconnected and close the app, and the camera will record by itself.
* It is a power saving mode, but if it is detected frequently, the battery will be consumed faster.
* The hotspot will be hidden after the connection is lost. Since the camera is activated only by moving
objects, try to shaking in front of the lens to reconnect.
When set to "Continuous recording", continuous recording + motion detection recording is performed.
* Due to the hotspot always run, it consumes the battery, camera lasts for about 5 hours.
Inhaltsverzeichnis
