ELEY 1041 Programmierhandbuch
Wall Mount Garden Hose Reel
Model 1041
Assembly & Installation Instructions
Page 2
Reel Specications
Max. Temperature....140° F (60° C)
Max. Pressure.............150 PSI (10 Bar)
CONTENTS
Please DO NOT contact or return this
item to the retailer. Seek assistance
directly from ELEY Corporaon using
the informaon below.
PHONE:
1-866-523-2363 (toll free)
MON- FRI, 8am to 5pm (CST)
E-MAIL:
MON- FRI, 8am to 5pm (CST)
ONLINE:
The SUPPORT secon on our website
www.eleyhosereels.com is available
24/7/365 and contains assembly
videos, repair instrucons and FAQ’s.
QUESTIONS?
PROBLEMS?
123
4 5 6
7
89
10
11
12
13 14
15
10 16
17
Page 3
STEP 1
Place the Front
Flange (4027) on
top of the Back
Flange (4028).
Pins and sockets on
the anges will aid in
proper alignment.
IMPORTANT!
If you purchased an Extra-Capacity Kit
(Item# 1044) with your reel, please refer
to the assembly instructions included
with the Extra-Capacity Kit now. When
you have completed those instructions,
then proceed to Step 3 of this manual.
Standard Reel
Upgraded with
Extra-Capacity Kit
Page 4
STEP 2
Fasten anges together using the three
M6 x 20 Hex Socket Head Cap Screws
(4006) and the small hex end of the
Hex Key Wrench (4003).
STEP 3
Remove the screw from the
Handle Assembly (2654).
STEP 4
Install Handle Assembly
into Front Flange.
Page 5
STEP 5
Remove the two M10 x 25 Hex Socket Head Cap Screws
(4013) and 3/8” Flat Washers (2520) from the Garden
Hose Reel Arm (3071).
STEP 6
Determine which direction you want the reel to operate.
Parallel Perpendicular
STEP 7
Attach the Garden Hose Reel Arm (3071) securely to the Wall Mount Base (2558) using the two
previously removed M10 x 25 Hex Socket Head Cap Screws (4013) and 3/8” Flat Washers (2520).
Parallel Perpendicular
Page 6
Parallel Perpendicular
Step 8
Locate the reel base within 5 feet of your faucet. Note: Be certain there are no other
objects that may interfere with the proper operation of your reel.
Installation Option A - Masonry Walls
(For Option B, stud-wall installation, skip ahead to page 8)
Parallel Perpendicular
Step A9
Use a marker or pencil to mark the location of the four mounting holes on your wall.
Page 7
Step A10
Use a 5/16 inch masonry
bit (not included) and drill
1-1/2 inch deep holes at
the 4 marked locations.
Helpful hints:
Measure and then mark
the masonry bit with
masking tape to ensure
you drill at the proper
depth. Clean the holes
with a shop vacuum.
Wear eye and dust
protection.
Step A11
Position the Wall Mounting Base over the drilled holes and tap the four 5/16” x 1-3/4” Sleeve
Anchor Bolts (2598) through the base and into the holes in the wall.
Step A12
Tighten the four sleeve anchor bolts with a 7/16 inch wrench. Do not over tighten.
PerpendicularParallel
PerpendicularParallel
Proceed to step 13
on page 10.
Page 9
Installation Option B - Stud Walls
Parallel Perpendicular
Step B10
Use a 1/8 inch drill bit (not included) and drill 1-1/2 inch deep holes at the four marked locations.
Helpful hint: Measure and then mark the drill bit with masking tape to ensure you drill at the
proper depth. Wear eye protection.
Step B9
Use a marker or pencil to mark the location of the four mounting holes on your wall.
Note: Locate studs prior to drilling. The reel must be fastened to 2 studs.
Page 8
Perpendicular
Step B12
Tighten the four 1/4 x 2-1/2 inch Hex Head Lag Screws (2319) with a 7/16 inch wrench.
Do not over tighten.
Page 9
Perpendicular
Parallel
Step B11
If you are fastening to lap siding, use the four Standoffs (2510) between the Wall Mounting base
and the siding. Fasten the base to the wall with the four 1/4 x 2-1/2 inch Hex Head Lag Screws
(2319) and 1/4 inch Flat Washers (2331).
Parallel
Page 10
PerpendicularParallel
Step 13 - Insert the externally threaded (male) end of the Inlet hose (1087) into the axle tube
until it is accessible from the other side.
Step 14 - Install the Flange Assembly onto the axle with the crank handle to the outside.
Step 15 - Install the Cam-lever Brake (2587) onto the axle.
Note: Align the tab on the brake with the notch in the ange.
PerpendicularParallel
PerpendicularParallel
Andere Handbücher für 1041
1
Inhaltsverzeichnis
Andere ELEY Kabel und Steckverbinder Handbücher
